2001 saturn l200
You are searching repair manual in PDF format about 2001 saturn l200 use another keyword for search another post or files
2001 saturn l200 Direct Download speed 5787 Kb/s
2001 saturn l200 Full Version speed 6767 Kb/s
Filed Under (Ford) by admin on 27-04-2010
ISSUE Some 2001-2005 Taurus/Sable, 2001-2006 Escape and 2005-2006 Mariner vehicles built prior to
1-17-2006 equipped with the 3.0L 4V Duratec engine may exhibit a ticking noise from the left bank cylinder head, with the engine at normal operating temperature only.
ACTION To diagnose, with the engine running and warm (normal operation temperature), using a mechanic’s stethoscope determine if the ticking noise is coming from the left hand intake camshaft at cylinder number 6, (Figure 1). If the ticking noise can be verified, refer to the following Service Procedure.
Filed Under (Mitsubishi) by admin on 18-12-2010
Function The original intercooler for the L200 is quite small. Because of this the cooling capacity is low and the pressure drop is considerable. When increasing the power output of the L200 engine the boost air temperature must be kept as low as possible, while it has a great influence in performance as well as engine durability. Charge air cooling also has a positive effect on exhaust emissions from diesel engines. The pressure drop through the charge air cooler lowers the air mass flow trough the engine. To maximize air mass flow is essential to increase performance. The sttemtec charge air cooler upgrade maximizes the cooling capacity and minimizes the pressure drop of the charge air cooler without any negative effects of the vehicle. List of content 1. Charge air cooler 2. Air hose 3. Bag, Brackets and rubber mountings for intercooler Installation Installation preparations 1. Perform test drive with verification of general engine functions. 2. Wash engine bay with special attention to radiator and intercooler (wash, compressed air). System installation Remove the radiator grille by first remove the four plastic clips and then the claws by pulling out and up.
Filed Under (Saturn) by admin on 01-10-2010
Automatic Transaxle 2-3 Shift Flare During First Minutes of Driving After Cold Soak (Perform Bulletin Procedure) Models: 2002 Saturn S-Series Vehicles with Automatic Transaxle (RPOs MP6, MP7) Attention: General Manager, Fixed Operations Manager, Parts Manager, Technician Condition: Some customers of 2002 S-series vehicles with MP6 or MP7 automatic transaxles may comment on a 2-3 shift flare during the first few minutes of driving after vehicle cold soak. Cause: This condition may be caused by improper pressure, a leak in the 2nd clutch circuit, improper clutch plate finish on 2nd and 3rd clutches, a restriction in the 3rd clutch oil delivery path in the end cover, or improper surface finish in the piston bores of the 2-3 clutch housing. Correction: To correct this condition, duplicate by cold soaking the vehicle the amount of time at temperature described by the owner. Refer to procedure in this bulletin. Service Procedure Verify proper transaxle pressures by installing gauge and performing stepped pressure test after cold soak. Refer to “Stepped Pressure Test” procedure in the 2002 Saturn S-Series Automatic Transaxle Service Manual. ^ If pressures are low, follow the diagnostic chart for DTC P0745 for possible causes of low pressure. Refer to “P0745 – PC Solenoid Pressure Low” diagnostic in the 2002 Saturn S-Series Automatic Transaxle Service Manual. ^ If pressures are within normal ranges, proceed to Step 2. Remove the transaxle end cover. Refer to “End Cover Replacement” in the 2002 Saturn S-Series Automatic Transaxle Service Manual. Check torque on input shaft nut and end cover 3rd clutch oil passage for restrictions. ^ Input shaft nut torque should be 150 N.m (111 ft-lb). If nut is found to be loose, remove nut, clean threads and install new nut using Service Manual procedures and proceed to check 3rd oil passage. ^ Check 3rd oil passage in the end cover by pouring transaxle fluid through it and another passage. If the passage is restricted, you will notice significantly less fluid flow through it. If 3rd clutch passage is found to be restricted, install new end cover per Service Manual procedures and retest for concern. ^ If nut and 3rd clutch passage are okay, proceed to Step 4. Remove transaxle from vehicle. Refer to “Transaxle Removal” in the 2002 Saturn S-Series Automatic Transaxle Service Manual. Disassemble transaxle and install new 2-3 clutch housing, clutch pistons and clutch plates. Refer to “Transaxle Disassemble” in the 2002 Saturn S-Series Automatic Transaxle Service Manual.
Filed Under (Buick) by admin on 14-11-2010
Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville steering vibration, shudder or moan noise when steering during parking maneuvers on dry pavement. Correction Install a new power steering pressure (inlet) hose assembly on the following vehicles: • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra Install a new power steering pressure (inlet) and return (outlet) hose assembly on the following vehicles: • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville 1. Verify that the power steering pump reservoir is full. • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. Verify proper belt tension and operation of the belt tensioner. Check for power steering hose ground out conditions. Check for good engine idle and correct engine RPM. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used 2. 3. 4. 5. 6.
Filed Under (Chevrolet) by admin on 21-10-2010
Models: 2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission (RPOs MN3, MN7, M15, M76) Condition Some customers may comment on a 1-2 shift shudder at light to moderate acceleration. Typically, the throttle plate angle parameter is 12-20% at time of condition with vehicle speed of approximately 24-40 km/h (15-25 mph). The customer may describe the condition as slip or delayed shift into second. Correction Replace the complete second clutch assembly with service kit, P/N 24240561. Refer to the GM Unit Repair Service Manual for the year and model of the vehicle being serviced for the 2nd Clutch service procedure. This service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, other gaskets not included in this service kit will also be needed to complete the repair – a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering gasket kit 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to-Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve