2000 ford focus iac valve removal


You are searching repair manual in PDF format about 2000 ford focus iac valve removal use another keyword for search another post or files



  2000 ford focus iac valve removal Direct Download speed 5787 Kb/s

  2000 ford focus iac valve removal Full Version speed 6767 Kb/s




2001 Chevrolet Cavalier Idle Air Control Motor (IAC): Service and Repair REMOVAL PROCEDURE

0

Filed Under (Chevrolet) by admin on 16-09-2010

download
1. Remove the idle air control (IAC) valve connector. 2. Remove the IAC valve attaching screws (1). NOTE: If the IAC valve has been in service: DO NOT push or pull on the IAC valve pintle. The force required to move the pintle may damage the threads on the worm drive. Also, DO NOT soak the IAC valve in any liquid cleaner or solvent, as damage may result. 3. Remove the IAC valve assembly (2). ^ Clean the IAC valve O-ring sealing surface, the pintle valve seat, and the air passage. ^ The IAC valve may be cleaned. Use a shop towel or parts cleaning brush to remove any heavy deposits. ^ Any shiny spots on the pintle or seat are normal and do not indicate misalignment or a bent pintle shaft. ^ If the air passage have heavy deposits, remove the throttle body for a complete cleaning. ^ Inspect the IAC valve O-ring for cuts, cracks, or distortion. Replace the O-rings if necessary. ^ When installing a new IAC valve, be sure to replace the valve with an identical part. The IAC valve pintle shape and diameter are designed for a specific application. MEASUREMENT PROCEDURE This procedure is only for installing a new IAC valve. IMPORTANT: If installing a new IAC valve, replace the IAC valve with an identical part. The IAC valve pintle shape and diameter are designed for the specific application. Measure the distance between tip of the IAC valve pintle and the mounting flange. If the distance is more than 28 mm (1.1 in), use finger pressure to slowly retract the pintle. The force required to retract the pintle of a new valve will not cause damage to the valve. INSTALLATION PROCEDURE

Related entry:

mercruiser iac replacement, installation IAC muffler, 08 tacoma a/c expansion valve replacement procedure, purge valve location for 2001 pt cruiser, replacing 2001 cavalier purge solenoid valve, rsx iac relearn, servotronic solenoid, videos of Ford rangers with bad intake or exhaust valve, Where is iac valve on suzuki verona, lifter replacement 2003 chevy cavalier,

1999 Mercury Cougar Idle Air Control (IAC) Valve REMOVAL AND INSTALLATION

0

Filed Under (Mercury) by admin on 28-03-2011

download
Idle Air Control (IAC) Valve Removal 1. Disconnect the vacuum line from the exhaust gas recirculation valve. 2. Disconnect the idle air control (IAC) valve electrical connector. 3. Detach the wiring harness from the IAC valve stud. 4. Disconnect the vacuum supply lines from the upper intake manifold. 5. Remove the IAC valve. 6. Remove and discard the IAC valve gasket. Installation 1. NOTE: Install a new IAC valve gasket. To install, reverse the removal procedure.

1994-2000 Mazda 626 with 4 cyl A/T Vehicles with the Ford CD4E automatic transmission

