1997 bmw 328i o2 sensor test


You are searching repair manual in PDF format about 1997 bmw 328i o2 sensor test use another keyword for search another post or files



  1997 bmw 328i o2 sensor test Direct Download speed 5787 Kb/s

  1997 bmw 328i o2 sensor test Full Version speed 6767 Kb/s




1995 Ford Mustang Camshaft Position (CMP) Sensor Removal Installation

0

Filed Under (Ford) by admin on 08-02-2011

download
1. Disconnect battery ground cable (14301) . 2. Disconnect fuel charging wiring (9D930) from distributor stator (12A112) (camshaft position sensor). 3. Remove stator camshaft position sensor retaining screws and distributor stator (camshaft position sensor) from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the engine front cover (6019) , proceed with Removal Step 5. If camshaft position sensor housing is not being removed, proceed to Installation Step 6. 5. CAUTION: Before proceeding with this procedure, set cylinder No. 1 to 26 degrees After Top Dead Center (ATDC) of the compression stroke. Then note the position of the stator (camshaft position sensor) electrical connector. The installation procedure requires that the connector be located in the same position. Remove retaining bolt and hold-down clamp (12270) . 6. NOTE: The oil pump intermediate shaft (6A618) should be removed with the camshaft position sensor housing. Remove camshaft position sensor housing from engine front cover . Installation 1. CAUTION: If the replacement distributor stator (camshaft position sensor) does not contain a plastic locator cover tool, a special service tool such as Syncro Positioning Tool T89P-12200-A must be obtained prior to installation of the replacement distributor stator (camshaft position sensor). Failure to follow this procedure will result in improper stator (camshaft position sensor) alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. If the plastic locator cover tool is not attached to the replacement distributor stator (camshaft position sensor), attach Syncro Positioning Tool T89P-12200-A as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. The cover tool should be square and in contact with entire top surface of camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 30 degrees counterclockwise from the front face of the cylinder block (6010) . This step will locate stator (camshaft position sensor) electrical connector in the pre-removal position. 4. Install hold-down clamp and retaining bolt and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove Syncro Positioning Tool T89P-12200-A. 6. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install distributor stator (camshaft position sensor) and retaining screws. Tighten screws to 2.5-3.5 Nm (22-31 lb-in). 7. Connect fuel charging wiring connector to distributor stator (camshaft position sensor). 8. Connect battery ground cable .

Related entry:

removing map sensor b2500, how do I remove a camshaft position sensor on a 2011 Chevrolet Impala, Mazda 3 throttle angle setting, 2002 cavalier tps replacement, 95 4runner compressor temperatureswitch, 2008 gmc denali camshaft sensor, how to change map sensor on a 2006 hhr, ac evaporater sensor lincoln zephyr, 2006 mercury milan evaporator temp sensor location, CHT Sensor 5 4L,

1998 Ford Windstar Camshaft Position (CMP) Sensor REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 17-02-2011

download
CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126) , set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires the connector be located in the same position. Removal 1. Disconnect battery ground cable (14301). Refer to Section 14-01. 2. Disconnect fuel charging wiring connector from camshaft position sensor. 3. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to Step 6 of the installation procedures. 5. Remove hold-down clamp (12270) (bolt and washer assembly). 6. NOTE: Remove the oil pump intermediate shaft (6A618) with the camshaft position sensor housing. Remove camshaft position sensor housing from cylinder block. Installation 1. CAUTION: If the replacement camshaft position sensor housing does not contain a plastic locator cover tool, a special service tool must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the ignition fuel system being out of time with the engine, possibly causing engine damage. NOTE: For 3.0L engines, use Syncro Positioning Tool 303-589. For 3.8L engines, use Syncro Positioning Tool 303-562 (T96T-12200-A). If the plastic locator cover tool is not attached to the replacement camshaft position sensor housing, attach syncro positioning tool as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. Install camshaft position sensor housing so drive gear engagement occurs when arrow on syncro positioning tool is pointed approximately as shown in the illustrations. This step will locate camshaft position sensor electrical connector in the pre-removal position. 4. Install hold-down clamp (washer and bolt assembly) and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove syncro positioning tool. 6. CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor and retaining screws. On 3.0L engine, tighten screws to 2.5-3.5 Nm (23-30 lb-in). On 3.8L engine, tighten screws to 4.5-7 Nm (40-61 lb-in). 7. Connect fuel charging wiring connector to camshaft position sensor. 8. Connect battery ground cable. Refer to Section 14-01. Camshaft Position Sensor—3.0L Engine

Related entry:

how to adjust transmission range sensor on saturn, how to check maf sensor on a 2008 toyota camry 4 cylinder, J 41364 A Tool, where is located the knock sensor in chevy suburban 1998,

2003-2006 Chevrolet Express Antilock Brake (ABS) Activation At Low Speeds (Clean Wheel Speed Sensor Mounting Surface)

