2000 subaru outback bumper removal


You are searching repair manual in PDF format about 2000 subaru outback bumper removal use another keyword for search another post or files



  2000 subaru outback bumper removal Direct Download speed 5787 Kb/s

  2000 subaru outback bumper removal Full Version speed 6767 Kb/s




1996 Ford Mustang Bumper and Bumper Cover Front Removal and Installation

0

Filed Under (Ford) by admin on 16-02-2011

download
1. Drill out four license plate rivets (if required). 2. Remove fog lamps (15200) (if equipped). 3. Remove two nuts and two screws retaining front bumper (17757) to each front fender (16005). 4. Remove one screw (3 on Cobra) retaining front bumper cover (17D957) to each front fender splash shield (16102). 5. Remove three pushpins retaining front bumper cover to radiator support (16138). 6. Remove two upper blind rivets retaining front bumper cover to radiator grille opening panel reinforcement (8A284). Front Bumper Cover 7. Remove two rivets retaining front bumper cover support (17C947) to front bumper. Remove center pins from rivets using a drift punch. Remove the remainder of the rivets using a drill. Use care not to enlarge the retaining holes in the sheet metal. 8. Remove LH and RH headlamp bulbs (13007). Refer to Section 17-01. 9. Insert a thin screwdriver blade between the underside of the front bumper cover and the radiator grille opening panel reinforcement to release the front bumper cover locking tabs on both LH and RH sides, underneath the headlamp opening. Remove the front bumper cover while the lock tabs are lifted. Front Bumper Cover Removal 11. On each side of vehicle (convertible only), remove one bolt and one nut retaining front bumper vibration damper to front bumper. Front Bumper Vibration Damper—Convertible

Related entry:

remove bumper from es 300 lexus 2003, r129 front bumper removal, google es 300 lexus remove bumper 2003, how to remove bumper cover on 2007 aveo, 2007 camary toyota front bumper cover removal, 2006 FORD EXPLORER Bumper Cover Retainer, how to remove front bumber toyota yaris 2003, how to remove wheel arch cover honda crv, how to remove bumper on 206, pictures of a removed fender on toyota yaris 2007,

TOYOTA FJ CRUISER – FRONT BUMPER INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota) by admin on 15-01-2011

download
Front Bumper Installation – TOYOTA FJ CRUISER Step 1 Very Important Before beginning installation, assure that vehicle has been pulled forward into work-area with the wheels straight and that the ground is level. The clearances around the FJ bumper are critical to proper installation and fitment. Moving vehicle with wheels turned causes slight frame twist preventing ease of removal of OE bumper and installation of new bumper without issue. Make sure you have plenty of room to work around front of vehicle. Open the hood at this time, you will need to see down through the inner-body core-support while removing your OE bumper and installing your Body Armor FJ Bumper. Step 2 a. Unpack bumper using staple puller to remove staples. Save all packing materials and take care not to tear cartons. b. Remove hardware and misc.parts. Check parts/hardware list to confirm all parts and necessary hardware are included. c. It’s a good idea to spray all OE attaching hardware at this time with penetrating oil before beginning removal of OE bumper. This will ease removal as well as to help assure that none of the bolts’ / nuts’ threads are damaged during removal. Use extra caution when working with the bumper mounting studs & nuts. Step 3 a. Begin removing OE bumper following instructions and photos on the following page for detailed descriptions and references. When done, proceed to Step 4 here. Step 4 a. If equipped, remove OE chassis skid plate and set aside for install after new bumper is installed. Save OE hardware to re-install the skid plate once new bumper is installed (3 upper bolts and 2 lower bolts, lowers have spacers between frame & skid plate). b. Remove the (3) outer hold-down hex nuts holding bumper to frame-caps on both passenger and driver sides. Un-clip the outer ends of the bumper from the outer bumper support clips (see Photo 5 on following page) by pulling bumper fascia down and out of clip on driver and passenger sides. Next, while a helper holds the bumper in place, loosen and remove the inner hold-down hex nuts on both passenger and driver sides. Reference Photo 1 on the last page for stud locations. The bumper should now slide off the front of the locating / mounting studs in the frame-caps. Remove slowly prevent paint damage. Save hold-down nuts. c. Remove the outer bumper support clips from both driver and passenger sides (see Photo 5 on following page) Step 5

Related entry:

2001 tahoe front bumper removal, renault clio bumper removal, remove rear S320 bumper, remove 2001 volvo xc70 front splash shield remove, mk8 Fiesta front bumper removal, how to replace fj corner bumper, how to remove the bumper 2001 vw jetta, entervan cladding, 2001 volvo xc70 front splash shield remove, windstar front bumper removal,

2003 Mazda 6 FRONT BUMPER REMOVAL/INSTALLATION

0

Filed Under (Mazda) by admin on 08-11-2010

download
1. Disconnect the negative battery cable. 2. Disconnect the front side maker light connector. 3. Remove in the order indicated in the table. 4. Install in the reverse order of removal. Front Bumper Removal Note 1. Pull the front bumper ends (wheel arch) outward to disengage from the bumper slider. CAUTION: If only one side of the front bumper is disengaged from the bumper slider and the bumper falls, it could be damaged. When disengaging the front bumper from the slider, secure the bumper so that it does not fall. 2. Remove the front bumper from the body. Front Bumper Installation Note 1. Spread the front bumper ends (wheel arches) apart. 2. Attach the front bumper to the body. 3. Press the front bumper connecting area into the body to engage with the bumper slider.

Related entry:

how to remove 2001 mazda 626 front bumper,

2003 Subaru Outback REAR WIPER ARM REMOVAL

0

Filed Under (Subaru) by admin on 25-04-2010

download
1. Raise wiper arm cover (A). 2. Loosen nut to remove wiper arm. Fig. 29: Raising Wiper Arm Cover Courtesy of SUBARU OF AMERICA, INC. INSTALLATION 1. Install in the reverse order of 2. Operate rear wiper 3. Align blade to rear defogger heat wire (A). REAR WIPER MOTOR 1. Remove rear wiper arm. 2. Remove cap (A), nut (B), and spacer (C) from rear wiper shaft.

Related entry:

Replace rear wiper arm outback, schematic sun visor backup camera system subaru outback, 1986 subaru gl repair manual, 2010 subaru outback lift gate door interior panel, 2010-2014 subaru outback lift gate diagram,

2007 Honda Element Front Bumper Removal/Installation

0

Filed Under (Honda) by admin on 07-07-2010

download
Front Bumper Removal/Installation NOTE: Have an assistant help you when removing and installing the front bumper. Take care not to scratch the front bumper and body. Put on gloves to protect your hands. 1. Remove the front grille cover. 2. Remove the bolts (A), screws (B, C), and clips (D) securing the front bumper. 3. Pull on the front bumper (A) at the wheel arch areas to release it from the hooks (B) on the side spacers (C) and front fender cladding (D). 4. SC model: With the help of an assistant, while pulling the wheel arch portion away from the front fender cladding (A), pull out on the front bumper (B) to release the bumper from the hooks (C) on the center upper beam (D). Remove the front bumper. 5. LX, EX models: With the help of an assistant, while pulling the wheel arch portion away from the front fender cladding (A), pull out on the front bumper (B) and remove it. 6. Install the bumper in the reverse order of removal, and note these items: Make sure the front bumper engages the hooks (of both corner upper beams (SC model), front fender claddings and side spacers) on each side securely. Push the clips and hooks into place securely. Check if the clips are damaged or stress-whitened, and if necessary, replace them with new ones.

Related entry:

front bumper removal Honda Element, honda civic 2007 bumper grill removal,