1995 G20 CHEVY VAN


You are searching repair manual in PDF format about 1995 G20 CHEVY VAN use another keyword for search another post or files



  1995 G20 CHEVY VAN Direct Download speed 5787 Kb/s

  1995 G20 CHEVY VAN Full Version speed 6767 Kb/s




1995 Chevrolet Chevy Van G20 Exploded View Of 4L60-E Transmission Internal Components

0

Filed Under (Chevrolet) by admin on 02-05-2010

download
OVERHAUL – 4L60-E Fig. 16: Exploded View Of 4L60-E Transmission Internal
Components GENERAL MOTORS CORP.
1995 Chevrolet Chevy Van G20

2005 Chevy Astro Van Wheel Speed Sensor Replacement (RWD) Removal Procedure

0

Filed Under (Chevrolet) by admin on 15-09-2010

download
1. Raise and support the vehicle. Refer to Vehicle Lifting. 2. Remove the tire and wheel. 3. Remove the brake rotor (2). Refer to Brake Rotor Replacement – Front. 4. Important: The wheel speed sensor mounts to the hub/bearing assembly. Thoroughly clean around this area in order to prevent any dirt or contaminants from entering the sealed wheel bearing. Failure to do this may lead to premature wheel bearing failure. Remove the Wheel Speed Sensor (WSS) mounting bolt. 5. NOTICE: Carefully remove the sensor by pulling it straight out of the bore. DO NOT use a screwdriver, or other device to pry the sensor out of the bore. Prying will cause the sensor body to break off in the bore. Remove the wheel speed sensor (5) from the hub/bearing assembly (4). Remove the WSS cable mounting clip from the knuckle. Remove the WSS cable mounting clip from the upper control arm. Remove the WSS cable mounting clip from the frame attachment point. Remove the WSS cable electrical connector. 6. 7. 8. 9. Installation Procedure 1. Plug the WSS bore to prevent debris from falling into the hub. 2. Using a wire brush or equivalent, clean the WSS mounting surface on the hub to remove any rust or corrosion. 3. Apply a thin layer of wheel bearing lubricant, GM P/N 01051344 to the hub surface and the sensor O-ring prior to the sensor installation.

1995 Chevrolet Tahoe 1995 Chevrolet C1500 1993 GMC K2500 engine stumbles on acceleration

0

Filed Under (Chevrolet) by admin on 10-06-2010

download
Customer Concern: The engine stumbles on acceleration and the Exhaust Gas Recirculation (EGR) valve is opening too soon. Tests/Procedures: 1. With the engine off, use a vacuum pump to pump the valve open. It should pump up and hold vacuum. 2. With the valve still pumped up, reach in and crank the engine over, the valve should slam shut and be closed before the engine starts. Potential Causes: Defective Exhaust Gas Recirculation (EGR) Valve Tech Tips: This has a negative back pressure type valve. The back pressure circuit in the valve gets plugged and causes the valve to open too soon. Diagnostic Codes: None

BMW 5-Series (E34) Repair Manual 525i, 530i, 535i, 540i, Touring 1989-1995

0

Filed Under (BMW) by admin on 07-09-2009

BMW 5 Series from 1989 to 1995. The aim throughout this manual has been simplicity, clarity and completeness, with practical explanations, step-by-step procedures and accurate specifications. Whether you’re a professional or a do-it-yourself BMW owner, this manual will help you understand, care for and repair your E34 5 Series.

Models and engines covered:
525i (M20 with DME 1.3) 1989-1990
525i (M50 with DME 3.1) 1991-1992
525i (M50TU/VANOS with DME 3.3.1) 1993-1995
530i (M60 with DME 3.3) 1994-1995
535i (M30 with DME 1.3) 1989-1993
540i (M60 with DME 3.3) 1994-1995
Transmissions covered:
Manual (remove, install, external service)
Getrag 260/5 and 260/6
Getrag S5D 250G
Getrag S6S 560G
Automatic (remove, install, external service)
ZF 4HP22/EH
A4S 310R (THM-R1)
ZF A5S 310Z
ZF A5S 560Z

MAINTENANCE INFORMATION 1995 Volvo 850

0

Filed Under (Volvo) by admin on 20-04-2010

download
1993-96 MAINTENANCE Volvo Maintenance Information 1993-96 850 Sedan 1994-96 850 Turbo Sedan 1995-96 850 T-5R Turbo Sedan
1994-96 850 Wagon 1994-96 850 Sportswagon 1995-96 850 T-5R Turbo Sportswagon cover CAMSHAFT TIMING BELT CAMSHAFT TIMING BELT REPLACEMENT INTERVAL ALIGNING CAMSHAFT TIMING MARKS Fig. 5: Lubricating Tensioner Pulley Bushing (Pivot Bearing) Courtesy of Volvo Cars of North America. CAUTION: Lubrication of the Tensioner Pulley Bushing is REQUIRED on 1993 Models, it is recommended that the bushing be checked for free play and lubrication on 1994-95 models. NOTE: For more information regarding camshaft timing belt service refer to the 2.3L 5-CYL TURBO article in the ENGINE MECHANICAL section. Fig. 6: Installing Washer on Timing Belt Tensioner