22re remove crank pulley


You are searching repair manual in PDF format about 22re remove crank pulley use another keyword for search another post or files



  22re remove crank pulley Direct Download speed 5787 Kb/s

  22re remove crank pulley Full Version speed 6767 Kb/s




1993 Mitsubishi Montero TRANSFER CASE DISASSEMBLY

0

Filed Under (Mitsubishi) by admin on 30-12-2010

download
Disassembly (Ram-50) 1) Remove both 4WD indicator switches and steel balls. Remove speedometer gear assembly. Remove output shaft cover, gasket, wave spring and spacer. See Fig. 3. Remove rear cover, rear cover gasket and spacer from chain cover. Drive roll pin out of high-low shift fork. 2) Remove 2 seal plugs. Remove 2 poppet springs and steel balls. Shift transfer case to “4WD” and pull high-low shift rail out, in rear cover direction. Remove interlock plunger. Remove pulse generator (if equipped), front output shaft cover and pulse rotor (if equipped). Remove snap ring from rear bearing on output shaft. Remove chain cover, oil guide and side cover. Remove countershaft locking plate. Remove countershaft. 3) Remove countergear, 2 thrust washers, 2 needle bearings and spacer through side cover opening. Remove snap ring, spring retainers and spring from 2WD-4WD shift rail. Remove front output shaft, rear output shaft and chain as assembly. 4) Remove 2WD-4WD shift fork and distance piece. Drive out 2WD-4WD shift rail spring pin. Remove 2WD-4WD shift rail and lug. Remove high-low shift fork and high-low synchronizer sleeve. Remove needle bearing and snap ring from input gear. Remove input gear assembly. 5) If either control shaft or input gear oil seals are to be replaced, drive out roll pin from transmission control change shifter. Separate transfer case from adapter. See Fig. 3. Disassembly (Montero) 1) Remove dynamic damper, 5 detection switches and 3 steel balls. Remove poppet plug, spring and steel ball. Remove speedometer gear assembly. Remove output shaft rear cover, spacers, dust seal guard and oil seals. Front output shaft cover, wave spring and spacer (if equipped). 2) Remove high-low shift rail plug and high-low shift fork spring pin. Shift transfer case to “4WD”. Remove rear cover and high- low shift rail. Remove interlock plunger. Remove rear output shaft (viscous coupling) assembly and center differential assembly. Remove 2WD-4WD synchronizer assembly, chain and front output shaft from transmission as a unit. With White paint make match marks in grooves of 2WD-4WD synchronizer in 3 places. With White paint make match marks on spline projections of 2WD-4WD synchronizer sleeve in 3 places. Refer to match marks during reassembly. 3) Remove snap ring, spring seat, spring, 2WD-4WD shift fork and 2WD-4WD synchronizer sleeve. Remove differential lock hub, oil dam cover and bearing retainer. Remove side cover and gasket. Remove transfer counter gear shaft, transfer counter gear, thrust washer, needle bearings and spacer. Remove transfer drive shaft assembly. Remove high-low shift fork assembly and clutch sleeve. Remove transfer input gear assembly. 4) Remove 2WD-4WD shift lug spring pin, spring, spring retainer 2WD-4WD shift lug and shift rail. Remove input gear oil seal, baffle plate, dust seal guard and front output shaft oil seal. See Fig. 4.

Related entry:

vw t4 gear lever removal, f250 ashtray removal, how to remove a visor from a subaru outback, 1996 VW Golf Manual Shift Linkage, c220 front spring removal, Remove Snap ring on 2004 toureg drive shaft, disconnect anti theft fuse on 1991 sadandiville diagram, steps for disconnecting the electrical connectors on the back of the steering wheel airbag on a 2000 Chevy Venture, How to replace an antenna on a S10 blazer, how to remove zafira bumper,

