1974 chevy van


You are searching repair manual in PDF format about 1974 chevy van use another keyword for search another post or files



  1974 chevy van Direct Download speed 5787 Kb/s

  1974 chevy van Full Version speed 6767 Kb/s




1995 Chevrolet Chevy Van G20 Exploded View Of 4L60-E Transmission Internal Components

0

Filed Under (Chevrolet) by admin on 02-05-2010

download
OVERHAUL – 4L60-E Fig. 16: Exploded View Of 4L60-E Transmission Internal
Components GENERAL MOTORS CORP.
1995 Chevrolet Chevy Van G20

Related entry:

free owners manual 1994 Chevy G20 Van Accessories, Free service manual for 1995 chevy g20 van, 94chevy g20 motor sensors, how to release freon from 2011chevy equinox, which hose do i use to recharge ac 2011 chevy cruze, manual for 1995 Chevrolet Van G20, 84 Chevy Van 20, 84 chevrolet g20 van door wiring diagram, 1996 tahoe AC fan resistor replacement, 1994 chevy g20 conversion van parts,

2005 Chevy Astro Van Wheel Speed Sensor Replacement (RWD) Removal Procedure

0

Filed Under (Chevrolet) by admin on 15-09-2010

download
1. Raise and support the vehicle. Refer to Vehicle Lifting. 2. Remove the tire and wheel. 3. Remove the brake rotor (2). Refer to Brake Rotor Replacement – Front. 4. Important: The wheel speed sensor mounts to the hub/bearing assembly. Thoroughly clean around this area in order to prevent any dirt or contaminants from entering the sealed wheel bearing. Failure to do this may lead to premature wheel bearing failure. Remove the Wheel Speed Sensor (WSS) mounting bolt. 5. NOTICE: Carefully remove the sensor by pulling it straight out of the bore. DO NOT use a screwdriver, or other device to pry the sensor out of the bore. Prying will cause the sensor body to break off in the bore. Remove the wheel speed sensor (5) from the hub/bearing assembly (4). Remove the WSS cable mounting clip from the knuckle. Remove the WSS cable mounting clip from the upper control arm. Remove the WSS cable mounting clip from the frame attachment point. Remove the WSS cable electrical connector. 6. 7. 8. 9. Installation Procedure 1. Plug the WSS bore to prevent debris from falling into the hub. 2. Using a wire brush or equivalent, clean the WSS mounting surface on the hub to remove any rust or corrosion. 3. Apply a thin layer of wheel bearing lubricant, GM P/N 01051344 to the hub surface and the sensor O-ring prior to the sensor installation.

Related entry:

2002 astro encoder motor install,

2006 Chevy Avalanche 1500 Fan Clutch Replacement

0

Filed Under (Chevrolet) by admin on 26-08-2010

download
Removal Procedure 1. Remove the upper fan shroud. 2. Install the J 46406 and the J 41240-5A to the fan clutch. 3. Remove the fan hub nut from the water pump in a counterclockwise rotation. 4. Lay the fan blade face down on a workbench. 5. Remove the fan clutch bolts from the rear of the fan blade. 6. Separate the fan clutch from the fan blade. Installation Procedure 2006 Chevy Truck Avalanche 1500 2WD V8-5.3L VIN T 1. Install the fan clutch bolts. 2. Install the fan clutch onto the fan blade. Notice: Refer to Fastener Notice in Service Precautions. 3. Install the fan clutch bolts. ^ Tighten the bolts to 23 Nm (17 ft. lbs.). 4. Install the fan blade. 5. Install the J 46406 and the J 41240-5A to the fan clutch. ^ Tighten the fan clutch nut clockwise to 56 Nm (41 ft. lbs.). 6. Install the upper fan shroud.

Related entry:

2005 chevy silverado 1500 ac fan troubleshooting,

1996 Chevrolet Chevy C Pickup Fuel System Diagnosis (System Check)

0

Filed Under (Chevrolet) by admin on 20-01-2011

download
Circuit Description When you turn ON the ignition switch, the Vehicle Control Module (VCM) turns ON the in-tank fuel pump. The pump remains ON as long as the engine is cranking or running and the VCM is receiving reference pulses. If there are no reference pulses, the VCM shuts the fuel pump OFF within 2 seconds after the ignition was switched to the ON position or if the engine stops. The VCM will also turn ON the fuel pump for 2 seconds when the ignition is turned to the OFF position. An electric fuel pump pumps the fuel through an in-line filter to the Central SFI unit. The pump is attached to the fuel level meter assembly inside of the fuel tank. The pump is designed to provide fuel pressure above what is needed by the fuel injectors. The pressure regulator keeps the fuel available to the injectors at a regulated pressure. Unused fuel is returned to the fuel tank by the fuel return pipe. Diagnostic Aids Tools Required • J 34730-1A Fuel Pressure Gage in J 34730-E or • J 34730-1A Fuel Pressure Gage with J 34730-250 Fuel Pressure Adapter Kit. Test Description The numbers below refer to the step numbers on the diagnostic table. 2. Wrap a shop towel around the fuel pressure connection to absorb any small amount of fuel leakage that may occur when installing the fuel pressure gauge. Turn ON the ignition, the fuel pressure should be 415-455 kPa (60-66 psi) for the Central SFI and 385-430 kPa (56-62 psi) for

Related entry:

1989 caprice fuel tank pressure hose, j-34730-e,

1995 Chevy Lumina APV Engine Control Module: Service and Repair

0

Filed Under (Chevrolet) by admin on 28-08-2010

download
CAUTION: To prevent possible Electrostatic Discharge damage to the Powertrain Control Module (PCM), Do Not touch the connector pins or soldered components on the circuit. Service of the PCM should normally consist of either replacement of the PCM or a Programmable Read Only Memory (PROM) change. If the diagnostic procedures call for the PCM to be replaced, the engine calibrator (PROM) and PCM should be checked first to see if they are the correct parts. If they are remove the PROM from the faulty PCM and install it in the new service PCM. THE SERVICE PCM WILL NOT CONTAIN A PROM. Diagnostic Trouble Code (DTC) 51 indicates the PROM is installed improperly or has malfunctioned. When DTC 51 is obtained, check the PROM installation for bent pins or pins not fully seated in the socket. If the PROM is installed correctly and DTC 51 still shows, replace the PROM. Important: When replacing the production PCM with a service PCM (controller), it is important to transfer the Broadcast code and production PCM number to the service PCM label. Please do not record on PCM cover. This will allow positive identification of PCM parts throughout the service life of the vehicle. CAUTION: To prevent internal PCM damage, the ignition must be “OFF” when disconnecting or reconnecting power to PCM (for example, battery cable, PCM pigtail, PCM fuse, jumper cables, etc.). REMOVE OR DISCONNECT 1. Negative battery cable. 2. Right side sound insulator. 3. Vacuum center. 4. Connectors to PCM. 5. PCM. 6. PROM access cover. 7. PROM from PCM. INSTALL OR CONNECT 1. PROM to PCM. 2. PROM access cover. 3. PCM. 4. Connectors to PCM. 5. Vacuum center. 6. Right side sound insulator. 7. Negative battery cable.

Related entry:

pcm adjustable 2001 chevy malibu, 03 isuzu npr 6 0l pcm location, removel of ecm from 03 chevy malibu, how to reset ecu computer for 2007 cobalt, ford explorer ac diode, 2012 Mustang GT Ford PCM Tear Tag location, 2006 crown vic pcm wiring diagram, 2005 ford focus pcm location and removal, 2004 cavalier pcm location, wiring schematics 2004 malibu classic 2 2L pcm,