01 Impala intake manifold torque specs


You are searching repair manual in PDF format about 01 Impala intake manifold torque specs use another keyword for search another post or files



  01 Impala intake manifold torque specs Direct Download speed 5787 Kb/s

  01 Impala intake manifold torque specs Full Version speed 6767 Kb/s




1997 Chevy K 1500 Intake Manifold Replacement (Upper)

0

Filed Under (Chevrolet) by admin on 19-09-2010

download
REMOVAL 1. Disconnect the battery negative cable assembly from the battery negative terminal. 2. Remove the air cleaner assembly. Refer to Powertrain Management. 3. Remove the wiring harness connectors and the brackets and move aside. 4. Remove the throttle cable and the bracket from the upper intake manifold. 5. Remove the cruise control cable, (if equipped). 6. Remove the fuel lines from the intake to the rear of the block. Refer to Powertrain Management. 7. Remove the ignition coil and the bracket. Refer to Starting and Charging 8. Remove the upper intake manifold. INSTALLATION 1. Install the upper intake manifold gasket. 2. Install the upper intake manifold. Use care not to pinch the injector lines between the upper and lower intake manifolds. 3. Install the upper intake manifold bolts. Note the marks made at disassembly for proper stud location. Install the two corner studs first in order to help align the two halves. AllData Editor NOTE: Other than the two torque passes listed below, the OE Manufacturer did NOT address or supply a bolt tightening sequence for the upper Intake Manifold for this model year, or other model years where this 2 piece manifold setup is used. A “Play It Safe” final tightening sequence would be to tighten from the center most bolts to the outer most bolts. 4. Tighten the bolts in two steps: a. Tighten the bolts on the first sequence to 5 Nm (44 inch lbs.). b. Tighten the bolts on the final sequence to 10 Nm (88 inch lbs.). 5. Install the purge solenoid and bracket. Refer to Powertrain Management. 6. Install the ignition coil and bracket. Refer to Starting and Charging. 7. Install the PCV hose et the upper intake manifold. 8. Install the fuel lines from the intake at the rear of the block. Refer to Powertrain Management. 9. Install the cruise control cable (if equipped). 10. Install the throttle cable and bracket from the upper intake manifold. Refer to Powertrain Management. 11. Install the wiring harness connectors and brackets. 12. Install the air cleaner assembly. Refer to Powertrain Management. 13. Connect the battery negative cable assembly to the battery negative terminal. – Tighten the bolt to 15 Nm (11 ft. lbs.).

Related entry:

torque settings for 2005 dodge caravan 3 3 engine intake manifold, where is intake manifold runner control on 1996 ford explorer, 2002 jaguar x-type 2 5 intake manifold torque sequence, 2001 ford mustang 3 8l intake runner clips, intake torque specs for 2004 freestar, explode veiw 2001 4 0 intake vacum lines, inlet manifold tightening sequence pt cruiser, diagram of 1995 chevy caprice manifold repair, 2003 mercury sable dohc plenum removal, pdf file for 97 f-150 4 2 intake gasket,

