Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
1998-99 MANUAL TRANSMISSIONS Volkswagen/Audi V.A.G. Type 02J 1998-99; Beetle 1999; Golf, Jetta IDENTIFICATION Volkswagen Audi Group (VAG) transaxle is identified by a type number cast into transaxle case. Three letter suffix identifies model. Code letter and production date information is stamped on a machined surface located inside the start mounting area and on upper portion of transaxle clutch housing surface. DESCRIPTION Type 02J is a 5-speed transaxle consisting of an input shaft, mainshaft/drive pinion and a differential assembly which transfers power to front wheels. LUBRICATION Place vehicle on level surface. Remove sound insulation below transmission, if equipped. Remove filler plug. Oil level should be to bottom of filler opening. Add fluid as needed. Use synthetic gear oil (G50, SAE 75W/90). Capacity is 2.1 qts. (2.0L).

Service and Repair Manual. Models covered. VW Golf & Jetta
VW Golf & Jetta Service and Repair Manual
Models covered
VW Golf & Jetta Mk 2 models with petrol engines, including fuel injection, catalytic converter,
Formel E, 16-valve and special/limited edition models 1043 cc, 1272 cc, 1595 cc & 1781 cc
Covers mechanical features of Van. Does not cover Convertible, Rallye, Caddy, diesel engine, 4 -wheel drive, Mk 1 models
or new Golf range introduced in February 1992

download

download
1995-96 STARTING & CHARGING SYSTEMS Volkswagen Starters Cabrio, Golf III, GTI, Jetta III DESCRIPTION Starter is a brush type, series-wound electric motor with an overrunning clutch. Field frame is enclosed by commutator end frame and drive bushing, and carries pole shoes and field coils. A splined armature shaft drive end carries drive assembly. TROUBLE SHOOTING NOTE: ON-VEHICLE TESTING STARTER DOES NOT CRANK ENGINE 1) Ensure battery is fully charged. Ensure electrical and ground connections are clean and tight. With ignition switch in START position, measure voltage at spade terminal of starter solenoid. Reading should be at least 8 volts. If voltage is as specified, go to step 3). If voltage is not as specified, go to next step. 2) Measure voltage at ignition switch. If reading is at least 8 volts, check wiring between ignition switch and starter solenoid. If voltage is not as specified, replace ignition switch. 3) While operating starter, measure voltage at field (starter) terminal of starter solenoid. If reading is at least 8 volts, repair or replace starter. If reading is less than 8 volts, replace starter solenoid. NOTE: See TROUBLE SHOOTING article in GENERAL INFORMATION. On vehicles with automatic transmission, also check park/neutral switch. STARTER CRANKS TOO SLOWLY TO START ENGINE Ensure battery is fully charged. Ensure electrical and ground connections are clean and tight. If necessary, clean and tighten ground strap between transmission and body. DO NOT loosen ground strap on body. If starter still turns slowly, repair or replace starter. REMOVAL & INSTALLATION Removal & Installation 1) Disconnect negative battery cable. Support engine/transmission assembly with Support Beam (VW 10-222A) and Leg

