2000 chevrolet silverado heating system
You are searching repair manual in PDF format about 2000 chevrolet silverado heating system use another keyword for search another post or files
2000 chevrolet silverado heating system Direct Download speed 5787 Kb/s
2000 chevrolet silverado heating system Full Version speed 6767 Kb/s
Filed Under (Chevrolet) by admin on 20-01-2011
Vehicle Application: Customer Concern: Tests/Procedures: Potential Causes: Diagnostic Codes: 2002 GAS, 2003 GAS, Chevrolet Silverado 1500 4.8L, Vin V, Eng Cfg V8, USA/Canada Chevrolet Silverado 1500 4.8L, Vin V, Eng Cfg V8 The engine runs, but lacks power when driving. Has codes P0101 and P0300. Scanner shows misfires all on the same side of the engine. 1. Check the catalytic converter, on the “suspect” bank of the engine, for a restricted (plugged) exhaust system to that side of the engine. 2. Disconnect both front O2 sensors, re-set the fuel trims and see if the problem goes away. 3. If gone with the O2 sensors disconnected, then swap the sensors side to side and see if the problem follows the O2 sensor. Plugged Exhaust System Oxygen Sensor P0101, P0300 2003 Chevrolet Tahoe 4.8L, GAS, Vin V 2003 Chevrolet Tahoe 5.3L, FLEX, Vin Z
Filed Under (Pontiac) by admin on 17-01-2011
Subject: Models: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue Condition Some customers may comment that the low engine coolant level indicator is always illuminated. Cause The cause of this condition may be due to engine oil contaminating the coolant. Possible sources of oil contamination are internal engine leaks, improper service procedures, or the addition of some types of anti-leak additives to the cooling system. Once in the coolant, the oil leaves deposits on the level sensor creating an insulating film. This film results in a false activation of the coolant level indicator. Correction Diagnose low coolant level system operation and check the sensor for oil contamination using the procedure listed below. Important: No coolant supplements should be used in GM cooling systems, other than what is approved and recommended by GM. The use of “aftermarket” over-the-counter sealing and cooling supplements may affect the operation of the low coolant level sensor. Discoloration of the coolant recovery bottle is normal and does not necessarily indicate that coolant contamination is present. Flush cooling system only when instructed by this bulletin. 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • Light is out — Proceed to Step 4.
The following diagnostics might be helpful if the vehicle exhibits the conditlon(s) described above. Use the appropriate recommendation based on what symptom has occurred. Recommendation/Instructions No DTCs Review Corporate Bulletin Number 05-02-32-002B to assure you do not have a blown 60 amp steering fuse. The fuse can be blown during improper jump starting of the vehicle on the HHR and ION. Check for this particularly for tow in conditions. DO NOT replace the steering column unless an internal short has been Identified in the column that is causing fuse to blow. Power Steering Warning Message on DIC with DTCs C0176 and C0476 This condition is often the result of excessive lock-to-lock turns of the steering wheel, causing the thermal protection in the Power Steering Control Module (PSCM) to take the steering motor temporarily off line. This is a normal operating characteristic of the system. DO NOT replace the steering column for this condition. Refer to Corporate Bulletin Number 06-02-32-002B for additional information
Filed Under (GM) by admin on 20-05-2010
2001-2002 Chevrolet Camaro 2001-2003 Chevrolet Corvette 2001-2002 Pontiac Firebird 2002-2003 Cadillac Escalade, Escalade EXT
2000-2003 Chevrolet Suburban, Tahoe 2001-2003 Chevrolet Silverado 2002-2003 Chevrolet Avalanche 2000-2003 GMC Yukon, Yukon XL 2001-2003 GMC Sierra with 4.8L, 5.3L, 5.7L or 6.0L V8 Engine (VINs V, T, Z, G, S, N, U – RPOs LR4, LM7, L59, LS1, LS6, LQ9, LQ4)
Condition Some customers may comment on an engine tick noise. The distinguishing characteristic of this condition is that it likely will have been present since new, and is typically noticed within the first 161-322 km (100-200 mi). The noise may often be diagnosed as a collapsed lifter. Additionally, the noise may be present at cold start and appear to diminish and then return as the engine warms to operating temperature. This noise is different from other noises that may begin to occur at 3219-4828 km (2000-3000 mi).
Filed Under (Chevrolet) by admin on 21-10-2010
Models: 2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission (RPOs MN3, MN7, M15, M76) Condition Some customers may comment on a 1-2 shift shudder at light to moderate acceleration. Typically, the throttle plate angle parameter is 12-20% at time of condition with vehicle speed of approximately 24-40 km/h (15-25 mph). The customer may describe the condition as slip or delayed shift into second. Correction Replace the complete second clutch assembly with service kit, P/N 24240561. Refer to the GM Unit Repair Service Manual for the year and model of the vehicle being serviced for the 2nd Clutch service procedure. This service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, other gaskets not included in this service kit will also be needed to complete the repair – a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering gasket kit 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to-Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve