2001 ranger climate control vacuum line diagram


You are searching repair manual in PDF format about 2001 ranger climate control vacuum line diagram use another keyword for search another post or files



  2001 ranger climate control vacuum line diagram Direct Download speed 5787 Kb/s

  2001 ranger climate control vacuum line diagram Full Version speed 6767 Kb/s




1999 Ford Expedition Climate Control System DIAGNOSIS AND TESTING

0

Filed Under (Ford) by admin on 28-03-2011

download
Inspection and Verification 1. Verify the customer’s concern by operating the climate control system to duplicate the condition. 2. Inspect to determine if one of the following mechanical or electrical concerns apply: Visual Inspection Chart Loose, missing or damaged A/C compressor drive belt. Loose or disconnected A/C clutch. Loose, misrouted or damaged vacuum lines. Broken or leaking vacuum control motora Discharged A/C system. Broken or leaking refrigerant lines. a a A leak in the vacuum control circuit may occur during acceleration (slow leak), may exist at all times (large leak), and may exist only when specific functions are selected (indicating a leak in that portion of the circuit). The vacuum hoses used in the passenger compartment control circuit are constructed from PVC plastic material. The vacuum hoses used in the engine compartment are constructed of Hytrel®. Because of the materials used, never pinch the vacuum hoses off during diagnosis to locate a leak. A wood golf tee can be used as a plug when it is necessary to plug one end of the vacuum hose for leak test purposes. 3. If the inspection reveals obvious concern(s) that can be readily identified, service as required. 4. If equipped with the electronic automatic temperature control system, go to Step 6. 5. If equipped with a manual A/C system, determine the symptom and go to the Symptom Chart. 6. If the concern remains after the inspection, connect the Rotunda New Generation Star (NGS) Tester to the data link connector (DLC) located beneath the instrument panel to carry out the DATA LINK DIAGNOSTICS test. If the NGS responds with NO RESPONSE/NOT EQUIPPED for the electronic automatic temperature control module, GO to Pinpoint Test A. If the DATA LINK DIAGNOSTICS test is passed for the electronic automatic temperature control module, retrieve the continuous DTCs and execute the Self-Test Diagnostics for the electronic automatic temperature control module to retrieve the current DTCs. Mechanical Electrical Open fuses. Blower motor inoperative. A/C compressor inoperative. Circuitry open/shorted. Disconnected electrical connectors. 7. If the self-test is passed and no DTCs are retrieved, go to the Symptom Chart to continue diagnostics. 8. If DTCs are retrieved, go to the Electronic Automatic Temperature Control (EATC) Module Diagnostic Trouble Code (DTC) Index to continue diagnostics. 9. If the electronic automatic temperature control module cannot be accessed by the NGS, GO to Pinpoint Test A. Electronic Automatic Temperature Control Module Self-Test The EATC module self-test will not detect concerns associated with data link messages like engine coolant temperature or vehicle speed signals. A NGS tester must be used to retrieve these concerns. The EATC module self-test will detect concerns in the system control functions and will display hard diagnostic trouble codes (DTCs) in addition to intermittent diagnostic trouble codes for concerns that occur during system operation. The vehicle interior temperature should be between 4-32° (40-90°F) when performing the self-test. If the temperatures are C not within the specified ranges, false in-car temperature sensor DTCs will be displayed. The self-test can be initiated at any time. Normal operation of the system stops when the self-test is activated. To enter the self-test, press the OFF and FLOOR buttons simultaneously and then press the AUTOMATIC button within two seconds. The display will show a pulse tracer going around the center of the display window. The test may run as long as 30 seconds. Record all DTCs displayed. If any DTCs appear during the self-test, follow the diagnostics procedure given under ACTION for each DTC given. If a condition exists but no DTCs appear during the self-test, refer to the Symptom Chart Condition: The EATC System Is Inoperative, Intermittent or Improper Operation. To exit self-test and retain all intermittent DTCs, push the blue (cooler temperature) button. The control will exit self-test, retain all intermittent DTCs and then turn OFF (display blank). To exit self-test and clear all DTCs, press the DEFROST button. The vacuum fluorescent display window will show 888 and all function symbols for one second. Then, the EATC control assembly will turn OFF (display blank) and all DTCs will be cleared. Always exit the self-test before powering the system down (system turned OFF). Intermittent DTCs will be deleted after 80 ignition switch ON cycles after the intermittent condition occurs.

Related entry:

2006 hyundia azera passenger blend door actuator location, how to remove hj60 edic control arm, how to replace heater climate control montana, how do you remove the climate control panel on a 2006 rav4, audi a4 automatic climate control reset, ford expedition climate control codes, 2009 nissan versa climate control, CLIMATE CONTROL REMOVAL ON 2008 KIA SORENTO, REPLACING TEMP CONTROL IN 2007 IMPALA, vw lt35 glow plug relay test,

2004 Jeep Grand Cherokee Limited DIAGNOSIS AND TESTING – VACUUM RESERVOIR

0

Filed Under (Jeep) by admin on 18-11-2010

download
1. Disconnect vacuum hose at speed control servo and install a vacuum gauge into the disconnected hose. 2. Start engine and observe gauge at idle. Vacuum gauge should read at least ten inches of mercury. 3. If vacuum is less than ten inches of mercury, determine source of leak. Check vacuum line to engine for leaks. Also check actual engine intake manifold vacuum. If manifold vacuum does not meet this requirement, check for poor engine performance and repair as necessary. 4. If vacuum line to engine is not leaking, check for leak at vacuum reservoir. To locate and gain access to reservoir, refer to Vacuum Reservoir REMOVAL /INSTALLATION . Disconnect vacuum line at reservoir and connect a hand-operated vacuum pump to reservoir fitting. Apply vacuum. Reservoir vacuum should not bleed off. If vacuum is being lost, replace reservoir. 5. Verify operation of one-way check valve and check it for leaks. a. Locate one-way check valve. The valve is located in vacuum line between vacuum reservoir and engine vacuum source. Disconnect vacuum hoses (lines) at each end of valve. b. Connect a hand-operated vacuum pump to reservoir end of check valve. Apply vacuum. Vacuum should not bleed off. If vacuum is being lost, replace one-way check valve. c. Connect a hand-operated vacuum pump to vacuum source end of check valve. Apply vacuum. Vacuum should flow through valve. If vacuum is not flowing, replace one-way check valve. Seal the fitting at opposite end of valve with a finger and apply vacuum. If vacuum will not hold, diaphragm within check valve has ruptured. Replace valve.

Related entry:

bmw 320d e46 vacuam pipe outlay, chevy 1985 4 3 liter emmision hose diagram, 1986 nissan 300zx vacuum diagram, Northstar 4 6 engine vacuum line connections, 2002 lincoln ls vacuum diagram u tube, 2000 monte carlo vaccum lines on upper manifold, vacuum line diagram for 1999 suburban, vacume diagrahm 95oldsmobile aurora, how to conect vacuum supply line on 1999 intrepid, 1992 buick lesabre cruise control vacuum hose routing,

2005 Chevrolet Malibu Vacuum Brake Booster Check Valve and/or Hose Replacement Removal Procedure

0

Filed Under (Chevrolet) by admin on 19-10-2010

download
1. Disconnect the brake booster vacuum check valve (1) from the brake booster. 2. If the vacuum check valve (1) needs to be separated from the vacuum hose (3), release and reposition the clamp (2) on the vacuum hose (3) and remove the check valve (1) from the hose (3). 3. If replacing the vacuum check valve (1), remove the grommet (4) from the brake booster and discard the grommet. 4. If removing the vacuum hose (2), take note of the vacuum hose routing then disconnect from the engine intake manifold connection (3) by releasing tension on the vacuum hose clamp (1) and sliding the vacuum hose (2) off the intake manifold connection (3). Installation Procedure Important: A small amount of denatured alcohol can be used as an assembly aid when installing the vacuum check valve and/or grommet. Do NOT use soap. 1. If the vacuum hose (2) was removed, install the vacuum hose into position on the vehicle as noted prior to removal, then connect the vacuum hose (2) to the engine intake manifold connection (3) and secure with the vacuum hose clamp (1). 2. If the vacuum check valve (1) is being replaced, install a NEW grommet (4) to the brake booster. 3. If the vacuum check valve (1) was separated from the vacuum hose (3), install the check valve (1) to the vacuum hose (3). Install and secure the clamp (2) into position on the hose (3). 4. Connect the brake booster vacuum check valve (1) to the brake booster.

Related entry:

1992 buick lasabre cruise control vacuum hose routing, 98 metro 1 0 vacuum hose diagram, 3 0 mazda tribute hose diagram, diagram of 2000 oldsmobile alero oxigene hose clamps, 2005 passat 1 8 vacum hoses, vacum hose routing for a 2004 navigator, 2001 taurus vacuum line diagram, replace vacuum hoses on 97 s10 pickup 2 2 engine, 91 geo storm vacuum hose routing diagram, 2002 ranger vacuum hose,

2000 Toyota Corolla CE Heating and Air Conditioning Control Assembly Removal and Installation

0

Filed Under (Toyota) by admin on 06-05-2011

download
12. REMOVE A/C CONTROL ASSEMBLY Remove the 2 screws and pull out the A/C control assembly, then disconnect the connector. NOTE: Be careful not to vent the mode control cable, when pull out the A/C control assembly. INSTALLATION 1. INSTALL A/C CONTROL ASSEMBLY a. Connect the connector. b. Pass the heater control cables as shown in the illustration. COMPONENTS REMOVAL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. REMOVE COWL SIDE TRIMS REMOVE FRONT DOOR SCUFF PLATES REMOVE LOWER FINISH PANEL REMOVE LOWER INSERT PANEL REMOVE CENTER CLUSTER FINISH PANEL REMOVE HEATER TO RESISTOR NO.2 DUCT REMOVE LOWER PANEL REMOVE REAR CONSOLE BOX REMOVE SHIFTING HOLE BEZEL REMOVE FINISH LOWER CENTER PANEL 11. DISCONNECT HEATER CONTROL CABLE c. Install the 2 set screws. 2. CONNECT HEATER CONTROL CABLES a. Set Air inlet control lever at “RECIRC” position b. Set Temperature control dial at “MAX. COOL” position c. Set Mode control dial at “DEF” position Zoom d. Adjust air inlet control cable. Set air inlet damper control lever to “RECIRC” position and connect the inner cable to lever pin and clamp the outer cable. HINT: Lock the clamp while lightly pushing the outer cable to the direction shown by arrow in the illustration. Sized for Print Zoom e. Adjust air mix control cable. Set air mix damper control lever to “MAX. COOL” position and connect the inner cable to lever pin and clamp the outer cable. HINT: Lock the clamp while lightly pulling the outer cable to the direction shown by arrow in the illustration. Sized for Print

Related entry:

1967 chevelle installing heat and air cable, 2000 dodge dakota heater control cable, 2005 toyota corolla throttle body relearn, How to adjust heater control cable on a 1995 dodge dakota, how to put heater cables with air 66chevelle, toyota corolla 2009 control cable air conditioning,

1993 Audi 100 A/C CLIMATE CONTROL COMMON PROBLEMS

0

Filed Under (Audi) by admin on 19-06-2010

download
5.- There are at least 5 reasons the compressor clutch will shut-off and not register a DTC: – A/C system is manually turned off. – Ambient temperature too low. – Engine overheat signal from the 4 terminal multi-function temperature sensor. – Load signal from the engine control unit (shut-off for up to 12 seconds). – Kickdown signal from TCM (shut-off for up to 12 seconds). DIAGNOSIS PROCEDURE 1. – Print DTC (additionally, read control head diagnostic display, channel 1, on cars with automatic climate control), then erase DTC. 2. – Check control head coding on cars with automatic climate control. Check compressor clutch control module coding level on cars with manual A/C.