1998 dodge dakota air blower motor


You are searching repair manual in PDF format about 1998 dodge dakota air blower motor use another keyword for search another post or files



  1998 dodge dakota air blower motor Direct Download speed 5787 Kb/s

  1998 dodge dakota air blower motor Full Version speed 6767 Kb/s




2005 Buick Allure Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off

0

Filed Under (Buick) by admin on 17-12-2010

download
Condition Some customers may comment on an inoperative or intermittent Heating, Ventilation and Air Conditioning (HVAC) blower motor. Others may comment that the blower motor speed may momentarily drop or that the blower motor continues to run after the key is turned off. Cause This condition may be caused by a voltage spike from the wiper motor. The voltage spike may cause a logic lock up in the blower motor control module that may be either momentary or permanent. Correction DO THIS DON’T DO THIS Install a Capacitor at the Blower Motor Control Module Connector Technicians are to install a capacitor, P/N 25073556, at the blower motor control module connector using the following procedure: 1. Disconnect the negative cable from the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 2. Remove the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement-Right procedure in the Instrument Panel, Gages and Console section of SI. DO NOT replace the Blower Motor Control Module, Blower Motor or the HVAC Control Head

2002 Cadillac DeVille Blower Motor Replacement REMOVAL PROCEDURE

0

Filed Under (Cadillac) by admin on 30-09-2010

download
1. 2. 3. 4. 5. 6. Remove the right side sound insulator. Pull back the carpet near the blower motor. Remove the IP compartment. Remove the dash integration module from the bracket. Remove the two rear dash integration module bracket fasteners. Reposition the dash integration module bracket in order to remove the blower motor. 7. Disconnect the electrical connector (2) from the blower motor. 8. Remove the blower motor retaining fasteners (1). 9. Rotate and remove the blower motor from the vehicle. INSTALLATION PROCEDURE Rotate the blower motor in order to install the blower motor into the housing. 1. Install the blower motor into the blower motor housing. 2. Ensure that the blower motor gasket is properly aligned. NOTE: Refer to Fastener Notice in Service Precautions. 3. Install the blower motor retaining screws (1). Tighten Tighten the screws to 1.4 N.m (12 lb in). 4. Connect the electrical connector (2) to the blower motor.

1994 Ford Thunderbird A/C BLOWER MOTOR SPEED CONTROL NOT OPERATING CORRECTLY

0

Filed Under (Ford) by admin on 06-03-2011

download
C1 CHECK BLOWER MOTOR SUPPLY VOLTAGE Gain access to the blower motor control connector. Turn ignition switch to the ON position. Using a voltmeter, check voltage at Circuit 687 (GY/Y) at motor connector. Is voltage 10 volts or more? Yes GO to C4. No GO to C2. C2 CHECK CIRCUIT 687 (GY/Y) FOR SHORT Remove blower Fuse 30A at primary junction block. Using an ohmmeter connected to a known good ground, connect second lead to Circuit 687 (GY/Y) at A/C blower motor. Measure resistance. Is resistance 5 ohms or less? Yes SERVICE Circuit 687 (GY/Y) for short. REPLACE fuse. RESTORE vehicle. RETEST system. No GO to C3. C3 CHECK CIRCUIT 687 (GY/Y) FOR OPEN Disconnect A/C blower motor control. Connect a jumper wire to Circuit 687 (GY/Y) at blower motor control connector. Connect other end to a known good ground. Using an ohmmeter connected to a known good ground, connect second lead to Circuit 687 (GY/Y). Measure resistance. Is resistance 5 ohms or less? Yes GO to C4. No SERVICE Circuit 687 (GY/Y) for open. RESTORE vehicle. RETEST system. C4 CHECK BLOWER MOTOR SPEED CONTROL GROUND Gain access to A/C blower motor speed control as outlined. Using an ohmmeter connected to a known good ground, connect second lead to Circuit 57 (BK) at A/C blower motor speed control connector, J1-2. Measure resistance. Is resistance 5 ohms or less? Yes

2007 – 2008 Toyota Yaris Blower Motor Noise &Vibration

0

Filed Under (Toyota) by admin on 20-09-2010

download
noise or a slight vibration when operating the blower motor due to foreign objects or debris in the blower unit. Follow the repair procedure in this TSB to correct this condition.Repair Procedure 1. Remove the blower motor. Refer to the Technical Information System (TIS), applicable model year Yaris Repair Manual: 2007 or 2008 Yaris, Vehicle Interior – Heating/Air Conditioning – “Air Conditioning: Blower Motor: Removal”. 2. Inspect the blower motor for evidence of foreign objects or debris. • If foreign objects or debris are noticed in the blower motor, remove debris or foreign object, reinstall the blower motor, verify proper operation, and continue to step 3. • If NO foreign objects or debris is noticed in the blower motor, investigate the root cause of the blower motor noise and vibration, replace as necessary, and continue to step 3. 3. Remove the glove box. Refer to TIS, applicable model year Yaris Repair Manual: 2007 Yaris Hatchback, Vehicle Interior – Interior Panels/Trim – “Instrument Panel: Upper Instrument Panel (for Hatchback): Removal”. 2007 Yaris Sedan, Vehicle Interior – Interior Panels/Trim – “Instrument Panel: Upper Instrument Panel (for Sedan): Removal”.

2001 Dodge Durango BLOWER MOTOR RELAYS test

0

Filed Under (Dodge) by admin on 07-12-2010

download
1. Disconnect negative battery cable. On 2000 Dakota, blower motor relay is located behind instrument panel, inboard of glove box. See Fig. 1 . On 2000 Durango, Ram Pickup, Ram Van/Wagon, front blower motor relay is located in Power Distribution Center (PDC). 2. On Ram Van/Wagon, front high speed blower motor relay is located in engine compartment, on top cover of on inboard side of heater housing assembly. See Fig. 2 . Rear blower motor relay and rear high speed blower motor relay are located in a connector bracket that is secured to back of rear A/C-heater unit cover. See Fig. 3 . 3. On all models, remove suspect blower motor relay or high speed blower motor relay. Using DVOM, check for continuity between terminals No. 87A and 30 of relay. See Fig. 4 . If continuity does not exist, replace relay. If continuity exists, go to next step. 4. Using DVOM, check for continuity between terminals No. 30 and 87 of relay. See Fig. 4 . If continuity exists, replace relay. If continuity does not exist, go to next step. 5. Measure resistance between terminals No. 85 and 86 of relay. See Fig. 4 . Reading should be 70-80 ohms. If reading is not as specified, replace relay. If reading is as specified, go to next step. 6. Using jumper wires, connect battery voltage to terminal No. 86 and ground terminal No. 85. See Fig. 4 . Check that continuity exists between terminals No. 30 and 87. Check that continuity does not exist between terminals No. 87A and 30. If continuity is not as specified, replace blower motor relay. If continuity is as specified, relay is okay.