Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
1. Remove the headlamp fasteners. 2. Using a pry bar, gently pry in the center area of the headlamp assembly. Pry the headlamp assembly straight forward in order to unsnap the headlamp ball stud from the ball stud socket. 3. Slide the headlamp straight forward and disconnect the headlamp electrical connectors from the forward lamp wiring harness. 4. Remove the headlamp from the vehicle. INSTALLATION PROCEDURE 1. Install the headlamp to the vehicle. 2. Connect the electrical connectors. 3. Position the headlamp in order to align the locator pins with the headlamp mounting bracket. 4. Press the headlamp rearward in order to engage the ball stud with the ball stud socket. 5. Install the headlamp fasteners. NOTE: Refer to Fastener Notice in Service Precautions. Tighten Tighten the headlamp mounting fasteners to 9 N.m (80 lb in) .

download
IMPORTANT: When replacing a theft deterrent control module with an GM Service Parts Operation (SPO) Replacement Part, set up the control module prior to the 10-minute relearn procedure or the 30-minute relearn procedure. TOOLS REQUIRED Scan tool SET UP A NEW THEFT DETERRENT CONTROL MODULE Use this procedure only if replacing the theft deterrent control module with an GM SPO Replacement Part. 1. Connect a scan tool to the vehicle. 2. Turn ON the ignition, with the engine OFF. 3. With a scan tool, select Setup New VTD Module in the Vehicle Theft Deterrent, Special Functions data list. 4. Follow the scan tool on-screen instructions. IMPORTANT: When replacing a theft deterrent control module with an GM SPO Replacement Part, the module will learn the keys immediately. The existing powertrain control module (PCM) must learn the new fuel continue password when you replace the theft deterrent control module. When replacing a PCM with a GM SPO Replacement Part, the new PCM will learn the incoming fuel continue password immediately after programming and upon receipt of a password message. Once a password message is received and a password is learned, perform the learn procedure to change this password again. A PCM which had been installed in another vehicle will have learned the fuel continue password of the other vehicle’s theft deterrent control module. Perform either the 10-minute relearn procedure or the 30-minute relearn procedure after programming to learn the fuel continue password of the current vehicle’s theft deterrent control modules. When performing either relearn procedure, all previously learned keys will be erased from the theft deterrent control module’s memory. Additional keys may be learned immediately after the first relearn

download
Remove switch plate with small thin bladed tool at forward retainer clip. Disconnect wire harness. Insert small thin-bladed tool between side of warning lamp/reflector and armrest base to release retaining tab. Disconnect wire connector. Remove escutcheon screw. Disconnect wire harness. Disconnect lock control lever and escutcheon. Remove two screws and pull handle (Park Avenue). Remove trim panel retaining screws. Release trim panel fasteners. Carefully feed wire harness through door. Remove trim panel. Disconnect wire connector and speaker (if equipped). Remove armrest bracket and pull handle brackets then carefully peel water deflector from inner door panel. Remove two screws from the back of the HVAC control (RH side) or headlamp switch (LH side) then remove control/switch from applique. Remove six applique nuts. Remove applique. 18. 19. 20. 21. Gently pry courtesy lamp lens and remove. Remove eight nuts. Remove carpet. Remove speaker cover.

download
REMOVE OR DISCONNECT 1. Retainer and electrical connector from fluid level sensor. 2. Drain brake fluid front mister cylinder reservoir. 3. Reservoir hose from master cylinder. Plug hose to prevent fluid loss and contamination. 4. Brake pipes from master cylinder. Plug open pipes to prevent fluid loss and contamination. 5. Two attaching nuts. 6. Master cylinder. 7. Reservoir, if it is to he used on replacement master cylinder. INSTALL OR CONNECT Reservoir onto master cylinder, as needed. Master cylinder on to power booster. Attaching nuts. Tighten to 27 Nm (20 lb. ft.). Brake pipes. Tighten brake pipe fittings to 15 Nm (11 lb. ft.). Reservoir hose onto master cylinder. Fill master cylinder reservoir to full level mark using only Delco Supreme 11 Brake Fluid, or equivalent DOT 3 brake fluid. 7. Electrical connector to fluid level sensor, secure with retainer. 8. Bleed hydraulic system. 9. Recheck fluid level in reservoir. 1. 2. 3. 4. 5. 6.

download
1. 2. 3. 4. 5. Raise and support the vehicle. Refer to Vehicle Lifting. Position the oil drain pan under the engine oil drain plug. Remove the engine oil drain plug. Clean and inspect the engine oil drain plug, repair or replace if necessary. Clean and inspect the engine oil drain plug sealing surface on the oil pan, repair or replace oil pan if necessary. 6. Remove the oil filter. 7. Clean and inspect the oil filter sealing area on the engine block, repair or replace if necessary. Installation Procedure 1. Lightly oil the replacement oil filter gasket with clean oil and install the new oil filter. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the new oil filter. Tighten the new oil filter to 3/4 to 1 full turn, after the oil filter gasket contacts the oil filter mounting surface. 3. Install the engine oil drain plug. Tighten the plug to 30 Nm (22 ft. lbs.) . 4. 5. 6. 7. 8. 9. Remove the oil drain pan. Lower the vehicle. Fill the engine with new engine oil. Start the engine. Inspect for oil leaks after engine start up. Turn off the engine and allow the oil a few minutes to drain back into the oil pan. Remove the oil level indicator from the oil level indicator tube. Clean off the indicator end of the oil level indicator with a clean paper towel or cloth. Install the oil level indicator into the oil level indicator tube until the oil level indicator handle contacts the top of the oil level indicator tube. Again, remove the oil level indicator from the oil level indicator tube keeping the tip of the oil level indicator down. Check the level of the engine oil on the oil level indicator. If necessary, adjust the oil level by adding or draining the engine oil. 10. 11. 12. 13. 14. 15.