Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

Workshop Manual & Electronic Troubleshooting Manual 2005-2006
Hyundai Accent, Elantra, Tucson, Santa Fe, Sonata, Azera, Tiberon
Table of Content

download
DESCRIPTION The following vehicles share common transaxle Diagnostic Trouble Codes (DTC): • 1996-2005 Accent • 1996-2000 Elantra • 1997-2001 Tiburon Elantra and Tiburon vehicles produced beginning 6/1/99 and 2000-2005 Accent vehicles use a valve body with six solenoids and have several new DTCs. DTC information can be found in the shop manuals, TSBs and Engine Fault Code Diagnostic Manual (OBDII Manual) listed below: DTC P0501 Vehicle speed sensor range DESCRIPTION P0703 Stop lamp switch – Open/short P0705 Range switch signal problem P0707 Range switch – open circuit P0708 Range switch – short circuit P0710 A/T fluid temperature sensor P0711 A/T temperature sensor – rational- ity check DTC P0712 A/T temperature sensor signal – open/short P0713 A/T temperature sensor signal – open/short P0717 No pulse generator A signal P0722 No pulse generator B signal P0727 Engine speed signal – open circuit DESCRIPTION P0731 1st gear incorrect ratio P0732 2nd gear incorrect ratio P0733 3rd gear incorrect ratio P0734 4th gear incorrect ratio P0740 Torque converter clutch control system problem P0741 Damper clutch stuck off P0742 Damper clutch stuck on P0743 Damper clutch control solenoid valve – open/short P0745 Pressure control solenoid valve A – open/short, TR-9 P0747 Pressure control solenoid valve – open P0748 Pressure control solenoid valve – short P0750 Shift control solenoid valve A – open/short P0752 Shift control solenoid valve A – open P0753 Shift control solenoid valve A – short P0755 Shift control solenoid valve B – open/short P0757 Shift control solenoid valve B – open P0758 Shift control solenoid valve B – short

download
1999-2000 SONATA SHUDDER OR VIBRATION DURING ACCELERATION DESCRIPTION: Some 1999-2000 Sonata vehicles produced prior to 4/12/00 may shudder or vibrate slightly during medium to full throttle acceleration. To correct this condition, replace both CV joints on the left and right side driveshafts. REPAIR INFORMATION: 1. Remove the drive shaft according to the 1999 or 2000 Sonata Shop Manual, Page DS- 8. Assemble the new driveshaft as shown in Steps 2-6. 2. Install the small band and boot on the joint and shaft kit. 3. Install the spider and the C-clip. 4. Add CV grease (supplied with the joint and shaft kit) to the case and boot. 5. Install the case to the spider. 6. Install the boot to the case and attach both bands on the boot, using CV joint pliers. NOTE :Use Snap-On YA3050 and YA3OBO or Blue-Point TA3050 and TA3080 or equivalent. 7. Install the axle shaft to the vehicle. 8. Test drive the vehicle and check for vibration.

download
While installing the tube and hose assembly, be sure to align white marks on each fitting. Pressure Hose and Tube 1. Remove the air intake hose assembly. 2. Detach the pressure hose mounting clamp. 3. Disconnect the pressure tube fitting at the gear box side. 2000 Hyundai Elantra GLS Wagon L4-2.0L 4. Lift up the vehicle and detach the mounting clamp which is holding both the pressure tube and the return tube. 5. Lift down the vehicle and remove the connector (24 mm). 6. Remove the pressure hose and tube assembly. 7. Installation is the reverse order of removal. NOTE: 1. Install the pressure hose and tube so that they are not twisted and they do not come in contact with any other parts. 2. After installation, bleed the system. Return Tube and Hose 1. Detach the power steering fluid reservoir from its mounting bracket. 2. Remove the engine coolant reservoir. 2000 Hyundai Elantra GLS Wagon L4-2.0L 3. Detach the return tube and hose assembly mounting clamps. 4. Remove the air intake hose assembly. 5. Disconnect the pressure tube and the return tube fittings at the gear box side. 6. Lift up the vehicle and detach the mounting clamp which is holding both the pressure tube and the return tube. 7. Lift down the vehicle and disconnect the clamp holding the return tube & hose assembly (G) and (C). 2000 Hyundai Elantra GLS Wagon L4-2.0L 8. Remove the return tube & hose assembly (G). 9. Detach the air conditioning discharge hose mounting clamp. 10. Disconnect the clamp holding the return tube & hose assembly (C) and the oil cooler tube. 11. Remove the return tube & hose assembly (C). 12. Installation is the reverse order of removal. NOTE: 1. Install the return tube and hose assembly so that it is not twisted and it does not come in contact with any other parts. 2. After installation, bleed the system. Oil Cooler Tube 1. Remove the front bumper and rail assembly. (Refer to Body and Frame.) 2. Disconnect the connection of the oil cooler tube from the return tube. 3. Disconnect the connection of the coil cooler tube from the return hose of the fluid reservoir.

download
NOTE: Both pulse generator-B inspection and TCM reprogramming procedures should be performed. PULSE GENERATOR-B INSPECTION PROCEDURE: 1. Open and secure the hood. 2. Remove the resonator. 3. Locate the pulse generator under the battery tray. Disconnect the pulse generator connector (blue) and remove the pulse generator male connector (black) from the bracket. 2001 Hyundai Accent GS Sedan L4-1.6L 4. Using an ohmmeter, check the resistance between terminal No. 3 and No. 4 in the disconnected pulse generator male connector (black color). Resistance value: 215-275W (at 20°C or 68°F) If the resistance is lower or higher than the specification, replace the pulse generator (P/N 45955-22700). If the resistance is within specification go to Step 5. 5. Clean both ends of the disconnected pulse generator connectors with aerosol electrical contact cleaner. 6. Apply contact grease (P/N 00305-F0000-39, NYOGEL 760G), into all four terminal openings of the blue female connector until each terminal opening is completely filled with grease. 7. Reconnect the pulse generator connectors and reattach the connector to the bracket. Reinstall all removed components in the reverse order of removal. TCM SPECIFICATIONS CAUTIONS BEFORE REPROGRAMMING: