1997 bravada oil pan removal


You are searching repair manual in PDF format about 1997 bravada oil pan removal use another keyword for search another post or files



  1997 bravada oil pan removal Direct Download speed 5787 Kb/s

  1997 bravada oil pan removal Full Version speed 6767 Kb/s




2003 Buick Century Engine Oil and Oil Filter Replacement Removal Procedure

0

Filed Under (Buick) by admin on 15-12-2010

download
1. 2. 3. 4. 5. Raise and support the vehicle. Refer to Vehicle Lifting. Position the oil drain pan under the engine oil drain plug. Remove the engine oil drain plug. Clean and inspect the engine oil drain plug, repair or replace if necessary. Clean and inspect the engine oil drain plug sealing surface on the oil pan, repair or replace oil pan if necessary. 6. Remove the oil filter. 7. Clean and inspect the oil filter sealing area on the engine block, repair or replace if necessary. Installation Procedure 1. Lightly oil the replacement oil filter gasket with clean oil and install the new oil filter. Notice: Refer to Fastener Notice in Service Precautions. 2. Install the new oil filter. Tighten the new oil filter to 3/4 to 1 full turn, after the oil filter gasket contacts the oil filter mounting surface. 3. Install the engine oil drain plug. Tighten the plug to 30 Nm (22 ft. lbs.) . 4. 5. 6. 7. 8. 9. Remove the oil drain pan. Lower the vehicle. Fill the engine with new engine oil. Start the engine. Inspect for oil leaks after engine start up. Turn off the engine and allow the oil a few minutes to drain back into the oil pan. Remove the oil level indicator from the oil level indicator tube. Clean off the indicator end of the oil level indicator with a clean paper towel or cloth. Install the oil level indicator into the oil level indicator tube until the oil level indicator handle contacts the top of the oil level indicator tube. Again, remove the oil level indicator from the oil level indicator tube keeping the tip of the oil level indicator down. Check the level of the engine oil on the oil level indicator. If necessary, adjust the oil level by adding or draining the engine oil. 10. 11. 12. 13. 14. 15.

Related entry:

where is oil filter located on honda muv700, Sanden AC Compressor Oil Capacity, ac compressor oil capacity chart, 1999 where is cadillac catera oil level sensor, a/c compressor oil capacity chart, transit duratorg 2 4 oil change, were is a 2008 uplander oil pressure switch located, porsche 996 oil filter torque specs, change oil pump 2002 expedition, how to change a 2001 ford escape oil pan,

1999 Audi A4 Quattro Sedan Oil Pan (Upper Part) and Oil Pan (Lower Part), Removing and Installing

0

Filed Under (Audi) by admin on 23-10-2010

download
Special tools and equipment z z z z Drill with plastic brush attachment Silicon sealant D 176 404 A2 Torque wrench 10 Nm/45 Nm Switch ignition off and disconnect battery Ground (GND) strap. CAUTION: Before disconnecting the battery, determine the correct coding for the anti-theft radio. z Withdraw dipstick. z Unbolt dipstick tube on cylinder head, pull up and remove. z z z z Remove noise insulation panel (arrows). Lock carrier in service position. Refer to Engine, disassembling and assembling. Drain engine coolant. Drain engine oil into appropriate receptacle. Vehicles with automatic transmission z Unbolt oil line bracket from right-side of oil pan. z Set 10-222A engine support bridge together with 10-222A/3 engine support adapter on fender mounting edges. z Attach 2024A engine sling to mounting eyes at front and rear of engine. z Using 10-222A engine support bridge spindle, lift up engine as far as possible. z z z z z Cut tie wraps (arrows), open bracket for starter wiring and remove wiring. Remove torque support at front of engine. Unbolt coolant line at front of engine from oil pan. Disconnect harness connector from oil pressure switch on left-side of oil pan. Disconnect coolant lines from oil cooler underneath oil filter. z Remove left and right nuts from lower engine mount -1-. z Mark installation positions for threaded assembly -1- and guide sleeves -2- on left and right lower engine mounts. z First remove front bolts -2- and -3- from left and right sides of subframe. Then remove bolts -4-. z Swing stabilizer down. z Remove starter. Note: Only loosen or lower subframe at front to avoid changing wheel alignment.

2004 Ford F-150 Oil Pan, Oil Pump, Oil Pump Screen and Pickup Tube IN-VEHICLE REPAIR

0

Filed Under (Ford) by admin on 20-02-2011

download
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-00. 2. If oil pump removal is necessary, remove the timing drive components. For additional information, refer to Timing Drive Components in this section. 3. Drain the engine oil. 4. If equipped, remove the skid plate. 5. Remove the bolts in sequence shown and remove the crossmember. 6. Remove the parts in the order indicated in the following illustrations and tables. To remove individual parts, only carry out the listed steps: 7. To install, reverse the removal procedure. Item 1: Front Drive Axle Assembly Removal Note 1. Position a suitable hydraulic jack under the front axle. Securely strap the jack to the axle. 2. NOTE: Rotate the steering column so the pinch bolt for the steering column coupling allows clearance for the isolator bolt. Remove the upper front axle carrier mounting bushing bolt. 3. Remove the axle shaft housing carrier bushing bolt. 4. Remove the lower front axle carrier mounting bushing bolt. 5. Partially lower the front axle assembly. Item 4: Oil Pan Removal Note 1. NOTICE: Do not use metal scrapers, wire brushes, power abrasive discs, or other abrasive means to clean the sealing surfaces. These may cause scratches and gouges resulting in leak paths. Use a plastic scraper to clean the sealing surfaces. Remove and discard the oil pan gasket. Clean the sealing surfaces with silicone gasket remover and m etal surface prep. Follow the directions on the packaging. Inspect the mating surfaces. Items 6-10: Oil Pump, Oil Pump Screen and Pickup Tube and Bolts Removal Note 1. Remove the three bolts, the oil pump screen and pickup tube and the spacer.

