1994 Chevrolet Z71 pickup
You are searching repair manual in PDF format about 1994 Chevrolet Z71 pickup use another keyword for search another post or files
1994 Chevrolet Z71 pickup Direct Download speed 5787 Kb/s
1994 Chevrolet Z71 pickup Full Version speed 6767 Kb/s
Filed Under (Chevrolet) by admin on 14-11-2010
Model(s): 1994-95 Buick Regal 1994-97 Buick Skylark 1994-98 Buick Century 1994-95 Chevrolet Beretta Corsica, Lumina, Monte Carlo 1996-98 Chevrolet Venture 1997-98 Chevrolet Malibu 1993-97 Oldsmobile Cutlass Supreme 1994-96 Oldsmobile Cutlass Ciera 1994-97 Oldsmobile Achieva 1996-98 Oldsmobile Silhouette 1997-98 Oldsmobile Cutlass 1994-98 Pontiac Grand Am, Grand Prix 1996-98 Pontiac Trans Sport with 3100, 3400 V6 Engine (VINs M, E – RPOs ticking type noise that begins shortly after cold engine start-up and gradually diminishes as the engine warms up. In most cases, the noise is gone after five (5) minutes. In severe cases, the noise may not disappear when lhe engine is hot. Under normal design tolerances when the piston pin bore is produced at the maximum tolerance and the piston pin is produced at the minimum tolerance (min-max tolerance) trace noise levels can occur. This level of noise does not affect the reliability or durability of the product. If piston-to-pin noise is detected and the customer desires the condition to be corrected, replace all six pistons with pin assemblies. The new piston sets have a minimal piston-to-pin clearance. Remember, piston-to-pin noise occurs in both park and drive at engine idle rpm and it varies in intensity depending on the number of pistons involved. A ticking sound means one piston is affected whereas a rattle or diesel type sound indicates more than one piston affected. The following should also be checked: 1. On W-Cars, make sure the right side engine splash shield is not contacting the engine crankshaft balancer. This condition usually happens cold and is caused by the shield curling when cold. 2. Reference Service Bulletin 57-71-06 for transmission rattle noise often confused for engine rattle noise. 3. Reference Service Bulletin 47-61-36 for Accessory Drive Belt Tensioner noise. 4. Check cylinder bore diameter and piston diameter as outlined in the Service Manual.
Filed Under (Oldsmobile) by admin on 11-06-2010
1993 Chevrolet Camaro 3.4L 1995 Chevrolet Camaro 3.4L, Vin S 1994 Buick Skylark Custom 3.1L, Vin M, 1995 Chevrolet Lumina 3.1L Eng Cfg V6 1994 Chevrolet Corsica 3.1L, Vin M, Eng 1995 Pontiac Grand AM SE 3.1L, Vin M, Cfg V6 Eng Cfg V6 1994 Oldsmobile Cutlass Supreme S 3.1L, 1995 Pontiac Grand Prix SE 3.1L Vin M DTC 77. 1. Remove the throttle body, and inspect the Exhaust Gas Recirculation Valve (EGR) port in the intake plenum. 2. The passage plugs at the bottom where it dumps into the plenum. 3. Best to use an old speedometer cable in a drill to run inside the passage to knock all the carbon out. Restricted Exhaust Gas Recirculation (EGR) Passages When an EGR solenoid is activated by the Powertrain Control Module (PCM), the PCM monitors the change in the Manifold Absolute Pressure (MAP) reading. Carbon deposits anywhere in the EGR passageways will set this code.
The following diagnostics might be helpful if the vehicle exhibits the conditlon(s) described above. Use the appropriate recommendation based on what symptom has occurred. Recommendation/Instructions No DTCs Review Corporate Bulletin Number 05-02-32-002B to assure you do not have a blown 60 amp steering fuse. The fuse can be blown during improper jump starting of the vehicle on the HHR and ION. Check for this particularly for tow in conditions. DO NOT replace the steering column unless an internal short has been Identified in the column that is causing fuse to blow. Power Steering Warning Message on DIC with DTCs C0176 and C0476 This condition is often the result of excessive lock-to-lock turns of the steering wheel, causing the thermal protection in the Power Steering Control Module (PSCM) to take the steering motor temporarily off line. This is a normal operating characteristic of the system. DO NOT replace the steering column for this condition. Refer to Corporate Bulletin Number 06-02-32-002B for additional information
Filed Under (Chevrolet) by admin on 21-10-2010
Models: 2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission (RPOs MN3, MN7, M15, M76) Condition Some customers may comment on a 1-2 shift shudder at light to moderate acceleration. Typically, the throttle plate angle parameter is 12-20% at time of condition with vehicle speed of approximately 24-40 km/h (15-25 mph). The customer may describe the condition as slip or delayed shift into second. Correction Replace the complete second clutch assembly with service kit, P/N 24240561. Refer to the GM Unit Repair Service Manual for the year and model of the vehicle being serviced for the 2nd Clutch service procedure. This service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, other gaskets not included in this service kit will also be needed to complete the repair – a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering gasket kit 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to-Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve
Filed Under (Mercury) by admin on 10-06-2010
On all models, the fuse panel is located under the instrument panel, left of the steering column. Fig. 4: Interior Fuse Panel Identification (1994-95 Models) 1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid