2001 chevy malibu 3.1 liter
You are searching repair manual in PDF format about 2001 chevy malibu 3.1 liter use another keyword for search another post or files
2001 chevy malibu 3.1 liter Direct Download speed 5787 Kb/s
2001 chevy malibu 3.1 liter Full Version speed 6767 Kb/s
Filed Under (Ford) by admin on 27-04-2010
ISSUE Some 2001-2005 Taurus/Sable, 2001-2006 Escape and 2005-2006 Mariner vehicles built prior to
1-17-2006 equipped with the 3.0L 4V Duratec engine may exhibit a ticking noise from the left bank cylinder head, with the engine at normal operating temperature only.
ACTION To diagnose, with the engine running and warm (normal operation temperature), using a mechanic’s stethoscope determine if the ticking noise is coming from the left hand intake camshaft at cylinder number 6, (Figure 1). If the ticking noise can be verified, refer to the following Service Procedure.
Filed Under (Chevrolet) by admin on 21-10-2010
Models: 2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission (RPOs MN3, MN7, M15, M76) Condition Some customers may comment on a 1-2 shift shudder at light to moderate acceleration. Typically, the throttle plate angle parameter is 12-20% at time of condition with vehicle speed of approximately 24-40 km/h (15-25 mph). The customer may describe the condition as slip or delayed shift into second. Correction Replace the complete second clutch assembly with service kit, P/N 24240561. Refer to the GM Unit Repair Service Manual for the year and model of the vehicle being serviced for the 2nd Clutch service procedure. This service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, other gaskets not included in this service kit will also be needed to complete the repair – a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering gasket kit 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to-Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve
Filed Under (Chevrolet) by admin on 21-01-2011
Subject: Clunk, Knock or Rattle Noise From Front of Vehicle While Driving or Turning Over Bumps at Low Speeds (Diagnose Noise and Perform Outlined Repair) Models: 2004-2006 Chevrolet Malibu Maxx 2004-2008 Chevrolet Malibu Classic 2008-2010 Chevrolet Malibu 2005-2010 Pontiac G6 2007-2010 Saturn Aura Supercede: This bulletin is being revised to update the models years and revise the information for Correction 2. Please discard Corporate Bulletin Number 06-02-32-007E (Section 02 – Steering). Condition 1 Some customers may comment on a clunk noise heard and felt in the steering wheel while driving at slow speeds and turning. The clunk noise may appear to be directly in front of the driver. Hitting a bump while turning can produce the clunk noise. Sometimes the noise may be duplicated when the vehicle is sitting still and the steering wheel is turned 90 degrees in either direction before initially centering the steering wheel. Cause 1 The clunk noise may be caused by a slip/stick condition between the inner and outer components of the intermediate shaft. Important Revised design intermediate shafts went into production in the 2009 model year and are the only design currently available through GMSPO since approximately September 2008. Since any model year vehicle could have had a second design shaft installed, it is critical to identify it before proceeding. The revised design intermediate shafts will NOT tolerate any type of lubricant per the following instructions. Adding lube to the second design shafts will cause a clunk noise in a very short period of time. Use the following pictures to identify which design of shaft you are servicing. Electric Assist Power Steering
Filed Under (Buick) by admin on 14-11-2010
Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville steering vibration, shudder or moan noise when steering during parking maneuvers on dry pavement. Correction Install a new power steering pressure (inlet) hose assembly on the following vehicles: • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra Install a new power steering pressure (inlet) and return (outlet) hose assembly on the following vehicles: • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville 1. Verify that the power steering pump reservoir is full. • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. Verify proper belt tension and operation of the belt tensioner. Check for power steering hose ground out conditions. Check for good engine idle and correct engine RPM. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used 2. 3. 4. 5. 6.
Filed Under (Ford) by admin on 27-01-2011
ISSUE Some 2001-2005 Escape vehicles equipped with a 3.0L engine may exhibit idle speeds outside the specified range. Some 2001-2003 Escape vehicles equipped with a 3.0L engine and CD4E automatic transaxle may exhibit a transmission shudder. ACTION Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE 1. If the concern is a 2001-2005 Escape with idle speeds outside the specified range: a. Install a new idle air control (IAC) valve with jumper harness included in the kit. The new Denso brand IAC will be installed with the electrical connector facing the opposite direction of the original (Hitachi) valve which is why the jumper harness is required. The original (Hitachi) IAC connector faces the front of the vehicle while the new Denso IAC connector faces toward the rear of the vehicle. b. Referring to the calibration charts (Figures 1 and 2), select the applicable file and reprogram the powertrain control module (PCM) using the TSB Service Procedure and WDS/IDS release B40.5 and higher. Calibration files may also be obtained at www.motorcraft.com. 2. If the concern is a 2001 – 2003 Escape with transaxle shudder, drain, flush and refill the transmission fluid with MERCON® Multi-Purpose Automatic Transmission Fluid. Then, referring to the calibration charts (Figures 1 and 2), select the applicable file and reprogram the PCM using the TSB Service Procedure and WDS/IDS release B40.5 and higher. Calibration files may also be obtained at www.motorcraft.com. 3. When reprogramming the PCM use blank path programming. Select the proper file from the chart and manually enter the PCM part number or tear tag number to obtain the updated calibration file. If the concern is a 2001-2005 Escape with idle speeds outside the specified range: a. Install a new idle air control (IAC) valve with