1992 ford f 250 fuse


You are searching repair manual in PDF format about 1992 ford f 250 fuse use another keyword for search another post or files




2005 Ford Expedition, Ford F-250, Ford F-350 TICKING AND/OR KNOCKING NOISE FROM ENGINE

0

Filed Under (Ford) by admin on 07-09-2010

download
FORD: 2005 Mustang 2004-2005 F-150 2005 Expedition, F-250, F-350 This article supersedes TSB 05-15-8 to update the Service Procedure. ISSUE Some vehicles equipped with a 4.6L 3-valve or 5.4L 3-valve engine may exhibit a ticking and/or knocking noise after reaching normal operating temperature. The noise may be described as “ticks”, “taps”, “knocks”, or “thumps”. In some cases the noise may be a normal characteristic of these engines. In other cases the noise may require further investigation. Sorting out and defining the noise as reported by the customer is important to successfully diagnose and/or repair the condition. ACTION Before starting diagnosis, it is critical to determine the specific engine noise the customer is concerned with. The customer should be interviewed to get their detailed perception and description of the noise, and to determine if the noise occurs at idle or above idle speed, and if the engine is cold, hot, or both. Attempt to duplicate the noise, and determine the source of the symptom. Refer to the following Service Procedure to help determine the source of the noise and if a repair is needed. LINCOLN: 2005 Navigator PRE-CHECKS 1. 2. 3.

Ford / Mercury / Lincoln Band-Mounted Sensor Re-Learn Instructions

0

Filed Under (Ford, Lincoln) by admin on 17-10-2009

The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford Escape / Mercury Mariner 2007-2009 Ford Expedition / Lincoln Navigator 2006-2009 Ford Explorer / Lincoln Aviator / Mercury Mountaineer 2007-2008 Ford F150, F250, and F350 / Lincoln Mark LT
2009 Ford Flex 2008-2009 Ford Focus 2006-2007 Ford Freestar / Mercury Monterey 2008-2009 Ford Fusion / Lincoln MKZ / Mercury Milan 2007-2009 Ford Mustang 2007-2009 Ford Ranger 2008-2009 Ford Taurus / Mercury Sable

1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard). 2. Turn the ignition switch to OFF then press and release the brake pedal. 3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds. 4. Press and release the brake pedal

download

1993 Dodge Dakota FUSE PANEL IDENTIFICATION (1992-95 MODELS)

0

Filed Under (Dodge) by admin on 26-05-2010

download
Fig. 1: Fuse Block Identification (1992-95 Models) Courtesy of CHRYSLER CORP. FUSE & CIRCUIT BREAKER I.D. (UNDER INSTRUMENT PANEL) 1 – 30 Amp (Green) A/C Or Heater Blower Motor. 2 – 30 Amp (Circuit Breaker) Power Windows. 3 – 10 Amp (Red) (1992-93); 15 Amp (Lt Blue) (1994-95) Back-Up Lights, A/C Electronic Cycling Switch (1992-93); Back-Up Lights, Airbag Module, Overhead Console (1994-95). 4 – Not Used (1992); 5 Amp (Tan) (1993-95) ABS Brake System. 5 – 20 Amp (Yellow) Power Door Locks. 6 – 15 Amp (Lt. Blue) Horn, Tachometer. 7 – 10 Amp (Red) Anti-Lock Brake Module, Stoplights, Buzzers. 8 – 20 Amp (Yellow) Taillights, Park, Side Marker Lights, Clock & Radio Display Intensity, License & Panel Lights.

2002 Ford F 250 2WD Super Duty Ford 10.5 Inch Full-Floating Rear Drive Axle Removal and Installation

0

Filed Under (Ford) by admin on 30-07-2010

download
Axle Shaft Removal 1. NOTE: The wheels and tires do not have to be removed in order to remove the axle shafts. Loosen and remove the retaining bolts. 2. Remove the axle shaft. 3. Inspect the axle shaft O-ring seal for cracks, nicks or wear and replace it if required. Installation NOTE: Lubricate the O-ring seal with lubricant prior to installation of axle shaft. 1. Install the axle shaft. 2. NOTE: Coat the threads of the retaining bolts with stud and bearing mount. Install the retaining bolts and tighten.

1999 Plymouth Truck Voyager Horn Will Not Sound

0

Filed Under (Plymouth) by admin on 13-05-2010

download
Check horn fuse 6 in the Power Distribution Center and fuse 7 in the Junction Block. If fuse is blown refer to FUSE BLOWN. If fuse is OK, refer to FUSE OK. Fuse Blown 1. Verify condition of battery terminals and voltage, refer to Battery If battery connections and battery charge is OK proceed to Step 2. . Using a voltmeter, test for battery voltage at both sides of horn fuse 7. If voltage is
OK, on both sides of fuse, proceed to Fuse OK. If voltage is OK, on one side of fuse, the fuse is blown, proceed to Step 3. 3. Using a suitable ammeter in place of the fuse, test amperage draw of the horn circuit. If amperage draw is greater than 20 amps without the horn switch depressed, a grounded circuit exists between the fuse and the horn relay Proceed to Step 4. If amperage draw is greater than 20 amps with the horn switch depressed, a grounded circuit exists between the horn relay and the horn. Proceed to step Step 5. 4. Remove the horn relay from the Junction Block. If the amperage draw drops to 0 amps , the horn switch or circuit is shorted. If the amperage draw does not drop to 0 amps , repair short at the Junction Block.