1994 Ford Mustang A/C Evaporator Housing Removal and Installation

0

Filed Under (Ford) by admin on 06-03-2011

download
1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed. Refer to Section 15-01. If the vehicle doesn’t have a radio chassis , use a small screwdriver and pry radio cover finish panel out of console. 9. Flex glove compartment bin tabs inward. Drop down glove compartment (06010) assembly. Remove two console-to-instrument panel retaining screws. 10. Remove four console bracket retaining screws. Remove console panel from vehicle. 11. Remove three bolts retaining steering column opening cover (3A673) and reinforcement panel. Remove cover. 12. Remove steering column opening reinforcement by removing two bolts. 13. Remove two bolts retaining steering column opening reinforcement and remove reinforcement. 14. Remove six steering column retaining nuts (two retaining the hood release mechanism and four retaining column to lower brake pedal support). Lower steering column to floor. 15. Remove upper and lower steering column shrouds (3530) and disconnect wiring from turn signal and windshield wiper switch (13K359) . 16. Remove steering column through bolt and nut on engine compartment side of cowl panel. Remove steering column from vehicle. 17. Remove brake pedal support nut. 18. Snap out instrument panel defroster opening grille (044E82) . 19. Remove screws from speaker covers. Snap out speaker covers. 20. Remove front screws retaining RH and LH scuff plates at cowl side trim panels. 21. Remove RH and LH cowl side trim panels. 22. Disconnect wiring at RH cowl side. 23. Remove cowl side retaining bolts (one each side). 24. Remove five cowl top screws attachments. 25. Gently pull instrument panel (04320) away from RH side of cowl panel. Disconnect speedometer cable, air conditioning controls and wire connectors. 26. Place a drain pan or suitable container under the heater water hose connections at the cowl panel. 27. Disconnect heater water hoses (18472) from heater core tubes and plug heater water hoses with suitable 5/8-inch and 3/4-inch plugs. Cap heater core tubes to prevent coolant loss from heater core (18476) during removal of heater case. 28. Remove screw retaining A/C evaporator case support bracket (19A639) to cowl top panel. 29. Disconnect vacuum supply supply hose (black) from A/C vacuum supply in engine compartment. 30. Working under the hood (16612) , remove nut retaining heater case to cowl panel. 31. Inside passenger compartment, remove screw retaining A/C evaporator case mounting bracket (19A865) to cowl top panel. 32. Remove one screw retaining A/C evaporator case mounting bracket below heater case to cowl panel. 33. Carefully pull heater case from cowl panel and remove heater case assembly from vehicle. 34. To install, reverse Removal procedure. Check operation of all components. 35. After repairs have been completed, check the coolant level in the radiator (8005) and in the radiator coolant recovery reservoir (8A080) . Fill as required with the recommended coolant mixture.

Related entry:

remove the rocker panel cover on 2006 altima, How to remove center console cup holder in a 06 f150 super cab, how to remove overhead console on 2005 aviator youtube, 94 FORD BRONCO FRONT BUMPER REMOVAL, how to use bottom compartment of prius 2008, how to remove 1999 cavalier center console, how to take off center console \04 lincoln aviat, removing 2003 sienna instrument panel, how to remove center console 2006 Jetta, console removal in a cobalt video,

1997 Ford F-250/350/Super Duty Engine Front Cover Removal

0

Filed Under (Ford) by admin on 06-03-2011

download
Crankshaft front seal replacement is recommended whenever the engine front cover (6019) has been removed. 1. Disconnect battery ground cable (14301). Drain crankcase. 2. Drain cooling system. Refer to Section 03-03. 3. Remove drive belts (8620). Refer to Section 03-05. 4. Remove bolts attaching fan shroud (8146) to radiator (8005). 5. Remove fan blade (8600) from fan clutch (8A616) and remove fan shroud. 6. Remove fan clutch and water pump pulley (8509) from water pump (8501). 7. Disconnect upper radiator hose (8260) and lower radiator hose (8286) at engine (6007). Disconnect transmission oil cooler lines at radiator. 8. Remove upper radiator support bracket and remove radiator. 9. Remove generator pivot and attaching bolts. Remove generator (GEN) (10300) from generator mounting bracket (10153) and generator adjusting arm (10145). 10. Remove two bolts attaching generator adjusting arm to water pump and generator mounting bracket and remove generator adjusting arm. 11. Remove air pump pivot and attaching bolts. Remove secondary air injection pump (AIR pump) (9A486) from generator mounting bracket. 12. Remove four bolts attaching generator mounting bracket to cylinder head (6049), cylinder blocks (6010) and water pump, and remove generator mounting bracket. 13. Remove power steering pump pulley (3A733) from power steering pump (3A674). 14. Remove power steering lines from power steering pump. Remove four bolts attaching power steering pump to A/C compressor mounting bracket (2882) and remove power steering pump from A/C compressor mounting bracket. 15. Remove four bolts attaching A/C compressor (19703) to A/C compressor mounting bracket. Remove four bolts and one nut attaching A/C compressor mounting bracket to cylinder head and water pump. Remove A/C compressor mounting bracket from engine. 16. Remove the crankshaft pulley (6312) from the crankshaft vibration damper (6316). 17. Remove bolt and washer attaching crankshaft vibration damper. Remove crankshaft vibration damper using Crankshaft Damper Remover T58P-6316-D or Rotunda Gear and Pulley Puller 014-00293 or equivalent. Remove Woodruff key and crankshaft damper spacer from crankshaft (6303).

