03 nissan altima nats


You are searching repair manual in PDF format about 03 nissan altima nats use another keyword for search another post or files



  03 nissan altima nats Direct Download speed 5787 Kb/s

  03 nissan altima nats Full Version speed 6767 Kb/s




2004 Nissan Quest Antitheft System – Vehicle No Start

0

Filed Under (Nissan) by admin on 21-09-2010

download
ENGINE WILL NOT START NVIS/NATS SYSTEM DESCRIPTION/KEY REGISTRATION This version of NTB03-031 amends the Applied Vehicles. Please discard all paper copies of the earlier versions. APPLIED VEHICLES: 2005 and later Altima (L31), Pathfinder (R51), Frontier (D40), Xterra (N50), 350Z (Z33) 2004 and later Maxima (A34), Quest (V42), Armada (TA60), Titan (A60), Murano (Z50) 2004 350Z (Z33) built after the following:NOTE: ^ For 2003 Murano, and 2003-2004 350Z built before the above Date and VIN’s, see NTB02-071 ^ This bulletin does NOT cover 2002-2004 Altima. SERVICE INFORMATION ^ This bulletin covers the latest version of the Nissan Vehicle Immobilizer System/Nissan Anti-Theft System (NVIS/NATS). This system, referred to as “NATS”, is standard equipment on the Applied Vehicles listed above. ^ This version of NATS uses advanced anti-theft functions which are “password protected”. This helps prevent “unauthorized access” into the NATS registration procedure. ^ To obtain the password from ASIST, first use CONSULT-II to get the “BCM-specific” 5-digit number (PIN) code from the vehicle. ^ Unlike earlier NATS systems, this NATS system DOES NOT need to be Re-Initialized if the Electronic Control Unit (ECM) is replaced. NOTE: The ECM and Body Control Module (BCM) do work together, but the BCM in this system controls the information necessary to “tell” the ECM to start the vehicle. IMPORTANT: The NATS Procedure in this bulletin is for the Applied Vehicles only. Do not use this procedure on other NATS-equipped vehicles.

Related entry:

removing immobolization ring on 2005 ALTIMa, 2005 NISSAN XTERRA nvis reset, 1995 nissan quest obd location, service bulletin for 2004 nissan altima blend, nissan serena 2003 lights, nissan murano 2004 code p0300, nats nissan altima, how to replace nvis (nats)immu, Engine Code P0420 on 2004 Nissan Murano, charging ac 2007 nissan frontier,

2003 – 2005 Nissan Altima 2004 Nissan Maxima ENGINE IS HARD TO START WHEN WARM

0

Filed Under (Nissan) by admin on 04-06-2010

download
The engine is hard to start when warm, but starts OK when the engine is cold. NOTE: “Hard start” is engine crank time that is longer then 3 seconds. • If you only have DTC P0340, replace only Bank 1 CMP (Camshaft Position) Sensor. • If you only have DTC P0345, replace only Bank 2 CMP (Camshaft Position) Sensor. • If you have both codes, replace both sensors. • For a “hard to start warm” incident, replace both sensors, even if you have no codes. Refer to sections EC and EM in the correct Service Manual for sensor replacement information. If replacement of the sensors does not solve your incident, go back to ASIST for further diagnostic and repair information.

Related entry:

2 5 Nissan Engine cam removal, 2003 NISSAN MAXIMA AIR BAG CODE B1035, 05 nissan cam cap, remove headlight assembly from 2007 nissan altima, location of tmc in 98 altima, LOCATION OF THE ECM ON A 2004 NISSAN MAXIMA, how to replace ac compressor pulley 2005 nissan altima, how to install an immobilizer on a 2004 NISSAN maxima, change headlight on 2001 nissan altima, 2011 altima reprogramming engine control module,

2005 – 2009 Nissan FRONTIER, Nissan XTERRA, Nissan PATHFINDER, FRONT AIR BAG CRASH ZONE SENSOR