download
Inspection and Verification 1. Verify the customer’s concern by operating the climate control system to duplicate the condition. 2. Inspect to determine if one of the following mechanical or electrical concerns apply: Visual Inspection Chart Loose, missing or damaged A/C compressor drive belt. Loose or disconnected A/C clutch. Loose, misrouted or damaged vacuum lines. Broken or leaking vacuum control motora Discharged A/C system. Broken or leaking refrigerant lines. a a A leak in the vacuum control circuit may occur during acceleration (slow leak), may exist at all times (large leak), and may exist only when specific functions are selected (indicating a leak in that portion of the circuit). The vacuum hoses used in the passenger compartment control circuit are constructed from PVC plastic material. The vacuum hoses used in the engine compartment are constructed of Hytrel®. Because of the materials used, never pinch the vacuum hoses off during diagnosis to locate a leak. A wood golf tee can be used as a plug when it is necessary to plug one end of the vacuum hose for leak test purposes. 3. If the inspection reveals obvious concern(s) that can be readily identified, service as required. 4. If equipped with the electronic automatic temperature control system, go to Step 6. 5. If equipped with a manual A/C system, determine the symptom and go to the Symptom Chart. 6. If the concern remains after the inspection, connect the Rotunda New Generation Star (NGS) Tester to the data link connector (DLC) located beneath the instrument panel to carry out the DATA LINK DIAGNOSTICS test. If the NGS responds with NO RESPONSE/NOT EQUIPPED for the electronic automatic temperature control module, GO to Pinpoint Test A. If the DATA LINK DIAGNOSTICS test is passed for the electronic automatic temperature control module, retrieve the continuous DTCs and execute the Self-Test Diagnostics for the electronic automatic temperature control module to retrieve the current DTCs. Mechanical Electrical Open fuses. Blower motor inoperative. A/C compressor inoperative. Circuitry open/shorted. Disconnected electrical connectors. 7. If the self-test is passed and no DTCs are retrieved, go to the Symptom Chart to continue diagnostics. 8. If DTCs are retrieved, go to the Electronic Automatic Temperature Control (EATC) Module Diagnostic Trouble Code (DTC) Index to continue diagnostics. 9. If the electronic automatic temperature control module cannot be accessed by the NGS, GO to Pinpoint Test A. Electronic Automatic Temperature Control Module Self-Test The EATC module self-test will not detect concerns associated with data link messages like engine coolant temperature or vehicle speed signals. A NGS tester must be used to retrieve these concerns. The EATC module self-test will detect concerns in the system control functions and will display hard diagnostic trouble codes (DTCs) in addition to intermittent diagnostic trouble codes for concerns that occur during system operation. The vehicle interior temperature should be between 4-32° (40-90°F) when performing the self-test. If the temperatures are C not within the specified ranges, false in-car temperature sensor DTCs will be displayed. The self-test can be initiated at any time. Normal operation of the system stops when the self-test is activated. To enter the self-test, press the OFF and FLOOR buttons simultaneously and then press the AUTOMATIC button within two seconds. The display will show a pulse tracer going around the center of the display window. The test may run as long as 30 seconds. Record all DTCs displayed. If any DTCs appear during the self-test, follow the diagnostics procedure given under ACTION for each DTC given. If a condition exists but no DTCs appear during the self-test, refer to the Symptom Chart Condition: The EATC System Is Inoperative, Intermittent or Improper Operation. To exit self-test and retain all intermittent DTCs, push the blue (cooler temperature) button. The control will exit self-test, retain all intermittent DTCs and then turn OFF (display blank). To exit self-test and clear all DTCs, press the DEFROST button. The vacuum fluorescent display window will show 888 and all function symbols for one second. Then, the EATC control assembly will turn OFF (display blank) and all DTCs will be cleared. Always exit the self-test before powering the system down (system turned OFF). Intermittent DTCs will be deleted after 80 ignition switch ON cycles after the intermittent condition occurs.

download
Removal WARNING: WHEN DRAINING FUEL FROM THE FUEL TANK, KEEP SPARKS, SMOKING MATERIALS, AND OPEN FLAMES AWAY FROM THE VEHICLE. WARNING: THE FUEL SYSTEM CONTAINS PRESSURIZED FUEL AFTER THE VEHICLE IS SHUT DOWN AND WILL MAINTAIN THE PRESSURE FOR A LONG PERIOD OF TIME. 1. Relieve the fuel pressure; refer to Section 310-00. 2. Disconnect the battery ground cable (14301); refer to Section 414-01. 3. Raise and support the vehicle; refer to Section 100-02. 4. Disconnect the fuel tank filler pipe hose (9047) from the fuel tank (9002). 5. Drain the fuel from the fuel tank (9002); refer to Section 310-00. 6. Disconnect the fuel tank vent tube (9A228) from fuel tank filler pipe (9034). 7. Disconnect the fuel pump electrical connector. 8. If equipped, remove fuel tank skid plate. 1. Remove the five fuel tank skid plate bolts. 2. Lower the fuel tank skid plate. 9. Position a suitable jack under the fuel tank (9002). 10. Remove the front fuel tank support strap (9092). 1. Remove the two bolts. 2. Remove the front fuel tank support strap (9092). 11. Remove the rear fuel tank support strap (9092). 1. Remove the three bolts. 2. Remove the rear fuel tank support strap. 12. Partially lower the fuel tank and disconnect the two EVAP emissions hoses. 13. Remove the two safety clips from the fuel lines. 14. Disconnect the fuel lines from the fuel pump (9350). 1. Install and push the (A) fuel line disconnect tool into the (B) female fitting. 2. Separate the male and female fitting. 15. Remove the fuel tank.