0

Filed Under (Chevrolet) by admin on 25-01-2011

download
Condition Some customers may comment on ABS activation at low speeds, usually below 8 km/h (5 mph). Upon investigation, the technician will find no DTCs set. Cause The cause of this condition may be an increased air gap between the wheel speed sensor and the hub reluctor ring due to rust and debris built up on the sensor mounting surface. Correction Measure AC voltage and clean the wheel speed sensor mounting surfaces. 1. 2. 3. 4. Raise and support the vehicle. Disconnect both the front wheel speed sensor connectors at the frame and harness. Place a Digital Volt Meter (DVM) across the terminals of each wheel speed sensor connector. Rotate the wheel clockwise approximately one revolution per second. The minimum reading should be at least 350 ACmV’s. If the reading is less than 350 ACmV’s, remove the wheel speed sensor. 5. Plug the wheel speed sensor bore in order to prevent debris from falling into the hub during service. 6. Clean the wheel speed sensor mounting surface using a wire brush, sand paper, emery cloth, scotch brite, or other suitable material. Be sure to thoroughly clean the wheel speed sensor surface. There should be no rust or corrosion. 7. Check the sensor head to determine if it has been warped/distorted due to the corrosion build up or other causes. Check the mounting surface on the sensor head for flatness by placing it on the edge of a metal machinists scale or other suitable straight edge to measure the flatness. Check the sensor for flatness in multiple (minimum 3) positions/directions. If the sensor head is distorted, replace the sensor. 8. Apply (spray) two thin coats of the specified rust penetrating lubricant (corrosion inhibitor) to the complete sensor mounting surface on the bearing hub. Allow to dry for 3-5 minutes between coats. Use ONLY Rust Penetrating Lubricant, P/N 89022217 (in Canada, P/N 89022218). 9. When the corrosion inhibitor is dry to the touch (about 10 minutes), apply a thin layer of bearing grease to the hub surface and sensor O-ring prior to sensor installation. Use ONLY Wheel Bearing Lubricant, P/N 01051344 (in Canada, P/N 993037). 10.Install either the original sensor or a new one in the hub. Ensure that the sensor is seated flush against the hub. Refer to the applicable Wheel Speed Sensor Replacement procedure in the ABS sub-section of the Service Manual. 11.Place the DVM across the sensor terminals and recheck the voltage while rotating the wheel. The voltage should now read at least 350 ACmV’s.

Related entry:

how to install turbine sensor in mazda 6, 2006 kia spectra ex speed sensors diagram, how to clean map sensor on 08 hhr, how to 2003 gmc sonoma abs module repair, engine speedsensor hiace, disconnecting front abs sensor 2004 ford escape, 2011 chrysler 300 C front wheel speed sensor, 2009 hyundai input/turbine speed sensor, 2006 ford escape abs ring gear replacement, 1999 chevy caviler speed senser,

2002 Jeep Wrangler CMP and CKP Removal and Installation

0

Filed Under (Jeep) by admin on 01-12-2010

download
The Camshaft Position Sensor (CMP) on the 4.0L 6cylinder engine is bolted to the top of the oil pump drive shaft assembly. The sensor and drive shaft assembly is located on the right side of the engine near the oil filter. The rotational position of oil pump drive determines fuel synchronization only. It does not determine ignition timing. WARNING Do NOT attempt to rotate the oil pump drive to modify ignition timing. 1. Two different procedures are used for Removal & Installation. The first procedure will detail Removal & Installation of the sensor only. The second procedure will detail Removal & Installation of the sensor and oil pump drive shaft assembly. The second procedure is to be used if the engine has been disassembled. 2. An internal oil seal is used in the drive shaft housing that prevents engine oil at the bottom of the sensor. The seal is not serviceable. Sensor Only 1. Disconnect electrical connector at CMP sensor. 2. Remove 2 sensor mounting bolts. 3. Remove sensor from oil pump drive. Oil Pump Drive & Sensor WARNING If the CMP and oil pump drive are to be removed and installed, do NOT allow engine crankshaft or camshaft to rotate. CMP sensor relationship will be lost. Disconnect electrical connector at CMP sensor. Remove 2 sensor mounting bolts Remove sensor from oil pump drive. Before proceeding to next step, mark and note rotational position of oil pump drive in relationship to engine block. After installation:, the CMP sensor should face rear of engine 0. 5. Remove hold-down bolt and clamp. 6. While pulling assembly from engine, note direction and position of pulse ring. After Removal & Installation, look down into top of oil pump and note direction and position of slot at top of oil pump gear. 7. Remove and discard old oil pump drive-to-engine block gasket. 1. 2. 3. 4. Sensor Only The Camshaft Position Sensor (CMP) on the 4.0L 6cylinder engine is bolted to the top of the oil pump drive shaft assembly. The sensor and drive shaft assembly is located on the right side of the engine near the oil filter. 1. Install sensor to oil pump drive. 2. Install 2 sensor mounting bolts and tighten to 2 Nm (15 inch lbs.) torque. 3. Connect electrical connector to CMP sensor. Oil Pump Drive & Sensor 1. Clean oil pump drive mounting hole area of engine block. 2. Install new oil pump drive-to-engine block gasket.

