1998 ford explorer coolant system diagram
You are searching repair manual in PDF format about 1998 ford explorer coolant system diagram use another keyword for search another post or files
1998 ford explorer coolant system diagram Direct Download speed 5787 Kb/s
1998 ford explorer coolant system diagram Full Version speed 6767 Kb/s
Filed Under (Pontiac) by admin on 17-01-2011
Subject: Models: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue Condition Some customers may comment that the low engine coolant level indicator is always illuminated. Cause The cause of this condition may be due to engine oil contaminating the coolant. Possible sources of oil contamination are internal engine leaks, improper service procedures, or the addition of some types of anti-leak additives to the cooling system. Once in the coolant, the oil leaves deposits on the level sensor creating an insulating film. This film results in a false activation of the coolant level indicator. Correction Diagnose low coolant level system operation and check the sensor for oil contamination using the procedure listed below. Important: No coolant supplements should be used in GM cooling systems, other than what is approved and recommended by GM. The use of “aftermarket” over-the-counter sealing and cooling supplements may affect the operation of the low coolant level sensor. Discoloration of the coolant recovery bottle is normal and does not necessarily indicate that coolant contamination is present. Flush cooling system only when instructed by this bulletin. 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • Light is out — Proceed to Step 4.
Filed Under (Ford, Lincoln) by admin on 17-10-2009
The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford Escape / Mercury Mariner 2007-2009 Ford Expedition / Lincoln Navigator 2006-2009 Ford Explorer / Lincoln Aviator / Mercury Mountaineer 2007-2008 Ford F150, F250, and F350 / Lincoln Mark LT
2009 Ford Flex 2008-2009 Ford Focus 2006-2007 Ford Freestar / Mercury Monterey 2008-2009 Ford Fusion / Lincoln MKZ / Mercury Milan 2007-2009 Ford Mustang 2007-2009 Ford Ranger 2008-2009 Ford Taurus / Mercury Sable
1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard). 2. Turn the ignition switch to OFF then press and release the brake pedal. 3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds. 4. Press and release the brake pedal
Filed Under (Ford) by admin on 07-01-2011
Draining 1. Bring the engine to normal operating temperature and turn the engine off. With the cooling system under pressure, inspect cooling system hoses and clamped hose connections for leaks, excessive deterioration or contact wear. Inspect radiator installation retention. Note any discrepancies and proceed. 2. WARNING: Never remove the pressure relief cap while the engine is operating or when the cooling system is hot. Failure to follow these instructions can result in damage to the cooling system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of the degas bottle when removing the pressure relief cap, wait until the engine has cooled, then wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the pressure is released from the cooling system. When you are sure all the pressure has been released, (still with a cloth) turn and remove the pressure relief cap. CAUTION: The coolant must be recovered in a suitable, clean container for reuse. If the coolant is contaminated, it must be recycled or disposed of correctly and replaced. CAUTION: Some vehicle cooling systems are filled with Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A (green color). Others are filled with Motorcraft Premium Gold Engine Coolant VC-7-A meeting Ford specification WSS-M97B51-A1 (yellow color). Always fill the cooling system with the same coolant that is present in the system. Do not mix coolant types. NOTE: Less than 80 percent of coolant capacity can be removed from the engine. Dirty, rusty or contaminated coolant requires replacement. Drain engine coolant as follows: Open radiator draincock to drain the coolant system. Disconnect radiator overflow hose from radiator filler neck connection. Remove radiator coolant recovery reservoir and empty the fluid. Flush radiator coolant recovery reservoir with clean water. Drain and reinstall radiator coolant recovery reservoir and radiator overflow hose and clamp to radiator filler neck. Correct, repair or install new components found to be inoperative in Step 1. Filling and Bleeding with RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling and Bleeding without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level in the degas bottle. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system:
Filed Under (Ford) by admin on 07-09-2010
FORD: 2005 Mustang 2004-2005 F-150 2005 Expedition, F-250, F-350 This article supersedes TSB 05-15-8 to update the Service Procedure. ISSUE Some vehicles equipped with a 4.6L 3-valve or 5.4L 3-valve engine may exhibit a ticking and/or knocking noise after reaching normal operating temperature. The noise may be described as “ticks”, “taps”, “knocks”, or “thumps”. In some cases the noise may be a normal characteristic of these engines. In other cases the noise may require further investigation. Sorting out and defining the noise as reported by the customer is important to successfully diagnose and/or repair the condition. ACTION Before starting diagnosis, it is critical to determine the specific engine noise the customer is concerned with. The customer should be interviewed to get their detailed perception and description of the noise, and to determine if the noise occurs at idle or above idle speed, and if the engine is cold, hot, or both. Attempt to duplicate the noise, and determine the source of the symptom. Refer to the following Service Procedure to help determine the source of the noise and if a repair is needed. LINCOLN: 2005 Navigator PRE-CHECKS 1. 2. 3.
Filed Under (Jaguar) by admin on 02-09-2010
Vehicles without supercharger 1. NOTE: Cap the vent hose to minimize coolant loss. Detach the coolant expansion tank. ^ Detach the vent hose. ^ Remove the coolant expansion tank retaining bolt. Vehicles with supercharger 2. NOTE: Cap the vent hoses to minimize coolant loss. Detach the coolant expansion tank. ^ Detach the vent hoses. ^ Remove the coolant expansion tank retaining bolt. 2003 Jaguar S-Type V8-4.2L All vehicles 3. Detach the coolant expansion tank. 4. Disconnect the coolant expansion tank low level sensor. 5. NOTE: Make sure the retaining clip is not removed. NOTE: Cap the coolant expansion tank lower hose to minimize coolant loss. Detach the coolant expansion tank lower hose. ^ Remove the coolant expansion tank.