2003 Saturn ION Engine Oil and Oil Filter Replacement Removal Procedure

0

Filed Under (Saturn) by admin on 18-08-2010

download
1. Raise and support the vehicle. 2. Place a drain pan under the oil drain plug. 3. Remove the oil pan drain plug. Important: DO NOT use an open end wrench on the hex on top of the oil filter cap. 4. Use a 32 mm (1 1/4 inch) socket on the hex on the top of the oil filter cap, or an oil filter wrench on the outside diameter of the oil filter cap. 5. Remove the oil filter cap with filter. 6. Remove the filter from the cap. Installation Procedure 1. Install the filter to the cap. 2. Install the oil filter cap with filter. Notice: Over torquing the oil filter cap may cause damage to the oil filter cap resulting in an oil leak. Notice: Refer to Fastener Notice in Service Precautions. Important: DO NOT use an open end wrench on the hex on top of the oil filter cap. 3. Use a 32 mm (1 1/4 inch) socket on the hex on the top of the oil filter cap, or an oil filter wrench on the outside diameter of the oil filter cap. – Tighten the oil filter cap until fully seated, DO NOT exceed 25 Nm (18 ft. lbs.). 4. Install the oil pan drain plug. – Tighten the oil pan drain plug to 25 Nm (18 ft. lbs.). 5. Lower the vehicle. 6. Fill the engine with oil

Related entry:

2001 Montero sport cabin filter location, charcoal filter replacement chevrolet silverado, how to take clip off 2003 jetta,

Oil Filter Cap Assembly Precautions

0

Filed Under (Toyota) by admin on 20-05-2011

download
To prevent damage to the oil ?lter cap assembly, this procedure must be closely followed during oil ?lter replacement to avoid immediate and future oil ?lter serviceability concerns. The following engines are equipped with a plastic oil ?lter cap assembly: • 1UR-FE (Tundra, Sequoia) • 3UR-FE (Tundra, Sequoia, Land Cruiser) • 2ZR-FE (Corolla, Matrix) • 1AR-FE (Highlander, Venza) • 2AR-FE (RAV4, Camry) Repair Procedure NOTICE During oil ?lter replacement: • Ensure that SST 09228-06500-02 or 09228-06501 is used to remove and install the oil ?lter cap — or damage to the cap may occur. • Inspect the SST for any damage or distortion before use. • Con?rm that the SST is fully seated on the oil ?lter cap when removing/installing (see Figure 1). Figure 1. 1 3 4 1 2 3 4 • Ensure a torque wrench is used for oil ?lter cap installation. Torque: 25 +/- 5 N*m (255 +/- 51 kgf*cm, 18 +/- 3.7 ft*lbf) • There is a possibility the oil ?lter cap will be dif?cult to remove if the torque range is exceeded. FAILURE TO FOLLOW THE INSTRUCTIONS ABOVE MAY RESULT IN OIL FILTER CAP AND/OR SST DAMAGE. With Drain Plug Without Drain Plug Oil Filter Cap SST (09228-06500-02 or 09228-06501) Refer to the Technical Information System (TIS) when replacing the oil ?lter, applicable model and model year Repair Manual: • 2010 Camry: Engine/Hybrid System – Lubrication – “2AR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 / 2010 Corolla: Engine/Hybrid System – Lubrication – “2ZR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 Highlander: Engine/Hybrid System – Lubrication – “1AR-FE Lubrication: Oil and Oil Filter: Replacement” • 2008 / 2009 Land Cruiser: Engine/Hybrid System – Lubrication – “3UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 / 2010 Matrix: Engine/Hybrid System – Lubrication – “2ZR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 RAV4: Engine/Hybrid System – Lubrication – “2AR-FE Lubrication: Oil and Oil Filter: Replacement” • 2008 / 2009 / 2010 Sequoia (3UR-FE): Engine/Hybrid System – Lubrication – “3UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2010 Sequoia (1UR-FE): Engine/Hybrid System – Lubrication – “1UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2007 / 2008 / 2009 / 2010 Tundra (3UR-FE): Engine/Hybrid System – Lubrication – “3UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2010 Tundra (1UR-FE): Engine/Hybrid System – Lubrication – “1UR-FE Lubrication: Oil and Oil Filter: Replacement” • 2009 Venza: Engine/Hybrid System – Lubrication – “1AR-FE Lubrication: Oil and Oil Filter: Replacement”

Related entry:

2003 sable oil pan replacement, oilpumpchevyluminna1996, 17k707 replacement, removing oil pan on 2007 pontiac g5, pollen filter change 2009 corsa design, knee bolster for 04 deville, how to replace 2002 e250 rotor, e-90 aftermarket cupholders, 2011 tacoma chassis lube, 2010 tundra loud engine noise and over retarded on banks 1 and 2,