1997 mazda protege starter
You are searching repair manual in PDF format about 1997 mazda protege starter use another keyword for search another post or files
1997 mazda protege starter Direct Download speed 5787 Kb/s
1997 mazda protege starter Full Version speed 6767 Kb/s
Filed Under (Ford) by admin on 03-04-2011
Starter Motor Removal WARNING: WHEN PERFORMING MAINTENANCE ON THE STARTING SYSTEM BE AWARE THAT HEAVY GAUGE LEADS ARE CONNECTED DIRECTLY TO THE BATTERY. MAKE SURE PROTECTIVE CAPS ARE IN PLACE WHEN MAINTENANCE IS COMPLETE. WARNING: THE ELECTRICAL POWER TO THE AIR SUSPENSION SYSTEM MUST BE SHUT OFF PRIOR TO HOISTING, JACKING OR TOWING AN AIR SUSPENSION VEHICLE. THIS CAN BE ACCOMPLISHED BY TURNING OFF THE AIR SUSPENSION SWITCH LOCATED IN THE RH KICK PANEL AREA. FAILURE TO DO SO MAY RESULT IN UNEXPECTED INFLATION OR DEFLATION OF THE AIR SPRINGS WHICH MAY RESULT IN SHIFTING OF THE VEHICLE DURING THESE OPERATIONS. 1. Disconnect the battery ground cable. 2. Raise and support the vehicle; refer to Section 100-02 . 3. Remove the starter motor solenoid terminal cover (11N087). 4. NOTE: The 4.6L engine is shown; the 5.4L engine is similar. Disconnect the starter motor electrical connections. 1. Remove the nuts. 2. Remove the battery cable. 3. Remove the starter solenoid wire. 5. NOTE: The 4.6L engine is shown; the 5.4L engine is similar. Remove the (A) starter motor ground cable nut and the (B) starter motor ground cable. 6. Remove the starter. 1. Remove the two bolts. 2. Remove the starter. Installation WARNING: WHEN PERFORMING MAINTENANCE ON THE STARTING SYSTEM BE AWARE THAT HEAVY GAUGE LEADS ARE CONNECTED DIRECTLY TO THE BATTERY. MAKE SURE PROTECTIVE CAPS ARE IN PLACE WHEN MAINTENANCE IS COMPLETE. 1. Install the starter motor. 1. Position the starter motor. 2. Install the two bolts. 2. NOTE: The 4.6L engine is shown; the 5.4L engine is similar. Connect the (A) starter motor ground cable and install the (B) starter motor ground cable nut. 3. NOTE: The 4.6L engine is shown; the 5.4L engine is similar. Connect the starter motor electrical connections. 1. Position the starter solenoid wire. 2. Position the battery cable. 3. Install the two nuts. 4. Install the starter motor solenoid terminal cover. 5. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch. Lower the vehicle. 6. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy. Connect the battery ground cable.
