Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
USING R-12 & R-134a REFRIGERANT HANDLING/SAFETY PRECAUTIONS 1) Always work in a well-ventilated, clean area. Avoid breathing refrigerant vapors. Exposure may irritate eyes, nose and throat. Refrigerant is colorless and is invisible as a gas. Refrigerant is heavier than oxygen and will displace oxygen in a confined area. 2) The A/C system high pressure can cause severe injury to eyes and skin if a hose were to burst. Always wear eye protection, gloves and other protective clothing when working around A/C system and refrigerant. 3) Refrigerant evaporates quickly when exposed to atmosphere, freezing anything it contacts. If liquid refrigerant contacts eyes or skin (frostbite), DO NOT rub eyes or skin. Immediately flush affected area with cool water for 15 minutes and consult a doctor or hospital. 4) Never use R-134a in combination with compressed air for leak testing. Pressurized R-134a in the presence of oxygen (air concentrations greater than 60 percent by volume) may form a combustible mixture. DO NOT introduce compressed air into R-134a containers (full or empty), A/C system components or service equipment.

download
Instrument panel: 1. Remove the center air vent. 2. Remove the climate control unit and audio unit as an assembly (’96 – 98 models, ‘99 – 04 models). NOTE: Do not disconnect the connectors. 3. Remove the dashboard lower cover and driver’s switch trim. 4. Remove the screws, detach the clips, then carefully pull out the instrument panel in the numbered sequence. Disconnect the connector, then remove it. NOTE: Release the adhesive at the left side of the skirt carefully. 5. Installation is the reverse of the removal procedure. NOTE: Make sure the connections are connected properly. Dashboard lower cover: Detach the clips, then remove the dashboard lower cover. Installation is the reverse of the removal procedure. Driver’s switch trim: 1. Remove the dashboard lower cover. Climate control unit and audio unit (’96 – 98 models):

download
Special Tools Required Brake caliper piston compressor 07AAE-SEPA101 CAUTION: Frequent inhalation of brake pad dust, regardless of material composition, could be hazardous to your health. Avoid breathing dust particles. Never use an air hose or brush to clean brake assemblies. Use an OSHA- approved vacuum cleaner. Replacement NOTE: Due to the high performance nature of the brake system, the rotors and pads may wear faster. Be sure to inspect the front rotor thickness anytime the front pads are replaced. 1. Raise the front of the vehicle, and support it with safety stands in the proper locations. 2. Remove the front wheels.

download
1. Remove fuel tank filler cap. Listen for fuel pump operation noise at fuel tank filler. Fuel pump should operate for 2 seconds after ignition switch is turned on. If fuel pump operates as specified, fuel pump is okay. If fuel pump does not operate as specified, go to next step. 2. Turn ignition switch off. Remove rear seat or trunk floor to gain access to fuel pump connector. Disconnect fuel pump connector. Disconnect PGM-FI main relay connector. Connect a fused jumper wire between PGM-FI main relay connector FUEL PUMP fuse side terminal and fuel pump side terminal. See L – WIRING DIAGRAMS article. 3. Turn ignition switch on. Using a voltmeter connected to ground, check for battery voltage at fuel pump harness side connector. See L – WIRING DIAGRAMS article. If battery voltage is not present, check harness between fuel pump and FUEL PUMP fuse. Repair as necessary. If battery voltage is present, check fuel pump ground. Repair as necessary. If ground is okay, replace fuel pump.

download
SRS components are located in this area. Review the SRS component locations (see COMPONENT LOCATION INDEX ) and the precautions and procedures (see PRECAUTIONS AND PROCEDURES ) before performing repairs or service. 1. Make sure you have the anti-theft codes for the radio and the navigation system, then write down the customer’s audio presets.
2. Align the front wheels straight ahead, then remove the driver’s airbag from the steering wheel (see DRIVER’S AIRBAG REPLACEMENT ).
3. Disconnect the cable reel subharness connector (A) from the cable reel.