Related entry:

how to remove hydralic coolin fan pump pully, how to remove cranl pully 98 ranger 2 5, navistar 8600 service manual, remove bracket rusted to railing, torque spec for 03 cavalier brake caliper,

1996 Nissan Altima GLE TIMING CHAIN Removal

0

Filed Under (Nissan) by admin on 28-11-2010

download
1. Release fuel pressure. See FUEL PRESSURE RELEASE . Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses, fuel lines and control cables. 2. Remove front exhaust tube. Remove intake manifold collector supports, and intake manifold. Remove exhaust manifold with catalytic converter. Remove air injection valve pipe. Remove intake air duct. Remove radiator fan and shroud. Remove injectors and fuel rail as an assembly. Remove distributor cap and spark plugs. 3. Set cylinder No. 1 at TDC of compression stroke, ensuring marks on crankshaft pulley and front cover align, and distributor rotor points to spark plug wire No. 1 on cap. Remove cylinder head cover. Remove distributor. NOTE: It is not necessary to install a stopper to prevent inner or outer timing chains from disengaging sprockets. 4. Prevent camshafts from turning, and remove camshaft sprocket bolts. Remove camshaft sprocket. See Fig. 13 . Mark and remove camshaft bearing caps in reverse order of installation. See Fig. 16 . Remove camshafts. 5. Loosen cylinder head bolts in 2 or 3 steps, in reverse order of tightening sequence. See Fig. 11 . Remove camshaft sprocket cover. Remove outer (upper) chain tensioner and guide. Remove outer timing chain. Remove idler sprocket bolt. Remove cylinder head. 6. Remove oil pan and oil strainer. See OIL PAN. Remove accessory drive belts. Remove A/C compressor idler pulley (if equipped). Remove crankshaft pulley. Remove front cover. Remove chain tensioner, tensioner arm and chain guides. Remove inner (lower) timing chain and idler sprocket. Remove oil pump drive spacer and crankshaft sprocket. Inspection 1. Inspect chain roller links. Replace chain if roller links are cracked or worn. Inspect cylinder head and cylinder block mating surfaces for warpage. If warpage exceeds specification, machine cylinder head. See CYLINDER HEAD under ENGINE SPECIFICATIONS. 2. If machining reduces cylinder head height to less than specification, replace cylinder head. After machining, rotate camshaft by hand. Replace cylinder head if camshaft does not rotate freely. Installation

Related entry:

how to remove the key cylinder from a 2003 KIA RIO, kia rio lock cylinder, 2001 kia rio ignition cylinder removing, 2006 Kia Optima ignition switch, 2006 kia rio ignition cylinder removal, Ignition Cylinder Lock kia, Kia Optima Ignition Lock Cylinder, removing kia rio ignition cylinder,

1998 Nissan Sentra TIMING CHAIN Removal

0

Filed Under (Nissan) by admin on 27-11-2010

download
CAUTION: If camshaft or crankshaft is rotated with timing chain disconnected, piston will contact valves, resulting in bent valves. NOTE: For reassembly reference, apply paint marks to timing chain and camshaft sprockets before removing. Removal 1. Release fuel pressure. See FUEL PRESSURE RELEASE . Drain coolant from radiator and cylinder block (drain plug is on left side of block, between flywheel and exhaust manifold). Remove accessory drive belts and power steering pump bracket. Remove intake air duct. Remove right front wheel and splash shield. 2. Remove engine undercovers. Remove front exhaust pipe. Remove front engine mount from cylinder head. Remove cylinder head cover, distributor cap and spark plugs. Remove intake manifold support. Set piston No. 1 at TDC of compression stroke. For installation reference, mark rotor in relation to distributor housing and distributor housing in relation to cylinder head. Remove distributor. 3. Remove cylinder head front cover. See Fig. 4 . Remove water pump pulley and thermostat housing. Remove chain tensioner and guide. See Fig. 6 . Loosen idler sprocket bolt. Remove camshaft sprockets. Remove idler sprocket bolt. Remove cylinder head bolts in 2 steps, in sequence. See Fig. 5 . Remove cylinder head with manifolds. Remove idler sprocket shaft from rear side. Remove outer (upper) timing chain. 4. Remove crossmember and rear engine mount. Remove oil pan and strainer. Remove crankshaft pulley. Support engine using a jack. Remove front engine mount. Remove front cover bolts (one of these bolts retains water pump and front cover). Remove front cover. Remove idler sprocket, inner (lower) timing chain and oil pump drive spacer. Remove chain guides and crankshaft sprocket.

Related entry:

2003 nissan altima 2 5 head removal, 2003 nissan altima 2 6 engine removal, how to remove the head from a 2 5 engine in a 2003 nissan altima, nissan sentra intake manifold water sender, removing 2 5 nessan centra engine,