Related entry:

ford 4 0 sohc oil pump driveshaft, HOW TO REPLACE CV JOINTS ON MERCEDES VITO 2003, diagram oil sender switch skoda fabia 01 plate, what the torque rench settings for the drive shaft nut on a mercedes vito 108 cdi, where is the crankshaft sensor on a 2002 dodge grand caravan 3 3l,

1999 Ford Expedition Climate Control System DIAGNOSIS AND TESTING

0

Filed Under (Ford) by admin on 28-03-2011

download
Inspection and Verification 1. Verify the customer’s concern by operating the climate control system to duplicate the condition. 2. Inspect to determine if one of the following mechanical or electrical concerns apply: Visual Inspection Chart Loose, missing or damaged A/C compressor drive belt. Loose or disconnected A/C clutch. Loose, misrouted or damaged vacuum lines. Broken or leaking vacuum control motora Discharged A/C system. Broken or leaking refrigerant lines. a a A leak in the vacuum control circuit may occur during acceleration (slow leak), may exist at all times (large leak), and may exist only when specific functions are selected (indicating a leak in that portion of the circuit). The vacuum hoses used in the passenger compartment control circuit are constructed from PVC plastic material. The vacuum hoses used in the engine compartment are constructed of Hytrel®. Because of the materials used, never pinch the vacuum hoses off during diagnosis to locate a leak. A wood golf tee can be used as a plug when it is necessary to plug one end of the vacuum hose for leak test purposes. 3. If the inspection reveals obvious concern(s) that can be readily identified, service as required. 4. If equipped with the electronic automatic temperature control system, go to Step 6. 5. If equipped with a manual A/C system, determine the symptom and go to the Symptom Chart. 6. If the concern remains after the inspection, connect the Rotunda New Generation Star (NGS) Tester to the data link connector (DLC) located beneath the instrument panel to carry out the DATA LINK DIAGNOSTICS test. If the NGS responds with NO RESPONSE/NOT EQUIPPED for the electronic automatic temperature control module, GO to Pinpoint Test A. If the DATA LINK DIAGNOSTICS test is passed for the electronic automatic temperature control module, retrieve the continuous DTCs and execute the Self-Test Diagnostics for the electronic automatic temperature control module to retrieve the current DTCs. Mechanical Electrical Open fuses. Blower motor inoperative. A/C compressor inoperative. Circuitry open/shorted. Disconnected electrical connectors. 7. If the self-test is passed and no DTCs are retrieved, go to the Symptom Chart to continue diagnostics. 8. If DTCs are retrieved, go to the Electronic Automatic Temperature Control (EATC) Module Diagnostic Trouble Code (DTC) Index to continue diagnostics. 9. If the electronic automatic temperature control module cannot be accessed by the NGS, GO to Pinpoint Test A. Electronic Automatic Temperature Control Module Self-Test The EATC module self-test will not detect concerns associated with data link messages like engine coolant temperature or vehicle speed signals. A NGS tester must be used to retrieve these concerns. The EATC module self-test will detect concerns in the system control functions and will display hard diagnostic trouble codes (DTCs) in addition to intermittent diagnostic trouble codes for concerns that occur during system operation. The vehicle interior temperature should be between 4-32° (40-90°F) when performing the self-test. If the temperatures are C not within the specified ranges, false in-car temperature sensor DTCs will be displayed. The self-test can be initiated at any time. Normal operation of the system stops when the self-test is activated. To enter the self-test, press the OFF and FLOOR buttons simultaneously and then press the AUTOMATIC button within two seconds. The display will show a pulse tracer going around the center of the display window. The test may run as long as 30 seconds. Record all DTCs displayed. If any DTCs appear during the self-test, follow the diagnostics procedure given under ACTION for each DTC given. If a condition exists but no DTCs appear during the self-test, refer to the Symptom Chart Condition: The EATC System Is Inoperative, Intermittent or Improper Operation. To exit self-test and retain all intermittent DTCs, push the blue (cooler temperature) button. The control will exit self-test, retain all intermittent DTCs and then turn OFF (display blank). To exit self-test and clear all DTCs, press the DEFROST button. The vacuum fluorescent display window will show 888 and all function symbols for one second. Then, the EATC control assembly will turn OFF (display blank) and all DTCs will be cleared. Always exit the self-test before powering the system down (system turned OFF). Intermittent DTCs will be deleted after 80 ignition switch ON cycles after the intermittent condition occurs.

Related entry:

no powertrain dtcs or freeze frame data, n powertrain dtc, ac test 04 acura tl, 2004 honda pilot climate control diagnostic codes, 2000 Mustang Traction Control Repair, 1995 ford f 150 climate control wiring diagram for free, www tomanual com/search/2003 ford f150 supercrew vacuum diagram for climate control, 2001 buick lesabre elc level sensor location, 1999 f150 vacuum lines to climate controls, 2002 explorer soleniod diagnostic,