Filed Under (volkswagen) by admin on 30-06-2011
1995-96 STARTING & CHARGING SYSTEMS Volkswagen Starters Cabrio, Golf III, GTI, Jetta III DESCRIPTION Starter is a brush type, series-wound electric motor with an overrunning clutch. Field frame is enclosed by commutator end frame and drive bushing, and carries pole shoes and field coils. A splined armature shaft drive end carries drive assembly. TROUBLE SHOOTING NOTE: ON-VEHICLE TESTING STARTER DOES NOT CRANK ENGINE 1) Ensure battery is fully charged. Ensure electrical and ground connections are clean and tight. With ignition switch in START position, measure voltage at spade terminal of starter solenoid. Reading should be at least 8 volts. If voltage is as specified, go to step 3). If voltage is not as specified, go to next step. 2) Measure voltage at ignition switch. If reading is at least 8 volts, check wiring between ignition switch and starter solenoid. If voltage is not as specified, replace ignition switch. 3) While operating starter, measure voltage at field (starter) terminal of starter solenoid. If reading is at least 8 volts, repair or replace starter. If reading is less than 8 volts, replace starter solenoid. NOTE: See TROUBLE SHOOTING article in GENERAL INFORMATION. On vehicles with automatic transmission, also check park/neutral switch. STARTER CRANKS TOO SLOWLY TO START ENGINE Ensure battery is fully charged. Ensure electrical and ground connections are clean and tight. If necessary, clean and tighten ground strap between transmission and body. DO NOT loosen ground strap on body. If starter still turns slowly, repair or replace starter. REMOVAL & INSTALLATION Removal & Installation 1) Disconnect negative battery cable. Support engine/transmission assembly with Support Beam (VW 10-222A) and Leg
Filed Under (KIA) by admin on 17-08-2010
Removal 1. Disconnect negative battery cable. 2. Remove the upper two bolts from the intake manifold bracket. 3. Raise vehicle and support. 4. 5. 6. 7. 8. Remove the two bolts on the clutch release cylinder and push aside (M/T). Remove the lower two intake manifold bracket bolts. Remove intake manifold bracket. Remove the two upper starter bolts. Remove the lower starter bolt. 9. 10. 11. 12. Pull the starter from the clutch (M/T) / torque converter (A/T) housing and prop in place. Lower the vehicle. From above, disconnect the S-terminal connector. Remove nut and lock washer on B-terminal. 13. 14. 15. 16. Disconnect B-terminal. Raise and support vehicle. Push transmission wire harness aside. Remove starter. Installation 1. Place starter in engine well. 2. Lower vehicle. 3. Connect B-terminal wire. 4. Install washer and nut on B-terminal and tighten. 5. Connect S-terminal. 6. 7. 8. 9. 10. Lower intake manifold bracket into position and insert the two upper bolts. Raise and support vehicle. Place starter in position. Insert the two upper starter bolts. Insert lower starter bolt. NOTE:: The starter may require adjustment after installation. If required, rotate the starter slightly to provide proper clearance. 11. Tighten the three starter bolts. Tighten the bolts to 27 – 40 lb-ft (37 – 54 N.m). 12. Insert lower bracket bolts and tighten. Tighten the bolts to 27 – 40 lb-ft (37 – 54 N.m). 13. Position clutch release cylinder and install bolts (M/T). Tighten the bolts to 27 – 40 lb-ft (37 – 54 N.m). 14. Lower vehicle.
Filed Under (volkswagen) by admin on 28-05-2010
2. Disconnect all wiring from starter solenoid. Remove starter cable from retainer. Remove starter wiring from guides. Remove guides. 3. Raise and support vehicle. Remove noise insulation panel. See Fig. 3 . Remove left-side insulation panel. See Fig. 4 . Remove brackets/retainers securing power steering pressure line. Place power steering pressure line aside. 4. Remove bolts securing starter. See Fig. 5 . Remove starter. To install, reverse removal procedure. Tighten starter mounting bolt/nuts to specification. See TORQUE SPECIFICATIONS . Fig. 4: Identifying Left-Side Noise Insulation Panel Mounting Points Fig. 5: Removing Starter
Filed Under (Jeep) by admin on 01-12-2010
CONDITION POSSIBLE CAUSE CORRECTION Very High Frequency Excessive distance between Shim starter motor toward Flywheel/Drive Whine Before Engine pinion gear and Flywheel/Drive Plate. Starts; Engine Starts OK. Plate gear. Very High Frequency Insufficient distance between Shim starter motor away from Whine After Engine Starts starter motor pinion gear and Flywheel/Drive Plate. Inspect With Ignition Key Flywheel/ Drive Plate runout Flywheel/Drive Plate for damage; bent, Released. Engine Starts can cause noise to be unusual wear, and excessive runout. OK. intermittent. Replace Flywheel/Drive Plate as necessary. A Loud “Whoop” After Probable cause is defective Replace starter motor. Engine Starts While Starter overrunning clutch. Motor is Engaged “Rumble”, “Growl”, or Probable cause is bent or Replace starter motor. “Knock” as Starter Motor unbalanced starter motor Coasts to Stop After armature. Engine Starts.