1994 mercury Tracer, Trio
You are searching repair manual in PDF format about 1994 mercury Tracer, Trio use another keyword for search another post or files
Filed Under (Mercury) by admin on 10-06-2010
On all models, the fuse panel is located under the instrument panel, left of the steering column. Fig. 4: Interior Fuse Panel Identification (1994-95 Models) 1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid
Filed Under (Ford) by admin on 31-08-2009
repair and service manual covers Ford Escort and Mercury Tracer, all models, 1991-2000.
Table of Contents
About this manual | Introduction to the Ford Escort & Mercury Tracer | Vehicle identification numbers | Buying parts | Maintenance techniques, tools and working facilities | Jacking and towing | Booster battery (jump) starting | Automotive chemicals and lubricants | Conversion factors | Fraction/decimal/millimeter equivalents | Safety first! | Troubleshooting
Filed Under (Ford, Lincoln) by admin on 17-10-2009
The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford Escape / Mercury Mariner 2007-2009 Ford Expedition / Lincoln Navigator 2006-2009 Ford Explorer / Lincoln Aviator / Mercury Mountaineer 2007-2008 Ford F150, F250, and F350 / Lincoln Mark LT
2009 Ford Flex 2008-2009 Ford Focus 2006-2007 Ford Freestar / Mercury Monterey 2008-2009 Ford Fusion / Lincoln MKZ / Mercury Milan 2007-2009 Ford Mustang 2007-2009 Ford Ranger 2008-2009 Ford Taurus / Mercury Sable
1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard). 2. Turn the ignition switch to OFF then press and release the brake pedal. 3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds. 4. Press and release the brake pedal
Filed Under (Mazda) by admin on 10-10-2010
1994-1997 Ford Probe, Mazda MX3 with 4 cyl. & A/T 1994-2000 Mazda 626 with 4 cyl. & A/T 1998-2000 Mazda 626 with 6 cyl. & A/T 1995-2000 Ford Contour/Mercury Mystique with 6 cyl. & A/T 1999-2001 Mercury Cougar with A/T SUBJECT Vehicles with the Ford CD4E automatic transmission. CONDITION The driver’s side front CV axle has a 6-½ inch male inboard stub that fits into the transmission’s side gear. On the stub next to the housing seal surface is a carrier support surface that fits into the final drive sun gear inside the transmission (see figure 1). This sprocket assembly is chain driven with the reverse/overdrive sprocket by the planetary gear sets (see figure 2). The final drive sprocket assembly rides on the axle stub carrier support surface using a pressed, center bored bushing. This bushing wears the carrier support surface causing damage to the axle and eventually the transmission. SOLUTION If the carrier support surface of the axle being replaced appears rough and worn, then several possible failures need to be checked before replacing the axle or premature failure of the axle or possible damage to the transmission could occur. If the transmission’s internal oiling solenoid that lubricates this bushing fails, then the 2nd and 3rd gearshifts will not function. Although the Aftermarket lists this bushing, no tool exists to replace it. Ford only offer the bushing in a complete sprocket assembly making its replacement a very costly repair. The most common contributor to premature wear of this bushing is the vehicle not being within proper alignment specs. Without a four-wheel alignment, even though the front wheels may be centered to the rack, the rear thrust is pushing the front wheels causing stress on the front CV joints. The thrust forces acting on the front wheels while driving changes ALL the alignment specs resulting in the front wheels being in a constant turning action. This will wear the side gears and transmission seals as well as stressing this bushing. Another possible sign that alignment is affecting these items is a worn or torn inboard boot. Do not forget that worn motor mounts will also affect alignment thrust forces.
Filed Under (Oldsmobile) by admin on 11-06-2010
1993 Chevrolet Camaro 3.4L 1995 Chevrolet Camaro 3.4L, Vin S 1994 Buick Skylark Custom 3.1L, Vin M, 1995 Chevrolet Lumina 3.1L Eng Cfg V6 1994 Chevrolet Corsica 3.1L, Vin M, Eng 1995 Pontiac Grand AM SE 3.1L, Vin M, Cfg V6 Eng Cfg V6 1994 Oldsmobile Cutlass Supreme S 3.1L, 1995 Pontiac Grand Prix SE 3.1L Vin M DTC 77. 1. Remove the throttle body, and inspect the Exhaust Gas Recirculation Valve (EGR) port in the intake plenum. 2. The passage plugs at the bottom where it dumps into the plenum. 3. Best to use an old speedometer cable in a drill to run inside the passage to knock all the carbon out. Restricted Exhaust Gas Recirculation (EGR) Passages When an EGR solenoid is activated by the Powertrain Control Module (PCM), the PCM monitors the change in the Manifold Absolute Pressure (MAP) reading. Carbon deposits anywhere in the EGR passageways will set this code.