1995 cadillac sls
You are searching repair manual in PDF format about 1995 cadillac sls use another keyword for search another post or files
Filed Under (Cadillac) by admin on 28-09-2010
REMOVAL Wheels must be in a straight forward position and the key must be in the Lock position when removing or installing column to ensure proper alignment of components during installation. 1. Remove inflator module as outlined in Air Bag. Refer to Air Bags and Seat Belts/Air Bags(SRS). 2. Remove knee bolster and steering column reinforcement plate. 3. Disconnect electrical connectors from column. 4. Remove pinch bolt from intermediate shaft, Fig. 13. 5. Remove lower support bracket from vehicle. 6. Remove upper column support from instrument panel, then the column from vehicle. INSTALLATION 1. Install column in vehicle and support at upper bracket with two bolts, Fig. 14, do not tighten at this time. 2. Install column lower support bracket in vehicle, do not tighten at this time. 3. Connect column intermediate shaft to steering rack, install pinch bolt and torque to 35 ft. lbs. 1994 Cadillac Seville SLS V8-4.6L VIN Y 4. 5. 6. 7. Torque upper and lower column support bolts to 20 ft. lbs., then the lower bracket to column screws to 12 ft. lbs. Connect electrical connectors to column. Install knee bolster and column reinforcement plate. Install steering wheel inflator module as outlined in Air Bag. Refer to Air Bags and Seat Belts/Air Bags(SRS).
Filed Under (Cadillac) by admin on 07-08-2010
Models: 1992-94 Buick Skylark 1993-96 Buick Park Avenue 1989-92 Cadillac Allante 1991-93 Cadillac Eldorado, Seville 1991-95 Cadillac DeVille 1991-95 Oldsmobile Ninety Eight 1992-93 Oldsmobile Achieva 1994-99 Pontiac Bonneville This bulletin is being revised to clarify when this bulletin may be used to turn the service suspension lamp off. Also, a step has been added to the 1991 Cadillac Eldorado and Seville repair. Please discard Corporate Bulletin Number 00-03-11-001 (Section 3 – Suspension). Some owners may bring their vehicles in for service with an illuminated service suspension light. The service suspension indicator lamp is telling the owner that the vehicle is due for strut/shock replacement, a maintenance item. The customer may elect to have passive struts installed in their vehicles due to repair cost savings and/or parts availability. The installation of passive shock/struts will result in handling characteristics which are the equal to a like vehicle without the computer controlled ride, with all other components such as tires, tire pressure, springs, etc. being equal. The installation of (4) new passive struts will cause the continued illumination of the service suspension indicator. If desired by the customer, the service indicator may be disabled AFTER THE INSTALLATION OF THE (4) NEW PASSIVE STRUTS, using the appropriate service procedure listed below. This bulletin DOES NOT authorize this procedure unless (4) NEW PASSIVE STRUTS WERE INSTALLED ON THE VEHICLE.
Filed Under (Cadillac) by admin on 24-06-2010
Service Engine Soon (SES) Light On, Diagnostic Trouble Code (DTC) P0741, Torque Converter Clutch (TCC) Excessive Slip, Transaxle Chuggle, Slip/Surge (Inspect and/or Replace Various Internal Transaxle Components) 1998-2002 Cadillac Eldorado 1998-2004 Cadillac Seville 1999-2004 Cadillac DeVille 2000-2003 Oldsmobile Aurora with 4T80-E Auto Transaxle (RPO MH1) Some customer may comment on the SES light on and a chuggle or surge. Diagnostics may show excessive TCC slip speed and DTC P0741 will be current code Seal damage may allow the TCC apply fluid to leak into the channel plate, causing excessive TCC slippage under certain conditions, eventually causing no TCC apply.
Filed Under (Chevrolet) by admin on 10-06-2010
Customer Concern: The engine stumbles on acceleration and the Exhaust Gas Recirculation (EGR) valve is opening too soon. Tests/Procedures: 1. With the engine off, use a vacuum pump to pump the valve open. It should pump up and hold vacuum. 2. With the valve still pumped up, reach in and crank the engine over, the valve should slam shut and be closed before the engine starts. Potential Causes: Defective Exhaust Gas Recirculation (EGR) Valve Tech Tips: This has a negative back pressure type valve. The back pressure circuit in the valve gets plugged and causes the valve to open too soon. Diagnostic Codes: None
Filed Under (BMW) by admin on 07-09-2009
BMW 5 Series from 1989 to 1995. The aim throughout this manual has been simplicity, clarity and completeness, with practical explanations, step-by-step procedures and accurate specifications. Whether you’re a professional or a do-it-yourself BMW owner, this manual will help you understand, care for and repair your E34 5 Series.
Models and engines covered:
525i (M20 with DME 1.3) 1989-1990
525i (M50 with DME 3.1) 1991-1992
525i (M50TU/VANOS with DME 3.3.1) 1993-1995
530i (M60 with DME 3.3) 1994-1995
535i (M30 with DME 1.3) 1989-1993
540i (M60 with DME 3.3) 1994-1995
Manual (remove, install, external service)
Getrag 260/5 and 260/6
Getrag S5D 250G
Getrag S6S 560G
Automatic (remove, install, external service)
A4S 310R (THM-R1)
ZF A5S 310Z
ZF A5S 560Z