Filed Under (Chrysler, Dodge) by admin on 28-09-2009
repair manual covers Chrysler Cirrus, Sebring; Dodge Avenger, Stratus; Plymouth Breeze. US and Canadian models, 1995 to 1998.
What’s Inside?
Introduction: Vehicle identification numbers; Buying parts; Maintenance techniques, and more. Tune-up and routine maintenance; Engine and overhaul procedures; Cooling, heating and air-conditioning systems; Fuel and exhaust systems; Engine electrical systems; Emissions control systems; Transmission; Brakes; Suspension and steering systems; Body; Chassis electrical system; Wiring diagrams.
Filed Under (Dodge) by admin on 25-09-2010
download
1. Raise vehicle on hoist. 2. Remove brake line mounting nut and remove the brake line from the sensor stud. 3. Remove mounting stud from the sensor and shield. 4. Remove sensor and shield from differential housing. 5. Disconnect sensor wire harness and remove sensor. INSTALLATION 1. Connect harness to sensor. Be sure seal is securely in place between sensor and wiring connector. 2. Install O-ring on sensor (if removed). 3. Insert sensor in differential housing. 4. Install sensor shield. 5. Install the sensor mounting stud and tighten to 24 Nm (18 ft. lbs.). 6. Install the brake line on the sensor stud and install the nut. 7. Lower vehicle.
Filed Under (Cadillac) by admin on 03-09-2010
download
1. Remove two-thirds of the brake fluid from the master cylinder. Raise the vehicle and suitably support. 3. Mark the relationship of the wheel to the axle flange. 4. Remove the Wheel. IMPORTANT: Do not use a screwdriver or pry bar to compress the caliper piston into the caliper. Any damage to the piston boot could cause corrosive elements to enter the piston sealing area and lead to the piston seizing in the caliper bore. 5. Using a large C clamp compress the caliper piston into the caliper bore completely. 6. Remove the bottom caliper slide pin. 7. Pivot the caliper body upward. 8. Remove the inboard and outboard pads from the anchor bracket. 1998 Cadillac DeVille V8-4.6L VIN Y 9. Remove and inspect the pad retainers. IMPORTANT: Inspect the caliper bolt suspension boots for cuts, tears, or deterioration. If damaged, replace the pin boots. Refer to “Brake Caliper Bracket Overhaul” in Brake Caliper. Inspect the piston boot for deterioration. If damaged, Refer to “Brake Caliper Overhaul” in Brake Caliper. Inspect the Caliper pin bolt for damage or corrosion. Replace if damaged or corroded. Do Not attempt to clean away corrosion. Corrosion is typically caused by damaged pin boots. INSTALLATION PROCEDURE
Filed Under (Chrysler, Dodge) by admin on 28-09-2009
repair and service manual covers Chrysler Sebring convertible, coupe and sedan 1995-2005, Dodge Stratus coupe and sedan 2001-2005, and Dodge Avenger 1995 to 2000.
Note: this manual DOES NOT include information specific to Flexible Fuel Vehicles.
What’s Inside
* Introduction: Vehicle identification numbers; Buying parts; Maintenance techniques, and more. * Tune-up and routine maintenance * Four-cylinder engine * 2.5L and 3.0L V8 engines * 2.7L V6 engine * General engine overhaul procedures * Cooling, heating and air-conditioning systems * Fuel and exhaust systems * Engine electrical systems * Emissions and engine control systems * Manual and automatic transaxle * Clutch and driveaxles * Brakes * Suspension and steering systems * Body * Chassis electrical system * Wiring diagrams
Filed Under (Chrysler, Dodge) by admin on 28-09-2009
repair and service manual covers all Chrysler LHS, Concorde, 300M and Dodge Intrepid models, from 1998 through 2003.
Table of Contents
Introductory pages
About this manual | Introduction to the Chrysler LHS, Concorde, 300M, and Dodge Intrepid | Vehicle identification numbers | Buying parts | Maintenance techniques, tools and working facilities | Jacking and towing | Booster battery (jump) starting | Automotive chemicals and lubricants | Conversion factors | Fraction/decimal/millimeter equivalents | Safety first! | Troubleshooting