0

Filed Under (Nissan) by admin on 04-01-2011

download
SERVICE PROCEDURE 1. Set the parking brake. 2. Connect C-III to the vehicle. 3. Use C-III to check for Air Bag DTCs. a. Navigate C-III to Air Bag Direct Diagnostic Mode. b. Make sure to check both SELF DIAG RESULTS and SELF-DIAG [PAST]. • SELF-DIAG [PAST] is under Special function. • If there are any DTCs stored for AIR BAG other than B1033, B1034 and/or B1035, perform repairs as needed, and then erase DTC before continuing with this procedure. • Diagnosis and repair for DTCs other than B1033, B1034, and/or B1035 is not covered by this bulletin. NOTE: All DTCs (except B1033, B1034, and B1035) must be repaired and erased before continuing with this procedure. 4. Disconnect C-III from the vehicle. 5. Start the engine and let it idle for about 5 seconds. 6. Turn the ignition OFF. 7. WARNING: Prep the vehicle for Crash Zone Sensor replacement as follows: The following are VERY IMPORTANT to prevent unexpected air bag deployment. • Remove the ignition key / Intelligent Key from the cabin of the vehicle and set aside, away from the vehicle (this will prevent accidentally turning the ignition ON). • Make sure the ignition remains OFF until after the new sensor is completely installed. • Make sure no one is in the vehicle cabin and no one enters the vehicle cabin until after the sensor is completely installed. • Wait for all control units to “power down” (at least 1 minute) before continuing. 8. Locate the Crash Zone Sensor (see Figure 2). Crash Zone Sensor Cover 9. Remove the 2 Crash Zone Sensor nuts shown in Figure 3. • Discard these nuts. They will not be reused. 10. Remove the Crash Zone Sensor Cover. 11. Disconnect the electrical connector shown in Figure 4.

Related entry:

2001 Nissan pathfinder will not idle after replacing battery, nissan serena c25 service manual, 06 nissan presage manual, Manual Nissan Cabstar, procedure for changing nissan wingroad ECU, abay e25 nissan full gasket set, AIRBAG LIGHT IS BLINKING ON NISAN TIIDA WHAT IS WRONG, AIRBAG LIGHT ON NISSAN TIIDA IS BLINKING WHAT IS WRONG, how to replace a nissan serena c25 camshaft sensor, operations of nissan sentra 1990 carburetor,

2002-2004 Nissan Altima W/QR25 ENGINE; NO-START AFTER ‘COLD SOAK’

0

Filed Under (Nissan) by admin on 29-11-2010

download
IF YOU CONFIRM • After a ‘cold soak’,* the engine cranks (turns with starter), but does not start. *Cold soak: Engine has cooled down to ambient (outside) temperature, regardless of summer or winter seasonal variations. • The engine may start if it is cranked for an extended period (more than 5 seconds) or if the throttle is opened during cranking. • After starting and operating for a few minutes the engine runs normally. ACTIONS • Replace the starter motor. • Add 1 can of Nissan Fuel System Cleaner into the fuel tank. • Perform ECM Part Number Check to see if the vehicle you are working on needs ECM Reprogramming. • Perform ECM Reprogramming, if needed. SERVICE PROCEDURE Replace Starter, Add Cleaner 1. Replace the starter motor. • Use the part number from the Parts Information section of this bulletin. • Refer to section SC, “STARTING SYSTEM, Removal and Installation” in the applicable Nissan Electronic Service Manual (ESM). 2. Add one full can of Nissan In-Tank Fuel System Cleaner to the fuel. NOTE: If the fuel tank is less than ¾ full, instruct the customer to fill the tank as soon as it is convenient after the repair. Driving with the Cleaner installed and low fuel level will not harm the fuel system or engine, but will reduce the effectiveness of the cleaning process. 3. Continue to ECM Part Number Check (next page).

NISSAN PERIODIC MAINTENANCE SCHEDULE NISSAN MICRA

0

Filed Under (Nissan) by admin on 11-04-2010

download
ENGINE MAINTENANCE (Petrol Engine) Replace engine oil Replace engine oil filter Inspect drive belts Inspect cooling system
Page 1© NISSAN NISSAN PERIODI CMAINTENANCE SCHEDULE NISSAN MICRA 15,000 KM Inspect brake, clutch and automatic
trans-axle fluids Inspect manual trans-axle gear oil Inspect power steering fluid and lines Inspect brake, clutch and exhaust systems
Inspect steering gear and linkage, axle and suspension parts and front driveshafts Inspect wheel alignment (if necessary rotate
tyres and balance Inspect brake pads, rotors and other brake components Inspect brake linings, drums and other brake
components Inspect foot brake, parking brake and clutch Lubricate locks, hinges & hood latch Inspect seat belts, buckles, retractors,
anchors & adjuster Clean or replace ventilation filter Replace brake fluid (Severe conditions only)

Related entry:

nissan caravan ZD30 - 194794A 2004 Electrical manual, replacing micra interior light, NISSAN MICRA 1 2 2007 SERVICE SCHEDULE, where is nats system located on nissan micra petrol, intelligent key for y11 wingroad 2004 make, nissan micra bcm repairs, replacing micra aerial, Torque Settings for micra k12 cylinder head bolts, WHAT TIP OF ENGINE OIL FOR 1500CC NISSAN WINGROAD Y12,