1998 MAZDA 626 BELT DIAGRAM


You are searching repair manual in PDF format about 1998 MAZDA 626 BELT DIAGRAM use another keyword for search another post or files



  1998 MAZDA 626 BELT DIAGRAM Direct Download speed 5787 Kb/s

  1998 MAZDA 626 BELT DIAGRAM Full Version speed 6767 Kb/s




Ford Escort, Fiesta, Sierra, Mondeo, P100, 1.8 Diesel/Turbo diesel Camshaft Belt / Fuel Injection Pump Belt Common Causes of Failure

0

Filed Under (Ford) by admin on 05-06-2011

download
Common causes of camshaft timing belt failure on the above vehicles are due to incorrect operating tension, or ingress of dirt, water, or debris entering the timing belt cover. Predominantly on Fiesta models a high percentage of camshaft timing belt failures occur after the ancillary poly ‘V’ drive belt has failed, where strands of material off the broken belt have entered the timing belt cover. This is especially so where an ancillary belt has been fitted that does not contain “Kevlar” based materials. It is therefore important to always remove the timing belt cover to check for belt debris if the ancillary belt has failed. Any contamination that enters the timing belt cover can become compressed between the surfaces of the camshaft timing belt and drive pulleys. This causes wear to both the belt teeth, backing surface, and damage to the drive pulleys, resulting in premature failure of the camshaft timing belt. Later engines have modifications to improve the sealing of the belt cover around the crankshaft pulley, to reduce the level of outside contamination. Incorrect tensioning of the belt during installation will adversely affect the life of the belt. Before fitting a new belt it is important to check and observe the following points :- 1) Right Hand Inner Wing Splash Shield (Fiesta, Escort, Mondeo) This must be fitted and undamaged. 2) Timing Belt Cover Check that all components of the cover are fitted and undamaged. Ensure the latest type of modified cover is fitted. 3) a) Toothed Drive Pulleys Check that the tooth profiles are not worn or damaged. On vehicles built before January 1994 special attention should be given to the nylon toothed pulley situated below the camshaft pulley in a clockwise position on the belt drive (see diag item 4). This should be changed to a modified steel pulley (Ford No. 7053802) plus bolt (6701537). Ensure that the Camshaft and Injection Pump sprockets are free to rotate on the drive locations when the retaining bolts are slackened off. b) 4) a) b) c) Water Pump, Idler and Tensioner Pulleys Check that the belt running surfaces are not worn or damaged. Check that the flanges are running true and not damaged. Check that the water pump, and pulley bearings are in good condition, to ensure correct belt alignment. 5) Crankshaft Pulley The toothed pulley is in two parts. The rear section (Injection Pump Drive) is located onto the crankshaft by a small drive pin. The front section (Camshaft and “Poly V” belt drive) engages onto the rear pulley via a small vee protrusion on the rear face. Should the central fixing bolt for the crankshaft pulley come loose, or an old bolt re-used (Stretch bolt design), it is possible for fretting to take place damaging the locations. The crankshaft and camshaft pulleys can then move out of timing alignment, resulting in valve and piston contact damage. Replacement Procedure As the vehicle is fitted with two timing belts, one to drive the Camshaft, and one to drive the Injection Pump drives, which are driven off the crankshaft pulley, it is strongly recommended that both belts are replaced at the same time. NOTE: Special tools are required to lock the crankshaft, camshaft, and injection pump in the correct angular location when changing the belts, to ensure correct timing position. IMPORTANT: Ensure the engine is cold (not run for 4 hours) before commencing working as this will affect the setting of the timing belt tension and could lead to premature failure. Continued . . . .

Related entry:

k4m timingbelt, 1980 corvette engine belts picture, 460 ford v belt diagram, 2002 hyundai accent timing belt loose on the front side, how to put fenbelt of corsa ven utility, izusu big horn 1996 alternator fan belt, ford transit t280 alternator belt removal;, remove the serpentine belt from a 2002 dodge intrepid 3 5 litre v6, serpentine belt diagram for 1988 Chevrolet 454, toyota 2 8Litre timing belt tensioning instructions,

