1999 kia sportage electrical diagram
You are searching repair manual in PDF format about 1999 kia sportage electrical diagram use another keyword for search another post or files
1999 kia sportage electrical diagram Direct Download speed 5787 Kb/s
1999 kia sportage electrical diagram Full Version speed 6767 Kb/s
Filed Under (Toyota) by admin on 28-09-2009
ELECTRICAL WIRING DIAGRAM
This Service Bulletin is to inform you of the Electrical Wiring Diagram for RAV4 equipped with 1CD-
FTV engine.RELAY LOCATIONS ELECTRICAL WIRING ROUTING OVERALL ELECTRICAL WIRING DIAGRAM CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
Filed Under (Ford) by admin on 15-02-2011
CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Remove the steering wheel. Refer to Section 211-04. 2. Remove the passenger side air bag module. Refer to Section 501-20B. 3. Disconnect the antenna in-line connector. 4. Remove the RH instrument panel reinforcement bolt. 5. Close the glove compartment. 6. Remove the utility compartment. 1. Remove the four two part pin type retainers. 2. Remove the utility compartment. Disconnect the power point electrical connector. 7. If equipped, disconnect the compact disc changer electrical connector. 8. Release the compact disc changer electrical connector locator. 9. Remove the LH and RH scuff plates. 10. Remove the LH and RH A-pillar lower trim panels. 11. Position the LH and RH front door weatherstrip seals aside. 12. Remove the RH ground bolts. 13. If equipped, remove LH and RH instrument panel lower insulators. 14. Remove the instrument panel lower steering column opening cover. 1. Remove the screws. 2. Remove the instrument panel lower steering column opening cover. 15. Remove the instrument panel opening cover reinforcement. 1. Remove the bolts. 2. Remove the instrument panel opening cover reinforcement. 16. Disconnect the LH wiring harness electrical connectors. 17. Disconnect the electronic crash sensor (ECS) electrical connector. 1. Release the locking clip. 2. Disconnect the ECS electrical connector.
Filed Under (KIA) by admin on 04-06-2010
Description This bulletin provides information related to the Throttle Position Sensor (TPS) for Sorento & Sedona models. Some Sorento & Sedona vehicles may exhibit diagnostic trouble codes P0121 and/or P1121. This condition mainly occurs in high ambient or desert areas, and can be related to the occasional increase in contact resistance due to excessive wear of the inner elements of the TP sensor. This bulletin describes the proper service and adjustment procedure for replacing the TP Sensor. – Service Procedure Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor.
Filed Under (Ford) by admin on 27-04-2010
FORD: 1990-1997 THUNDERBIRD 1990-1999 MUSTANG, TAURUS SHO 1991-1999 CROWN VICTORIA, ESCORT, TAURUS 1992-1994 TEMPO 1993-1997 PROBE 1995-1999 CONTOUR 1990 BRONCO II 1990-1997 AEROSTAR 1990-1999 RANGER 1991-1999 EXPLORER 1994-1996 BRONCO 1994-1997 F SUPER DUTY, F-250 HD 1994-1999 ECONOLINE, F-150, F-250 LD, F-350 1995-1999 WINDSTAR 1997-1999 EXPEDITION 1999 F-250 HD, SUPER DUTY F SERIES
LINCOLN: 1991-1999 CONTINENTAL, TOWN CAR 1993-1998 MARK VIII 1998-1999 NAVIGATOR
MERCURY: 1990-1997 COUGAR 1991-1999 GRAND MARQUIS, SABLE, TRACER 1992-1994 TOPAZ 1995-1999 MYSTIQUE 1997-1999 MOUNTAINEER
ISSUE SERVICE TIP
This TSB article is a diagnostic procedure to address vehicles that exhibit lean driveability MASS AIR FLOW (MAF) DISCUSSION symptoms and may or may not have any Diagnostic MAF sensors can get contaminated from a variety Trouble Codes (DTCs) stored in memory. of sources: dirt, oil, silicon, spider webs, potting
compound from the sensor itself, etc. When a MAF sensor gets contaminated, it skews the transfer Follow the diagnostic procedures described in the function such that the sensor over-estimates air flow following Service Tip. The revised diagnostic at idle (causes the fuel system to go rich) and procedure is a more accurate means of diagnosing under-estimates air flow at high air flows (causes
the symptoms. fuel system to go lean). This means Long Term Fuel Trims will learn lean (negative) corrections at idle and learn rich (positive) corrections at higher air flows.
Filed Under (Rover) by admin on 23-05-2010
There are many problems with the BeCM (Body Electrical Control Module) fitted to late model (from 1995) Range Rover and Discovery. Click here to see photographs of this unit. The BeCM controls virtually EVERY electrical function on the vehicle and problems within the
BeCM (or its associated fuse box) will cause mis-operation of vehicle electrical functions. When diagnosing electrical problems on vehicles fitted with BeCM, it is vital to appreciate the relationship between the BeCM and its associated electrical fuse box which is located in the engine compartment.