2001 kia sportage 4 wheel drive vacuum diagrams
You are searching repair manual in PDF format about 2001 kia sportage 4 wheel drive vacuum diagrams use another keyword for search another post or files
2001 kia sportage 4 wheel drive vacuum diagrams Direct Download speed 5787 Kb/s
2001 kia sportage 4 wheel drive vacuum diagrams Full Version speed 6767 Kb/s
Filed Under (Jeep) by admin on 18-11-2010
1. Disconnect vacuum hose at speed control servo and install a vacuum gauge into the disconnected hose. 2. Start engine and observe gauge at idle. Vacuum gauge should read at least ten inches of mercury. 3. If vacuum is less than ten inches of mercury, determine source of leak. Check vacuum line to engine for leaks. Also check actual engine intake manifold vacuum. If manifold vacuum does not meet this requirement, check for poor engine performance and repair as necessary. 4. If vacuum line to engine is not leaking, check for leak at vacuum reservoir. To locate and gain access to reservoir, refer to Vacuum Reservoir REMOVAL /INSTALLATION . Disconnect vacuum line at reservoir and connect a hand-operated vacuum pump to reservoir fitting. Apply vacuum. Reservoir vacuum should not bleed off. If vacuum is being lost, replace reservoir. 5. Verify operation of one-way check valve and check it for leaks. a. Locate one-way check valve. The valve is located in vacuum line between vacuum reservoir and engine vacuum source. Disconnect vacuum hoses (lines) at each end of valve. b. Connect a hand-operated vacuum pump to reservoir end of check valve. Apply vacuum. Vacuum should not bleed off. If vacuum is being lost, replace one-way check valve. c. Connect a hand-operated vacuum pump to vacuum source end of check valve. Apply vacuum. Vacuum should flow through valve. If vacuum is not flowing, replace one-way check valve. Seal the fitting at opposite end of valve with a finger and apply vacuum. If vacuum will not hold, diaphragm within check valve has ruptured. Replace valve.
Related entry: 03 dodge caravan vacuum control
, 2007 FORD CROWN VICTORIA H V A C VACUUM SCHEMATIC
, 2004 vacuum line chevy avalanche
, 1989 honda accord lx vacuum hose routing guide
, ford2003taurus vacume hose detached under car
, how do you check for air leaks on 1998 Isuzu Rodeo?
, vacuum tubing for a/c on 1998 dodge dakota
, 1980 corvette vacuum hose diagram
, VW Vacuum Pump Diagnostic
, 1999 oldsmobile aurora vacum diagram
Filed Under (Lincoln) by admin on 11-01-2011
Removal & Installation WARNING Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied. NOTE Have an assistant press the brake pedal to keep the axle from turning. 1. Before servicing the vehicle, please familiarize yourself with safety procedures. ? Remove the axle-to-wheel hub retainer nut and washer. ? Remove the parking brake shoes. WARNING Do not use a hammer to separate the outboard CV-joint from the hub. Damage to the threads and internal CV-joint components can result. 2. 3. ? Press the outboard CV-joint until it is loose from the hub. ? Remove and discard the toe link-to-wheel knuckle nut. WARNING Do not damage the boot while separating the toe link from the wheel knuckle. 4. 5. ? Remove the bolt and separate the toe link from the wheel knuckle. ? Remove and discard the upper arm-to-wheel knuckle nut. WARNING Do not damage the boot while separating the ball joint from the wheel knuckle. 6. 7. ? Remove the bolt and separate the upper arm from the wheel knuckle. ? Remove and discard the lower arm-to-wheel knuckle nut. 8. 9. ? Remove the lower arm-to-wheel knuckle bolt. ? Remove the wheel knuckle. ? Using a suitable press, remove and discard the wheel hub. ? Remove and discard the wheel bearing retainer ring. ? Using a suitable press, remove the wheel bearing. 10. 11. 12. 13. 14. Fig. Rear hub/bearing Assembly-Aviator, Explorer and Mountaineer Fig. Pressing out the bearing ? To install: 1. Installation is the reverse of the removal procedure. ? Observe the following torques: 2. Lower arm-to-wheel knuckle nut: 111 ft. lbs. (150 Nm). ? Upper arm-to-wheel knuckle nut: 66 ft. lbs. (90 Nm). ? Toe link-to-wheel knuckle nut: 66 ft. lbs. (90 Nm). ? Axle-to-hub retainer nut: 203 ft. lbs. (275 Nm). ? ? Always install a new: 3. Axle-to-wheel hub retainer nut. ? Toe link-to-wheel knuckle nut. ? Upper arm-to-wheel knuckle nut. ? Lower arm-to-wheel knuckle nut. ? Wheel hub. ? Wheel bearing retainer ring. ? ? 1. Before servicing the vehicle, refer to the precautions in the beginning of this section. ? Remove or disconnect the following: NOTE Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied. 2. NOTE Do not use a hammer to separate the outboard CV joint from the hub. Damage to the threads and internal CV joint components may result.