1998 Jeep Cherokee Drive Belt: Service and Repair

0

Filed Under (Jeep) by admin on 03-01-2011

download
Correct drive belt tension is required to ensure optimum performance of the belt driven engine accessories. There are different types of adjustment gauges for checking either a serpentine or a V-type belt. Use the correct gauge when checking belt tension. Place gauge in the middle of the section of belt being tested (between two pulleys) to check tension. Do not allow the gauge (or gauge adapter) to contact anything but the belt. BELT SCHEMATICS The belt routing schematics are published from the latest information available at the tingle of publication. If anything differs between these schematics and the Belt Routing Label, use the schematics on Belt Routing Label. This label is located in the engine compartment. BELT REPLACEMENT OR ADJUSTMENT- LEFT HAND DRIVE Belt tension is adjusted at the power steering pump bracket and idler pulley assembly. 1. Disconnect negative battery cable from battery. 2. Loosen idler pulley bolt at the power steering bracket. 3. Loosen adjusting bolt until belt can be removed from pulleys. 4. Remove belt. INSTALLATION 1. Check condition of all pulleys. CAUTION: When installing the serpentine accessory drive belt, the belt MUST be routed correctly. If not, the engine may overheat due to the water pump rotating in the wrong direction. 2. Install new belt. 3. Using serpentine belt tension gauge, tighten adjusting bolt until belt reaches proper tension. Refer to Belt Tension at the rear of this section for proper belt tension. 4. After belt is tensioned correctly, tighten idler pulley bolt to 47 Nm (35 ft. lbs.) 5. After idler pulley has been tightened into position, recheck belt tension. Adjust if necessary. BELT REPLACEMENT OR ADJUSTMENT- RIGHT HAND DRIVE (4.0L) 1. Disconnect negative battery cable from battery. 2. Loosen lower alternator mounting bolt and nut. 3. Loosen upper alternator mounting nut. 4. Loosen adjusting bolt at upper alternator bracket until belt can be removed from pulleys. 5. Remove belt. INSTALLATION 1. Check condition of all pulleys.

Related entry:

2006 mazda tribute 4 cyl belt replacement schematic, how to replace serpentine belt on 2004 gmc envoy, 1993 v6 buick dynasty 3 0 belt images, GALAXY 1 9 TDI FANBELT ROUTE, belt routing ford fusion, 2003 ford 4 2 l belt routing, 2004 Lincoln LS vacuum line routing, belt replacement on 2008 HHR, serpentine belt diagram 2004 madza 6, diagram alternator belt 1989 gerwin van,

1998 Mazda 626 LX Air Flow Meter/ Sensor Using the NGS Tester

0

Filed Under (Mazda) by admin on 19-11-2010

download
1. Check the mass air flow sensor for damage and cracks. 2. Connect the New Generation Star tester to the data link connector. 3. Turn the ignition switch to ON. 4. Select the “PID/DATA MONITOR AND RECORD” function on the NGS tester display and press TRIGGER. 5. Select “MAF V” on the NGS tester display and press START. The NGS tester measures and show the voltage. 6. If not as specified, inspect the following. (1) Harness continuity Between PCM terminal 88 and mass air flow sensor terminal E Between PCM terminal 36 and mass air flow sensor terminal D Between PCM terminal 103 and mass air flow sensor terminal C Between main relay terminal E and mass air flow sensor terminal B (2) Terminal voltage Mass air flow sensor terminal B voltage: Battery positive voltage Mass air flow sensor terminal C voltage: Below 1.0 V 7. If the terminal voltage is correct and there is harness continuity, replace the mass air flow sensor.

Related entry:

93 corvette no start flow chart, Mass Air Flow Sensor location in 08 pacifica, no start diagnostic flow chart, no start flow chart,

