Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
IMPORTANT: The important statement at the beginning of the “Ignition Lock Cylinder removal procedure on page 188 in the 2000/2001 Saturn S-Series Body/Electrical Volume II Service Manual is incorrect. Please cross out the important on that page and write in the following important statement. IMPORTANT: When replacing the ignition lock cylinder only, the passlock relearn procedure is not required. 1. Disconnect negative battery cable. 2. Remove lock cylinder bezel from steering column shroud by carefully prying with a thin bladed screwdriver. 3. Remove shroud fasteners and remove steering column upper and lower shroud panels. 4. Insert key into ignition lock cylinder and rotate to RUN position. If ignition lock cylinder can be rotated to RUN position, continue to step 30. ^ If ignition lock cylinder cannot be rotated to RUN position, continue with next step.

download
2000-2001 I30 AND 2002 I35; DRIVER’S SEAT WILL NOT MOVE FORWARD OR BACKWARD This bulletin amends ITB00-067. This version includes additional Model and Model Year application. Please discard all paper copies of the earlier bulletin. If the driver’s seat in an applied vehicle will not move in the forward or backward direction, the seat slide motor and gear assembly may need replacement (see figure 1). If this should occur, follow the Service Procedure in this bulletin to assist in diagnosing the incident and, if necessary, install the Seat Slide Motor kit (see the Parts Information section of this bulletin). NOTE: This is the ONLY approved repair procedure for this incident. A claim to Infiniti division for the repair of this incident may be denied if the repair is not performed exactly as outlined in this bulletin.

download
Some 2000-2009 Focus vehicles may exhibit an excessive engine vibration at idle, most noticeable when the transmission is engaged in reverse. This condition may be caused by small stones, road debris, ice or snow packed / lodged in the rear engine roll restrictor. ACTION: Inspect the rear engine roll restrictor for debris and install service shield if necessary. SERVICE PROCEDURE 1. 2. 3. 4. 5. Inspect the rear engine roll restrictor for debris. Remove any debris from rear engine roll restrictor. Remove the cross member-to-roll restrictor attachment bolt. Install service shield. (Figure 1) Install roll restrictor attachment bolt and torque to 35 lb-ft (47 N-m).

download
DESCRIPTION The following vehicles share common transaxle Diagnostic Trouble Codes (DTC): • 1996-2005 Accent • 1996-2000 Elantra • 1997-2001 Tiburon Elantra and Tiburon vehicles produced beginning 6/1/99 and 2000-2005 Accent vehicles use a valve body with six solenoids and have several new DTCs. DTC information can be found in the shop manuals, TSBs and Engine Fault Code Diagnostic Manual (OBDII Manual) listed below: DTC P0501 Vehicle speed sensor range DESCRIPTION P0703 Stop lamp switch – Open/short P0705 Range switch signal problem P0707 Range switch – open circuit P0708 Range switch – short circuit P0710 A/T fluid temperature sensor P0711 A/T temperature sensor – rational- ity check DTC P0712 A/T temperature sensor signal – open/short P0713 A/T temperature sensor signal – open/short P0717 No pulse generator A signal P0722 No pulse generator B signal P0727 Engine speed signal – open circuit DESCRIPTION P0731 1st gear incorrect ratio P0732 2nd gear incorrect ratio P0733 3rd gear incorrect ratio P0734 4th gear incorrect ratio P0740 Torque converter clutch control system problem P0741 Damper clutch stuck off P0742 Damper clutch stuck on P0743 Damper clutch control solenoid valve – open/short P0745 Pressure control solenoid valve A – open/short, TR-9 P0747 Pressure control solenoid valve – open P0748 Pressure control solenoid valve – short P0750 Shift control solenoid valve A – open/short P0752 Shift control solenoid valve A – open P0753 Shift control solenoid valve A – short P0755 Shift control solenoid valve B – open/short P0757 Shift control solenoid valve B – open P0758 Shift control solenoid valve B – short

download
All Vehicles 1. CAUTION: The maximum amount by which the engine management system will adjust the camshaft timing (VCT control unit) is limited to two degrees. As a result of this an extremely high degree of accuracy is required for any work which affects the valve timing. NOTE: The locations of engine mountings and engine support insulators are described looking from the transaxle to the engine. NOTE: Operation steps which only apply to certain model variants and therefore do not apply to all vehicles are clearly marked. Disconnect the battery ground cable. 2. Raise and support the vehicle. For additional information, refer to Section 100-02. 3. Loosen the right-hand front wheel nuts. 4. Remove the right-hand front wheel. 5. Remove the engine underschield (if equipped). 6. Remove the right-hand front splash shield. 7. NOTE: Mark the accessory drive belt direction if the belt is to be reused. Remove the accessory drive belt. 1. Loosen the water pump pulley bolts. 2. Working clockwise, loosen the belt and remove it. ? Remove the water pump pulley. 4. Remove the belt idler pulley. 8. NOTE: Using the access hole in the bottom of transaxle case to stop rotation of engine. Remove the crankshaft pulley/vibration damper. CAUTION: The removal of the lower part of the engine front cover is necessary to avoid damage to the timing belt. Remove the lower part of the engine front cover. Vehicles with manual transaxle 10. Loosen the center bolt of the right-hand engine support insulator two turns. Vehicles with automatic transaxle 11. Loosen the center bolt of the right-hand engine support insulator two turns. All Vehicles  2000 Contour/Mystique Workshop Manual 12. Loosen the center bolt of the left-hand engine support insulator two turns. 13. Lower the vehicle. 14. Detach the coolant expansion tank and position it to one side. ? Disconnect the speed control cable (if equipped) from the coolant expansion tank.