0

Filed Under (Mazda) by admin on 10-10-2010

download
1994-1997 Ford Probe, Mazda MX3 with 4 cyl. & A/T 1994-2000 Mazda 626 with 4 cyl. & A/T 1998-2000 Mazda 626 with 6 cyl. & A/T 1995-2000 Ford Contour/Mercury Mystique with 6 cyl. & A/T 1999-2001 Mercury Cougar with A/T SUBJECT Vehicles with the Ford CD4E automatic transmission. CONDITION The driver’s side front CV axle has a 6-½ inch male inboard stub that fits into the transmission’s side gear. On the stub next to the housing seal surface is a carrier support surface that fits into the final drive sun gear inside the transmission (see figure 1). This sprocket assembly is chain driven with the reverse/overdrive sprocket by the planetary gear sets (see figure 2). The final drive sprocket assembly rides on the axle stub carrier support surface using a pressed, center bored bushing. This bushing wears the carrier support surface causing damage to the axle and eventually the transmission. SOLUTION If the carrier support surface of the axle being replaced appears rough and worn, then several possible failures need to be checked before replacing the axle or premature failure of the axle or possible damage to the transmission could occur. If the transmission’s internal oiling solenoid that lubricates this bushing fails, then the 2nd and 3rd gearshifts will not function. Although the Aftermarket lists this bushing, no tool exists to replace it. Ford only offer the bushing in a complete sprocket assembly making its replacement a very costly repair. The most common contributor to premature wear of this bushing is the vehicle not being within proper alignment specs. Without a four-wheel alignment, even though the front wheels may be centered to the rack, the rear thrust is pushing the front wheels causing stress on the front CV joints. The thrust forces acting on the front wheels while driving changes ALL the alignment specs resulting in the front wheels being in a constant turning action. This will wear the side gears and transmission seals as well as stressing this bushing. Another possible sign that alignment is affecting these items is a worn or torn inboard boot. Do not forget that worn motor mounts will also affect alignment thrust forces.

Related entry:

timing marks 2000 mazda 626 2 5 engine, mazda b 4000 manual 1994 download, yhs-adk_sychp, ford lynx gsi review, 1994 Ford L9000 Manual, what direction should turn cam to line the timing mark in a v6 1997 mazda 626, 2000 ford escort error po340 p1383, 2000 ford explorer exploded exhaust diagram, 2000 ford focus dome light assy, 2000 madza millenia 2 5 camshaft timing marks diagram,

1996 Ford Taurus valve body Removal and Installation

0

Filed Under (Ford) by admin on 16-10-2010

download
REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor. 12. Remove rear transaxle mount attaching bolt. 13. Loosen but do not remove two lefthand subframe attaching bolts. 14. Remove two engine support mount attaching bolts. 15. Remove four lefthand engine support attaching bolts, then remove the engine support. 16. Position suitable drain pan, then remove remaining transaxle side pan attaching bolts and remove pan. 17. Using suitable screwdriver, place manual shift shaft in Park position. 18. Disconnect upper bulkhead electrical connector wiring retainer clip from valve body. 19. Disconnect electrical connectors. Oil Pump And Valve Body Bolt Removal 20. Remove valve body attaching bolts, then disengage linkage and remove valve body. NOTE: Do not remove oil pump cover attaching bolts. INSTALLATION 1. Install new pump and valve body to chain cover gasket. 2. Slide pump and valve body onto pump shaft. 3. Rotate pump and valve body assembly toward dash panel, then engage manual valve link with manual valve. 4. Slightly rotate pump and valve body assembly to engage oil pump shaft splines with oil pump rotor splines. Valve body should slide flush with chain cover. A suitable 7/8 inch deep well socket on crankshaft pulley may be required for complete engagement. 5. On models less anti-skid, if engagement is not as indicated in step 4, proceed as follows: a. Remove manual valve from valve body. b. Rotate assembly to allow full engagement, up to 360° . c. After full engagement, return assembly to installed position, then install manual valve.

Related entry:

4l60e valve body bolt location, 722 3 transmission USED valve BODY, a/c without ccc carb and computer g body, 6r60 upper valve body check ball installation, ford 6r60 valve body check ball, 4L60E VALVE BODY BOLT LOCATIONS, 6R60 valve body removal, 460etransv/bboltslocation, 4hp22 transmission valve body diagram, valve body diagram for a 200r4,

1997 Ford Explorer/Mountaineer Idle Air Control (IAC) Valve REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 08-04-2011

download
Removal NOTE: 5.0L shown, 4.0L SOHC and 4.0L (push rod) similar. 1. Disconnect the idle air control (IAC) valve electrical connector. 2. Remove the IAC valve. 1. Remove the two bolts. 2. Remove the IAC valve. Discard the gasket. Installation NOTE: Install a new IAC valve gasket. 1. Install the idle air control (IAC) valve. 1. Position the IAC valve. 2. Install the two bolts. 3. Connect the IAC electrical connector.