1994 Ford Aerostar/Ranger/Explorer Camshaft Timing ADJUSTMENTS

0

Filed Under (Ford) by admin on 08-03-2011

download
Checking Timing An access plug is provided in the cam drive belt cover so that camshaft timing can be checked without removal of the cover or any other parts. 1. Remove the access plug from the cam drive belt cover. 2. Rotate the crankshaft so that the No. 1 piston is rising on compression stroke. 3. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TC mark on the belt cover. Always turn the engine in the direction of normal rotation (clockwise, as viewed from the front). Backward rotation may cause the timing belt to jump time, due to the arrangement of the belt tensioner. 4. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover. 5. Install the belt cover access plug. Adjusting Timing Belt SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Belt Tension Adjusting Tool T74P-6254-A 1. Remove the outer timing belt cover as outlined in this section. CAUTION: Attempting to adjust timing belt tension without loosening spring pivot bolt will break Crankshaft Belt Tension Adjusting Tool T74P-6254-A when relieving tension on the belt. 2. If belt timing or tension is incorrect, loosen timing belt spring pivot bolt. 3. Hold tensioner with Camshaft Belt Tension Adjusting Tool T74P-6254-A. 4. While holding tensioner, loosen adjusting bolt and gradually release spring tension. Loosening Timing Belt Tensioner, 2.3L Tool Number 8 — 5. Using adjusting tool, pry tensioner away from belt. While holding, tighten adjusting bolt. There should be no tension on belt. Camshaft Timing Belt, 2.3L I-4 Timing Mark on Camshaft Sprocket Remove the bolts holding the crankshaft position sensor in place and pull the sensor assembly free of the dowel pin. 7. Remove the crankshaft pulley , crankshaft pulley hub and timing belt guide. 8. Remove the drive belt and inspect it for wear or damage. If the belt is damaged, replace it. 9. Remove one spark plug from each cylinder. 10. If not done: a. Loosen tensioner adjusting bolt. b. Using Camshaft Belt Tension Adjusting Tool T74P-6254-A, pry tensioner clockwise against spring tension as far as possible. c. Tighten adjusting bolt to hold tensioner in released position. 11. Align crankshaft so number one piston is at TDC (top dead center) as indicated by timing mark. 12. Line up camshaft sprocket timing mark with inner timing belt cover timing mark and key is pointing down.

Related entry:

yhsm-imp1, 2008 ford edge timing belt or chain, fit cam belt toyota hiace, belt diagram 2006 monte carlo 3 5 motor, lexus is200 timing procedure, how to tighten a fan belt on a citron billing go van, top dead center timing belt 91 ford ranger 2 3, TOYOTA FUNCARGO ENGINE TIMING MARKS, 4jg2 engine timing mark diagrams, ford edge timing belt or chain,

1993-1997 Peugeot 306 Timing belt replacement intervals

0

Filed Under (Peugeot) by admin on 14-11-2010

download
Removal Removal 1. Raise and support front of vehicle. 2. Remove: RH front wheel. Engine undershield (if fitted). Lower inner wing panel. Auxiliary drive belt(s). 307: Engine tie-bars. Crankshaft pulley [1] . Timing belt upper cover [2] . Timing belt centre cover [3] . Timing belt lower cover [4] . 3. Turn crankshaft to setting position. Insert timing pins in camshaft sprocket and flywheel [5] & [6] . 4. Slacken tensioner nut to release tension on belt [7] . Lightly tighten nut. 5. Remove timing belt. Installation – -1997 Installation – -1997 1. Ensure timing pins located correctly [5] & [6] . 2. Fit timing belt in following order: Crankshaft sprocket. Camshaft sprocket. Water pump sprocket. NOTE: Ensure belt is taut between sprockets on non-tensioned side. Slacken tensioner nut [7] . Turn tensioner anti-clockwise to tension belt. Temporarily tighten nut. Remove timing pins [5] & [6] . Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. Slacken tensioner nut [7] . Tension belt as follows: Turn tensioner anti-clockwise until tension gauge indicates 45 SEEM units. Tighten tensioner nut to 20 Nm [7] . Remove tension gauge. Turn crankshaft four turns clockwise to setting position. Ensure timing pins can be inserted [5] & [6] . Wait 1 minute to allow belt to settle. Apply firm thumb pressure to belt at . Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. Slacken tensioner nut [7] . Turn tensioner anti-clockwise to tension belt. New belt: 40 SEEM units. Used belt: 36 SEEM units. Tighten tensioner nut to 20 Nm [7] . Remove tension gauge [8] . Turn crankshaft two turns clockwise. Ensure flywheel timing pin can be inserted [6] . NOTE: DO NOT allow crankshaft to turn anti-clockwise. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. Check tension gauge reading. New belt: 51±3 SEEM units. Used belt: 45±3 SEEM units. Install components in reverse order of removal. Tighten crankshaft pulley bolts to 8 Nm [9] . 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25.

Related entry:

tensiometre seem c tronic 105 5, twenty-four valve engine,