1995 range rover automatic transmission manual fre


You are searching repair manual in PDF format about 1995 range rover automatic transmission manual fre use another keyword for search another post or files



  1995 range rover automatic transmission manual fre Direct Download speed 5787 Kb/s

  1995 range rover automatic transmission manual fre Full Version speed 6767 Kb/s




2003-2005 Chevrolet TrailBlazer Automatic Transmission/Torque Converter Clutch (TCC) Shudder

0

Filed Under (Chevrolet) by admin on 30-12-2010

download
Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. Correction First, repair the transmission and second, replace the transmission fill tube, seal and level indicator to prevent repeat water contamination of the ATF. Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: If water or coolant is found in the transmission, the following components MUST be replaced. • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow . Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube.

Related entry:

2000 ford focus transmission removal, turbo 400 transmission diagram, miata 6 speed transmission shop manual, 4t65e transmission exploded view, miata 6 speed manual transmission diagram, 2004 chevy venture transmission diagram, 6r60 transmission diagra, 1985 Chevy Silverado Transmission, 4HP-22 automatic repair atsg for dowload free, T400 Transmission,

2006 Land Rover Range Rover Sport Parking Brake Actuator Removal

0

Filed Under (Rover) by admin on 24-10-2010

download
1. Using the Land Rover approved diagnostic system, drive the parking brake to the ‘mounting position’. 2. Isolate the parking brake electrical circuit. Remove fuse number 8 from the BJB. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. 3. Raise and support the vehicle. 4. Remove the rear wheels and tires. 5. Release the parking brake shoe adjustment. Remove the plug from the access hole in the brake disc. Using a suitable tool, rotate the brake shoe adjuster to release the adjustment. CAUTION: Do not allow the brake caliper to hang on the brake hose. 6. Reposition the RH rear brake caliper. Remove the 2 bolts. Using a suitable tie strap, support the brake caliper. 7. Remove the RH rear brake disc. Remove the screw. CAUTION: Do not allow the brake caliper to hang on the brake hose. 8. Reposition the LH rear brake caliper. Remove the 2 bolts. Using a suitable tie strap, support the brake caliper. 9. Remove the LH rear brake disc. Remove the screw. 10. Disconnect both parking brake cables from the wheel hubs. Fully loosen the nut. Release the cable from the lower arm. Disconnect the inner cable from the brake shoe 11. Release the LH parking brake cable. Remove the 2 bolts. Release the 3 wiring harness clips. Release the cable from the clip on the chassis.

Related entry:

2003 FREELANDER FIRING ORDER, torque Specs for bolts on a head 1999 Range Rover, 04 rover p1170, land rover freestyle 2004 firing order, landrover discovery sd engine removal,

2006 Land Rover Range Rover Sport Parking Brake Shoes Removal

0

Filed Under (land rover) by admin on 18-10-2010

download
NOTE: If the parking brake shoes or the brake discs have been removed for access to other components then DO NOT carry out the bedding in procedure. 1. Using the Land Rover approved diagnostic system, drive the parking brake to the mounting position. 2. Isolate the parking brake electrical circuit. Remove fuse number 8 from the BJB. 3. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle. 4. Remove the wheels and tires. 5. Release the brake caliper. Remove the brake caliper anchor bolts. 6. CAUTION: Do not allow the brake caliper to hang on the brake hose. Tie the brake caliper aside. 7. Release the park brake shoe adjustment. Remove the plug from the access hole in the brake disc. Using a suitable tool, rotate the brake shoe adjuster to release the adjustment. 8. Remove the brake disc. Remove the Torx screw. 10. Remove the primary brake shoe. Remove the hold-down spring and retaining pin. Pivot the shoe to release it from the spreader plate and return spring. 11. Remove the spreader plate and spring. 12. Remove the return spring. Remove the hold-down spring and retaining pin. Disconnect the parking brake cable retaining spring from the brake shoe lever. Release the parking brake cable.

Related entry:

firing sequence for Land Rover Range Rover 2004, removing ing key cyl from 04 land rover discovery,