1997 Chevy C Tahoe Intake Manifold Replacement (Upper)

0

Filed Under (Chevrolet) by admin on 20-09-2010

download
REMOVAL 1. Disconnect the battery negative cable assembly from the battery negative terminal. 2. Remove the air cleaner assembly. Refer to Powertrain Management. 3. Remove the wiring harness connectors and the brackets and move aside. 4. Remove the throttle cable and the bracket from the upper intake manifold. 5. Remove the cruise control cable, (if equipped). 6. Remove the fuel lines from the intake to the rear of the block. Refer to Powertrain Management. 7. Remove the ignition coil and the bracket. Refer to Starting and Charging 8. Remove the upper intake manifold. INSTALLATION 1. Install the upper intake manifold gasket. 2. Install the upper intake manifold. Use care not to pinch the injector lines between the upper and lower intake manifolds. 3. Install the upper intake manifold bolts. Note the marks made at disassembly for proper stud location. Install the two corner studs first in order to help align the two halves.Other than the two torque passes listed below, the OE Manufacturer did NOT address or supply a bolt tightening sequence for the upper Intake Manifold for this model year, or other model years where this 2 piece manifold setup is used. A “Play It Safe” final tightening sequence would be to tighten from the center most bolts to the outer most bolts. 4. Tighten the bolts in two steps: a. Tighten the bolts on the first sequence to 5 Nm (44 inch lbs.). b. Tighten the bolts on the final sequence to 10 Nm (88 inch lbs.). 5. Install the purge solenoid and bracket. Refer to Powertrain Management. 6. Install the ignition coil and bracket. Refer to Starting and Charging. 7. Install the PCV hose et the upper intake manifold. 8. Install the fuel lines from the intake at the rear of the block. Refer to Powertrain Management. 9. Install the cruise control cable (if equipped). 10. Install the throttle cable and bracket from the upper intake manifold. Refer to Powertrain Management. 11. Install the wiring harness connectors and brackets. 12. Install the air cleaner assembly. Refer to Powertrain Management. 13. Connect the battery negative cable assembly to the battery negative terminal. – Tighten the bolt to 15 Nm (11 ft. lbs.).

Related entry:

2003 yukon 6 0l Intake Manifold bolt sequence, how to replace ford ka 2002 inlet manifold gasket with pictures,

2006 Ford Five Hundred SE Upper Intake Manifold Removal

0

Filed Under (Ford) by admin on 22-01-2011

download
All vehicles 1. Drain the cooling system. For additional information, refer to DRAINING . 2. Disconnect the battery ground cable. For additional information, refer to REMOVAL AND INSTALLATION . 3. Remove the air cleaner outlet pipe. For additional information, refer to REMOVAL AND INSTALLATION . 4. Remove the 4 transaxle roll restrictor cross brace bolts.5. Remove the bolt and the transaxle roll restrictor cross brace. 6. Disconnect the evaporative emissions (EVAP) canister purge valve tube from the upper intake manifold and detach the retainer. 7. Disconnect the positive crankcase ventilation (PCV), brake booster and vacuum harness tubes from the upper intake manifold. 8. Detach the fuel tube retainer from the upper intake manifold. 9. Disconnect the exhaust gas recirculation (EGR) system module electrical connector and vacuum tube. 10. Detach the vacuum tube from the upper intake manifold vacuum tube retainer. 11. Disconnect the EGR system module tube from the EGR system module. Early build 12. Disconnect and plug the throttle body and PCV coolant hoses. Late build 13. Disconnect and plug the 2 PCV coolant hoses. All vehicles 14. Disconnect the throttle body electrical connector. 15. If equipped, remove and discard the 4 upper-to-lower intake manifold screws. 16. Remove the 8 bolts and the upper intake manifold. Remove and discard the gaskets. Installation All vehicles NOTE: Clean and inspect all sealing surfaces. Install new gaskets. 1. Position the upper intake manifold and install the 8 bolts. Tighten in the sequence shown to 10 N.m (89 lb-in). 2. Connect the throttle body electrical connector. Late build 3. Connect the 2 PCV coolant hoses. Early build 4. Connect the throttle body and PCV coolant hoses. All vehicle 5. Connect the EGR system module tube to the EGR system module. Tighten to 40 N.m (30 lb-ft). 6. Attach the vacuum tube to the upper intake manifold vacuum tube retainer. 7. Connect the EGR system module electrical connector and vacuum tube. 8. Attach the fuel tube retainer to the upper intake manifold. 9. Connect the PCV, brake booster and vacuum harness tubes to the upper intake manifold. 10. Connect the EVAP canister purge valve tube to the upper intake manifold and attach the retainer. 11. Clean the 4 transaxle roll restrictor cross brace bolts using a wire brush and apply new threadlock to the threads. 12. Position the transaxle roll restrictor cross brace and install the 4 new bolts. Tighten to 55 N.m (41 lb-ft). 13. Clean the transaxle roll restrictor cross brace-to-roll restrictor bolt using a wire brush and apply new threadlock to the threads. 14. Install a new transaxle roll restrictor cross brace-to-roll restrictor bolt. Tighten to 48 N.m (35 lb-ft). 15. Install the air cleaner outlet pipe. For additional information, refer to REMOVAL AND INSTALLATION . 16. Connect the battery ground cable. For additional information, refer to REMOVAL AND INSTALLATION . 17. Fill and bleed the cooling system.