Related entry: 2001 dodge dakota torque measurements wheel bearing
, 1998 ford ranger front axle bearing diagram
, 2003 envoy front hub torque
, 2005 lexus rx330 torque specs front axle
, PONTIAC MONTANA 2007 TORQUELACK NUT
, nissan serena spare tyre
, 2002 4 x 4 blazer hub assembly torq specs
, braun m/n 7684la wire diagram
, super duty wheel hub vacum actuators
, braun 7684la
Filed Under (Dodge) by admin on 17-06-2010
1992 ENGINE PERFORMANCE Chrysler Motors/Mitsubishi Vacuum Diagrams Chrysler Motors; Colt, Colt 200, Colt Vista, Ram-50, Stealth, Summit, Summit Wagon Mitsubishi; Diamante, Eclipse, Expo/Expo LRV, Galant, Mirage, Montero, Pickup, Precis, 3000GT INTRODUCTION This article contains underhood views or schematics of vacuum hose routing. Use these vacuum diagrams during the visual inspection in F – BASIC TESTING article in the ENGINE PERFORMANCE Section. This will assist in identifying improperly routed vacuum hoses, which cause driveability and/or computer-indicated malfunctions. VACUUM DIAGRAMS COLT, COLT 200, MIRAGE & SUMMIT Fig. 1: Vacuum Diagram (Colt, Colt 200, Mirage 1.5L & Summit Calif.)
Related entry: 92 plymouth colt not picking up speed?
Filed Under (Ford) by admin on 02-02-2011
The recommended wheel bearing lubricant is lithium-base High-Temperature Constant Velocity Joint Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. CAUTION: Sodium-base grease is not compatible with lithium-base grease. Do not intermix. Clean all old lubricant grease prior to lubricating front/rear wheel bearing. Use of incompatible bearing lubricant could result in premature lubricant breakdown. NOTE: If bearing adjustment does not eliminate looseness or rough and noisy operation, clean, inspect and repack the hub and wheel bearings with specified wheel grease. If wheel bearing cup or the cone and roller assemblies are worn or damaged, they should be replaced. Manual Locking Hub, Ranger Disassembly 1. Raise the vehicle and install Rotunda Car/Truck Stands 077-00018 or equivalent. 2. Remove the wheel and tire assembly. 3. Remove the retainer washers and remove the hub assembly. Refer to Manual Locking or Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for removal. 4. Remove the disc brake caliper (2B120) as described in Section 06-03. 5. Remove the hub and rotor. Remove the outer wheel bearing cone. 6. Remove the wheel hub grease seal (1190) from the rotor with Seal Remover TOOL-1175-AC or equivalent and Impact Slide Hammer T50T-100-A. Discard wheel hub grease seal and replace upon assembly. 7. Remove excluder seal. 8. Remove the inner wheel bearing. 9. NOTE: If new wheel bearing cups are installed, install new cone and roller assemblies. Inspect the wheel bearing cups for pits or cracks. If necessary, remove them with Internal Puller D80L-943-A or equivalent and Impact Slide Hammer T50T-100- A. Assembly 1. Lubricate the wheel bearings with High Temperature Constant Velocity Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. Clean all grease from the hub. Pack the cones and rollers. If a bearing packer is not available, work as much lubricant as possible between the rollers and the cages. 2. If wheel bearing cups are to be installed, position wheel bearing cups in rotor and drive in place with Bearing Cup Replacer T80T-4000-P and Driver Handle T80T-4000-W. 3. Position excluder seal on spindle and drive into position using Spindle Seal Replacer T95T-3132-D. 4. Position the inner wheel bearing in the inner wheel bearing cup in the rotor. Install the wheel hub grease seal by driving in place with Seal Replacer T80T-4000-T and Driver Handle T80T-4000-W. 5. Carefully install the rotor onto the front wheel spindle (3105). Refer to Section 06-03. 6. Install outer wheel bearing into rotor. 7. Refer to Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for remainder of installation.
Related entry: 1991 ford explorer installed front wheel spindle bearing?
, 1991 front wheel bearing 4x4 keeps comming loose isuzu trooper
, 1993 EXPLORER FRONT ROTOR SPECS
, 2006 ford ranger front hub assembly 4x4 diagram
, 2006 Ford Ranger Rear wheel bearing diagram
, esploded diagram of a 1995 tacoma 4wd front bearing
, how to instol an isuzu trooper front well bearing
, stuck wheel hub assembly sivlerado
Filed Under (Toyota) by admin on 14-06-2010
ARTICLE BEGINNING 1991 ENGINE PERFORMANCE Vacuum Diagrams Camry, Celica, Corolla, Cressida, Land Cruiser, MR2, Pickup, Previa, Supra, Tercel, 4Runner INTRODUCTION This article contains underhood views or schematics of vacuum hose routing. Use these vacuum diagrams during the visual inspection in F – BASIC TESTING. This will assist in identifying improperly routed vacuum hoses which cause driveability and/or computer-indicated malfunctions. CAMRY VACUUM DIAGRAMS