07 equinox lt rear wiper motor
You are searching repair manual in PDF format about 07 equinox lt rear wiper motor use another keyword for search another post or files
07 equinox lt rear wiper motor Direct Download speed 5787 Kb/s
07 equinox lt rear wiper motor Full Version speed 6767 Kb/s
Filed Under (Buick) by admin on 18-11-2010
1. Remove the rear wiper arm (5). 2. Remove the rear wiper motor drive shaft nut (6). 3. Remove the washer (7) and seal (8) from the wiper motor drive shaft. 4. 5. 6. 7. 8. Remove the liftgate trim panel. Disconnect the electrical connector (1) from the rear wiper motor. Remove the rear wiper motor screws. Remove the rear wiper motor (3) from the liftgate (5). Remove the rear wiper motor from the vehicle. Installation Procedure 1. Position the rear wiper motor (3) to the liftgate. Notice: refer to Fastener Notice. 2. Install the rear wiper motor screws. Tighten the screws to 6 N.m (53 lb in ). 3. Connect the electrical connector (1) to the wiper motor. 4. Install the washer (7) and seal (8) onto the rear wiper motor drive shaft. 5. Install the rear wiper motor drive shaft nut (6). Tighten the nut to 6 N.m (53 lb in ). 6. Install the rear wiper arm. 7. Inspect rear wiper for proper operation. 8. Install the liftgate trim panel.
Related entry: 68 c10 winshiel wiper wiring
Filed Under (Suzuki) by admin on 15-06-2010
A 2-speed wiper motor with intermittent mode is standard on all models. A 3-speed wiper motor is optional on some models. Washer system uses a reservoir-mounted electric pump located in the engine compartment. A one-speed rear wiper/washer is optional. Rear wiper/washer switch is located on instrument panel, to right of steering column. Wiper switch has 2 positions, rear wiper ON or OFF. Washer and wiper switch has 3 positions, OFF, washer ON (depressed half way), or washer and wiper ON (fully depressed). Washer/wiper switch moves to OFF position when switch is released. TESTING NOTE: If wiper malfunctions or does not return to park position,check for blown fuse, faulty wiper motor, control switch or connections. If washer malfunctions, check for clogged hose or nozzle, faulty washer motor, control switch or wiring. FRONT WIPER MOTOR REAR WIPER MOTOR INTERMITTENT WIPER RELAY WIPER/WASHER SWITCH WIPER MOTOR BRUSH & COMMUTATOR REMOVAL & INSTALLATION WIPER MOTOR WIRING DIAGRAMS
Related entry: kia spectra washer pump wiring
Filed Under (Ford) by admin on 02-03-2011
Removal 1. Raise vehicle on hoist. Refer to Section 00-02. 2. Remove rear wheel and tire assembly. 3. Remove rear stabilizer bar link and bushing link nuts at both ends of rear stabilizer bar (5A772) . Rotate bar up and out of the way. 4. Disconnect parking brake rear cable and conduit (2A635) at rear disc brake caliper (2553) . 5. Install three Rotunda Spring Cages 086-00031 or equivalent to rear spring as follows: a. Install one spring cage without an adjuster link to the inboard side (the innermost “bend” of the rear spring (5560) ). b. Install two more spring cages, with adjusters, at 120 degree angles to the previously installed cage. Spring, Rear 6. Place a transmission jack or suitable stand under the rear suspension arm and bushing (5500) as far outboard as possible. 7. Support the rear wheel knuckle (5A969) assembly by wiring the rear suspension arm and bushing to the body. 8. Remove lower rear shock absorber mounting bolt, washer and nut. 9. NOTE: Rear suspension arm and bushing must not be lowered until pivot bolts are loose. Do not attempt to remove plastic cap on front pivot nut. Loosen both inboard pivot bolts on rear suspension arm and bushing . 10. Remove two bolts and nuts retaining rear suspension arm and bushing to rear wheel knuckle . 11. Lower the rear suspension arm and bushing by lowering jack. Ensure spring cages properly seat on rear spring as rear suspension arm and bushing is dropped. 12. Remove jack, lower rear suspension arm and bushing down fully by hand and remove rear spring with cages in place. 13. Remove rear spring center mounting insulators (5741) , if necessary. 14. If spring cages are to be removed for installation on rear spring , use Coil Spring Compressor D78P-5310-A or equivalent to compress rear spring and remove cages. Rear spring center mounting insulator should be installed on rear spring before installing rear spring in tool to prevent slipping of plates.
Related entry: 1995 ford f 750 axle
, how to replace the rear wheel bearing on a 2011 jeep compass
, hyundai santa fe rear hatch will not open 2007
Filed Under (Audi) by admin on 23-03-2011
Special tools, testers and auxiliary items required Removal lever 80-200 Removing Note: In order to prevent potential damage to wiper arms, the windshield wipers will not function, or will cease functioning should the front hood be opened. If Wiper Motor Control Module J400 is to be replaced, connect VAS 5051/5052 and initiate OBD program. option “J400 – replacing” Switch on ignition. Actuate touch-wipe function and allow wiper motor to move to end position. CAUTION! Switch off all electrical consumers. Switch ignition off and remove ignition key. Use screwdriver to pry off wiper arm caps. Loosen nuts – arrows – (do not remove). Loosen wiper arms from wiper shaft by tilting slightly, remove nuts and remove wiper arms. Unclip washer jets – arrow – . Push washer jet (with hoses connected) through mounting opening into plenum chamber. Pull off rubber seal – 1 – for plenum chamber cover. Remove plenum chamber cover – 2 – . Note: Use adhesive tape to prevent fender from becoming scratched.
Filed Under (Toyota) by admin on 30-07-2010
1. REMOVE FR WIPER BLADE LH a. Raise the front wiper blade to the position as shown in the illustration. b. Disengage the claw and remove the front wiper blade LH from the front wiper arm LH. NOTE: Do not bend the front wiper arm with the front wiper blade LH removed, as the arm tip could damage the windshield surface. 2. REMOVE WIPER RUBBER LH a. Remove the front wiper rubber LH from the front wiper blade. b. Remove the 2 wiper rubber backing plates from the wiper rubber LH. 3. INSTALL WIPER RUBBER LH a. Install the 2 wiper rubber backing plates onto the wiper rubber LH. NOTE: Be sure to install the wiper rubber backing plates in the correct direction. b. Install the wiper rubber LH so that the head part (Larger side) of the wiper rubber faces the arm axle side. NOTE: Push the front wiper blade into the grooves of the wiper rubber to engage them completely.
Related entry: bmw x5 wiper problems