Related entry:

03 freelander intake manifold tuning valve, removing upper intake plenum for a 2006 altima 3 5, intake runner control throttle ford focus LX 2000, intake manifold tunning valve for saturn outlook, 20054 2freestarintakecrosssectionimage, how to remove manifold toyota sienna 2006, 2003 isuzu rodeo intake removal, how to assemble a crankcase ventilation tube to a pressure control valve 2005 audi a4 1 8T, bolt torque for intake manifold 2001 taurus, does intake manifold tuning valve wire rub on a/c pipe on mit eclipse 2003 car?,

2002 Chevrolet Impala Intake Manifold Replacement – Lower Removal Procedure

0

Filed Under (Chevrolet) by admin on 21-01-2011

download
1. 2. 3. 4. Disconnect the negative bakery. Remove the upper intake manifold. Remove the left valve rocker arm cover. Remove the right valve rocker arm cover. 5. Disconnect the Engine Coolant Temperature (ECT) sensor electrical connector. 6. Disconnect and remove the fuel injector and the Manifold Absolute Pressure (MAP) sensor wiring harnesses. 7. Remove the fuel pipe clip bolt. 8. Remove the fuel pipe clip. 9. Remove the fuel feed pipe from the fuel injector rail. 10. Remove the fuel return pipe from the fuel injector rail. 11. Remove the fuel injector rail. 12. Remove the power steering pump from the front engine cover and reposition. 13. Remove the heater inlet pipe with heater hose from the lower intake manifold and reposition. 14. Remove the radiator inlet hose from the engine. 15. Remove the thermostat bypass hose from the thermostat bypass pipe and lower intake manifold pipe. 16. Remove the lower intake manifold bolts. 17. Remove the lower intake manifold. 18. Remove the valve rocker arms and pushrods. 19. Remove the lower intake manifold gaskets and seals. 20. Clean the lower intake manifold gasket mating surfaces. 21. Remove and clean all the RTV sealant from the lower intake manifold and the engine block (1).

Related entry:

2002 impala intake manifold removal, 1997 chevy monte carlo z34 heater pipe o-ring, manifold removal for 1999 gmc yukon, lower intake manifold gasket 5 3 chevy, exhust manafol bolt pattern 2003 impala, exhaust manifold bolt pattern 2003 impala, e46 Heater inlet pipe torque, 5 3 Intake Manifold Gasket Replacement, 2002 impala intake manifold torque specs, 2002 ford ranger 4 0 torque spec lower intake,

Ford 429 460 514 V8 Engine Specs-Torque Specs-Cylinder Numbering-Firing Order-Distributor Rotation

0

Filed Under (Ford) by admin on 23-04-2010

download
Torque Specs always torque bolts in three equal increments Lube or Sealer Torque to: Engine Oil 105 ft-lbs. Connecting Rod Bolts Engine Oil 45 ft-lbs. Engine oil 140 ft-lbs. (blind hole) (water jacket) Rocker Arms (non-adjustable) Engine Oil 20 ft-lbs. Engine Oil 25 ft-lbs. Engine Oil 15 ft-lbs. Cam Bolt (upper gear) Thread Locker 45 ft-lbs. Engine Oil 20 ft-lbs. Non- Hardening 30 ft-lbs. Sealer Engine Oil 10 ft-lbs. Flexplate (Automatic) Thread Locker 85 ft-lbs.

Related entry:

alignment specs online free, torque for 2006 vw tdi rear wheel axle, 07 cx-7 head bolt torque, 2003 chev impala torque specs, free alignment specs, 05 chevy aveo head bolt torque diadram, corvette tune up specs 1962, toyota 2e connecting rod torque specs, tork manafol 2003 impala, 2001 intrepid camshaft torque,