2006 Ford Crown Victoria Automatic Transaxle/ Transmission REMOVAL

0

Filed Under (Ford) by admin on 19-02-2011

download
NOTICE: Whenever a transmission has been disassembled to install new parts, the transmission fluid cooler tubes must be cleaned and backflushed using a suitable torque converter/fluid cooler cleaner. A new Oil-To-Air (OTA) transmission fluid cooler must also be installed. When internal wear or damage has occurred in the transmission, metal particles, clutch plate material or band material may have been carried into the torque converter and fluid cooler. These contaminants are a major cause of recurring transmission concerns and must be removed from the system before the transmission is put back into service. NOTE: After the transmission is removed for a major overhaul, it is important to completely clean all transmission components, including torque converter, cooler inlet tube, main control valve body, clutches and all coasting booster valve shuttle balls after any transmission service that generates contamination. These contaminants are a major cause for recurring transmission concerns and must be removed from the system before the transmission is returned to service. The cleaning of foreign material from the direct clutch check ball is often omitted. This omission can lead to a repeat servicing of the transmission. A new Oil-To-Air (OTA) transmission fluid cooler must be installed under the following condition. For additional information, refer to Section 307-02. Evidence of broken transmission components or transmission fluid contamination found due to the following transmission or converter failure modes: Major metallic failure Multiple clutches or clutch plate failure Sufficient component wear which results in metallic contamination 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01. 2. WARNING: Before servicing a vehicle equipped with a fire suppression system, depower the system by following the procedure in Section 419-03. Failure to follow the instructions may result in serious personal injury. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02. 3. NOTE: Only if transmission disassembly or replacement is required, drain the transmission fluid. For additional information, refer to Fluid Pan, Gasket and Filter in this section. Drain the transmission fluid. Loosen the transmission fluid pan bolts and allow the transmission fluid to drain. After transmission fluid has drained remove the bolts and the pan and drain the remaining transmission fluid that is in the pan. 4. Install the transmission fluid pan and the old transmission fluid pan gasket. 1. Position the transmission fluid pan gasket. 2. Position the transmission fluid pan. 5. NOTE: To maintain the initial driveshaft balance, mark the rear driveshaft yoke and the axle pinion flange so they can be installed in their original positions. Mark the rear driveshaft yoke and the axle pinion flange and remove the 4 bolts.

Related entry:

How to Remove Transmission 02 town and country, 2001 Ford Windstar Transmission Removal, 1997 merury mountaineer yransmission removsl, how to remove the tranaxle on a 2002 chev venture, 1940 Ford Transmission Removal Instructions, nissan altima 2003 transmission pan removal, howbto wire older 4L60 to replace 4L60e, 2004 ford escape transaxle removal, PT Cruiser Transmission Removal, remove manual transmission 03 cavalier,

2006 Ford Explorer Transmission Fluid Refill procedure

0

Filed Under (Ford) by admin on 07-03-2011

download
Transmission Fluid Refill NOTICE: This procedure contains the air purge steps required to purge air from the cooling system. This procedure is NOT intended for use with the Transmission Fluid Level Check. NOTICE: The vehicle should not be driven if the fluid level is low as internal failure could result. NOTICE: The fluid fill plug is located near the exhaust system. The exhaust will be extremely hot during this procedure. NOTICE: The use of any other transmission fluid than specified, can result in the transmission failing to operate in a normal manner or transmission failure. NOTE: If the transmission starts to slip, shifts slowly or shows signs of fluid leaking, the fluid level should be checked. NOTE: Here is an overview of the Transmission Fluid Drain and Refill procedure. Adding 3.3L (3.5 qt) of clean automatic transmission fluid to the transmission is an initial fill enabling you to start the engine. The cold level range shown in the procedure allows the vehicle to be driven. The vehicle should be driven to allow the transmission fluid temperature to reach 85ºC-88ºC (185ºF-190ºF) in order to purge the air from the transmission cooling system. Fill the transmission fluid to the fill range on the fluid level indicator at the normal operating range 80ºC-85ºC (175ºF-185ºF). 1. NOTE: The transmission will need 3.3L (3.5 qt) of clean automatic transmission fluid added to the transmission as an initial fill if: the transmission has been overhauled. a new mechatronic assembly has been installed. the transmission fluid pan or fluid filter have been removed. Using the special tool, add 3.3L (3.5 qt) of clean automatic transmission fluid to the transmission through the fluid fill hole. For additional information, refer to Adding Additional Transmission Fluid in this procedure. 2. Check the transmission fluid level cold. 1. The vehicle is safe to drive if the transmission fluid is in the cold level range 32°C-43°C (90° F-11 0° F). Using the scan tool and the engine running, place the transmission selector lever in each gear position and hold approximately 5 seconds. Place the transmission selector lever in PARK, with the engine at idle (600-750 rpm).

Related entry:

draining transmission fluid in a 2008 torrent, autorepair oil change suzuki 2005, Chevy HHR Transmission Fluid Change for2006, 2007 pontiac torrent transmission fluid, how do you drain the transmission fluid in a 2008 torrent, 2006 Hydai sonata transmission circuit high, 2006 ford explorer transmission fluid lines, how to fill transmission fluid 2008 explorer, 2006 chevy equinox transmission drain an fill procedure, 2002 ford escape transmission fluid capacity,