1991 toyota corolla blower fan switch


You are searching repair manual in PDF format about 1991 toyota corolla blower fan switch use another keyword for search another post or files



  1991 toyota corolla blower fan switch Direct Download speed 5787 Kb/s

  1991 toyota corolla blower fan switch Full Version speed 6767 Kb/s




1991 Toyota Corolla Sedan BLOWER SPEED CONTROL SWITCH INSPECTION

0

Filed Under (Toyota) by admin on 05-07-2010

download
1. REMOVE BLOWER SPEED CONTROL SWITCH (a) Remove the illumination light from the A/C control assembly. (b) Using a screwdriver, pry loose the clip and push out the blower speed control switch to rear of the A/C control assembly. 2. INSPECT BLOWER SPEED CONTROL SWITCH CONTINUITY If continuity is not as specified. replace the blower speed control switch. 1991 Toyota Corolla Sedan L4-1587cc 1.6L DOHC (4A-GE) Vehicle Level Heating and Air Conditioning Blower Motor Switch Service and Repair Service and Repair BLOWER SPEED CONTROL SWITCH INSPECTION

Related entry:

2002 corolla speedometer too fast, 2006 toyota corolla s fan speed switch, 1991 toyota camry cooling diagram, 2006 Ford taurus speed control symtom chart, free Kia rio 1 3 dc installation diagram dc electric,

2004 Honda Element EX ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH)

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Check the engine oil level. Is the level OK? YES- Go to step 2 . NO- Adjust the engine oil to the proper level, then go to step 14 . 2. Turn the ignition switch ON (II). 3. Clear the DTC with the HDS. 4. Do the VTEC TEST in the INSPECTION MENU with the HDS. Is the result OK? YES- Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch) and the ECM/PCM. NO- Go to step 5 . 5. Check the result of step 4 . Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Failure Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Open Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) SIG Line Open Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) GND Line Open Is the test result any of the above? YES- Go to step 6 . NO- Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch). If it is OK, replace the rocker arm oil control solenoid (VTEC solenoid valve) (see step CMP SENSOR A REPLACEMENT ), then go to 14 . 6. Turn the ignition switch OFF. 7. Disconnect the rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector. 8. Check for continuity between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminals No. 1 and No. 2.

Related entry:

where is the oil pressure relief valve situated on ford mondeo 2002, peugeot 307 gearbox oil pressure regulation, Blower BMW E36 1991, air solenoid valve on international 8600 not working properly, 2007 ford fusion ac pressure switch location, 2007 element rocker arm oil pressure switch, replace ignition switch 2007 jeep liberty, diagram of windshield wiper relays for1994 honda accord, oil pressure light 2004 suburban, 2001 mford taurus rocker arm torque,

2002 Ford F 150 Cooling Fan – Blade, Clutch and Shroud Removal and Installation

0

Filed Under (Ford) by admin on 27-10-2010

download
WARNING: Do not run the engine while the protective components are removed. Failure to follow these instructions may result in personal injury. All vehicles 1. Remove the air cleaner assembly. 2. Drain the cooling system. Supercharged vehicles 3. Remove the supercharger degas bottle. All vehicles 4. Remove the front air deflector. 1 Remove the pin-type retainers. 2 Remove the front air deflector. 5. Remove the upper hose from the radiator. 1 Release the clamp. 2 Disconnect the hose. 6. Remove the degas bottle hose from the radiator. 1 Release the hose clamp and slide it away from the end of the hose. 2 Slide the overflow hose off the radiator fitting. 7. Remove the fan blade assembly and fan clutch. 1 Use the fan pulley holding wrench to hold the water pump pulley steady. 2 Use the fan clutch nut wrench to remove the fan blade and the fan clutch. 7. Remove the fan blade assembly and fan clutch. 1 Use the fan pulley holding wrench to hold the water pump pulley steady. 2 Use the fan clutch nut wrench to remove the fan blade and the fan clutch. 9. NOTE: If the lead retaining clip is broken, install a new lead retaining clip. If equipped, disconnect the fan clutch electrical connector and lead retaining clip. 10. Remove the fan blade and fan shroud out of the vehicle together. 11. Remove the bolts and separate the fan blade assembly from the fan clutch. 12. NOTE: To avoid stripping the threads, use the correct bolts when installing a new fan clutch. Use’ bolts 575632-S426 for fan clutch F85A-8A616 and bolts N602548-S426 for fan clutch 2L34-8A616 and 2C64-8A616. To install, reverse the removal procedure.

Related entry:

1984 corvette radiator fan fuse, 97 ls400 fan idler bracket change, fuse panel e450 2007 fan, 2002 dodge durango blower motor is still running after key is turned off, fan blower 04dodge 3500 eratic, ford e450 blower motor fuse location, holden rodeo blower resister, how to change the fan switch 2002 E350, how to replace a fan switch on a f 250 2002, how to take off fan on 2008 6 4 F250,

2004 Chevy Silverado 3500 Fan Clutch: Service and Repair Fan Clutch Replacement

0

Filed Under (Chevrolet) by admin on 20-08-2010

download
Removal Procedure 1. Remove the upper fan shroud. 2. Install the J 46406 to the fan clutch. 3. Remove the fan hub nut from the water pump in a counterclockwise rotation. 4. Remove the fan clutch bolts from the rear of the fan blade. 5. Separate the fan clutch from the fan blade. Installation Procedure 1. Install the fan clutch bolts from the rear of the fan blade. 2. Notice: Refer to Fastener Notice in Service Precautions. Install the fan clutch bolts. Tighten the bolts to 23 Nm (17 ft. lbs.). 3. Install the fan assembly. 4. Install the J 46406 to the fan clutch. Tighten the nut clockwise to 56 Nm (41 ft. lbs.). 5. Install the upper fan shroud.

Related entry:

e90 fan, e90 fan bolt up, how do i get the fan off of my 2004 chevy suburban?, installation diagram for 2004 pajero 3 8 v6 fan belt, remove fan clutch on 04 suburban, where is fan blade motor on s 2004 chevy suburban,

2005 Buick Allure Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off

0

Filed Under (Buick) by admin on 17-12-2010

download
Condition Some customers may comment on an inoperative or intermittent Heating, Ventilation and Air Conditioning (HVAC) blower motor. Others may comment that the blower motor speed may momentarily drop or that the blower motor continues to run after the key is turned off. Cause This condition may be caused by a voltage spike from the wiper motor. The voltage spike may cause a logic lock up in the blower motor control module that may be either momentary or permanent. Correction DO THIS DON’T DO THIS Install a Capacitor at the Blower Motor Control Module Connector Technicians are to install a capacitor, P/N 25073556, at the blower motor control module connector using the following procedure: 1. Disconnect the negative cable from the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 2. Remove the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement-Right procedure in the Instrument Panel, Gages and Console section of SI. DO NOT replace the Blower Motor Control Module, Blower Motor or the HVAC Control Head

Related entry:

how to change front blower motor 2007 grand caravan, 2007 grand caravan sxt blower motor noise, 2005 F250 blower motor relay location, ELECTICAL WIRING DIGRAM FOR 2003 HONDA ACCORD DN 2 3, 2003Astro van air andheater controls repair fix, diagram wiring for 1999 lhs ac blower, blower motor relay honda crv 2004, how to replace a manual heater switch on a 2004 sonata, diagrahm of 2004 pontiac vibe blower motor removal, replacing ac blower motor on an 9900 international,