2002 6 6 duramax fan clutch


You are searching repair manual in PDF format about 2002 6 6 duramax fan clutch use another keyword for search another post or files



  2002 6 6 duramax fan clutch Direct Download speed 5787 Kb/s

  2002 6 6 duramax fan clutch Full Version speed 6767 Kb/s




2002 Ford F 150 Cooling Fan – Blade, Clutch and Shroud Removal and Installation

0

Filed Under (Ford) by admin on 27-10-2010

download
WARNING: Do not run the engine while the protective components are removed. Failure to follow these instructions may result in personal injury. All vehicles 1. Remove the air cleaner assembly. 2. Drain the cooling system. Supercharged vehicles 3. Remove the supercharger degas bottle. All vehicles 4. Remove the front air deflector. 1 Remove the pin-type retainers. 2 Remove the front air deflector. 5. Remove the upper hose from the radiator. 1 Release the clamp. 2 Disconnect the hose. 6. Remove the degas bottle hose from the radiator. 1 Release the hose clamp and slide it away from the end of the hose. 2 Slide the overflow hose off the radiator fitting. 7. Remove the fan blade assembly and fan clutch. 1 Use the fan pulley holding wrench to hold the water pump pulley steady. 2 Use the fan clutch nut wrench to remove the fan blade and the fan clutch. 7. Remove the fan blade assembly and fan clutch. 1 Use the fan pulley holding wrench to hold the water pump pulley steady. 2 Use the fan clutch nut wrench to remove the fan blade and the fan clutch. 9. NOTE: If the lead retaining clip is broken, install a new lead retaining clip. If equipped, disconnect the fan clutch electrical connector and lead retaining clip. 10. Remove the fan blade and fan shroud out of the vehicle together. 11. Remove the bolts and separate the fan blade assembly from the fan clutch. 12. NOTE: To avoid stripping the threads, use the correct bolts when installing a new fan clutch. Use’ bolts 575632-S426 for fan clutch F85A-8A616 and bolts N602548-S426 for fan clutch 2L34-8A616 and 2C64-8A616. To install, reverse the removal procedure.

2004 Chevy Silverado 3500 Fan Clutch: Service and Repair Fan Clutch Replacement

0

Filed Under (Chevrolet) by admin on 20-08-2010

download
Removal Procedure 1. Remove the upper fan shroud. 2. Install the J 46406 to the fan clutch. 3. Remove the fan hub nut from the water pump in a counterclockwise rotation. 4. Remove the fan clutch bolts from the rear of the fan blade. 5. Separate the fan clutch from the fan blade. Installation Procedure 1. Install the fan clutch bolts from the rear of the fan blade. 2. Notice: Refer to Fastener Notice in Service Precautions. Install the fan clutch bolts. Tighten the bolts to 23 Nm (17 ft. lbs.). 3. Install the fan assembly. 4. Install the J 46406 to the fan clutch. Tighten the nut clockwise to 56 Nm (41 ft. lbs.). 5. Install the upper fan shroud.

2005–2006 Toyota Tacoma CLUTCH PEDAL SQUEAK NOISE

0

Filed Under (Toyota) by admin on 04-06-2011

download
Some customers may complain about a “squeak” or “creak” noise when depressing or releasing the clutch pedal. The clutch master cylinder clevis assembly has been improved to eliminate this condition. Repair Procedure 1. Record all radio presets before starting. 2. Disconnect the negative (–) battery terminal cable. 3. Remove the clutch pedal sub–assembly. A. Remove the front door opening trim LH (scuff plate). B. Remove the cowl side trim board. C. Remove the instrument panel finish panel lower No. 1. D. Remove the driver’s side Junction Block. E. Remove the turnover (compression) spring. F. Remove the bolt attached to the instrument panel reinforcement assembly. G. Remove the clutch pedal sub–assembly. a. Remove the bolt and nut. b. Remove the clutch pedal from the clutch pedal support. 4. Remove the clutch pedal spring holder from the clutch pedal support. 5. Remove the clutch pedal pad. 6. Remove the two (2) clutch pedal bushes from the clutch pedal. 7. Remove the clutch pedal shaft collar. 8. Using needle–nose pliers, remove the No. 1 cushion from the clutch pedal. 9. Install the clutch pedal No. 1 cushion on the NEW clutch pedal sub–assembly. NOTE: Install parts on the NEW clutch pedal sub–assembly BEFORE installing in the vehicle. 10. Install the clutch pedal shaft collar. A. Apply MP grease to the clutch pedal shaft collar. B. Install the clutch pedal shaft collar onto the clutch pedal. 11. Install the clutch pedal bushes. A. Apply MP grease to the two (2) NEW bushes. B. Install the two (2) bushes onto the clutch pedal. 12. Install the clutch pedal pad. 13. Install the clutch pedal spring holder. A. Apply MP grease to the contact surface of the clutch pedal spring holder. B. Install the clutch pedal spring holder. 14. Remove the clevis sub–assembly. A. Measure length “A” of the clutch master cylinder. a. Measure length “A” between the lock nut and the thread end with a ruler. b. Record length “A”. B. Remove the clevis sub–assembly from the master cylinder. a. Loosen the lock nut. b. Rotate and remove the clevis sub–assembly. 15. Install the NEW clevis sub–assembly. A. Rotate the lock nut to match length “A”. B. Rotate and install the NEW clevis sub–assembly to contact the lock nut. C. Tighten the lock nut and torque to specification. Torque: 11.8 NSm (120 kgfScm, 8.7 ftSlbf) D. Apply MP grease to the ball end of the clevis sub–assembly where it will contact the clutch pedal. 16. Install the NEW clutch pedal sub–assembly. A. Install the clutch pedal onto the clutch support with the bolt and nut. Torque: 34 NSm (347 kgfScm, 25 ftSlbf) HINT: Install the bolt from the left side of the vehicle. B. Apply MP grease to the clutch pedal sub–assembly where the clevis sub–assembly contacts the clutch pedal. NOTE: Failure to apply grease to the clevis and clutch pedal sub–assemblies could cause the noise to return. C. Tighten the bolt to the instrument panel reinforcement assembly. Torque: 8 NSm (82 kgfScm, 6 ftSlbf) 17. Install the turnover (compression) spring. A. Apply MP grease to the contact surface of the spring holder, clutch pedal, and spring. B. Install the spring onto the clutch pedal and spring holder.

2006 Chevy Avalanche 1500 Fan Clutch Replacement

0

Filed Under (Chevrolet) by admin on 26-08-2010

download
Removal Procedure 1. Remove the upper fan shroud. 2. Install the J 46406 and the J 41240-5A to the fan clutch. 3. Remove the fan hub nut from the water pump in a counterclockwise rotation. 4. Lay the fan blade face down on a workbench. 5. Remove the fan clutch bolts from the rear of the fan blade. 6. Separate the fan clutch from the fan blade. Installation Procedure 2006 Chevy Truck Avalanche 1500 2WD V8-5.3L VIN T 1. Install the fan clutch bolts. 2. Install the fan clutch onto the fan blade. Notice: Refer to Fastener Notice in Service Precautions. 3. Install the fan clutch bolts. ^ Tighten the bolts to 23 Nm (17 ft. lbs.). 4. Install the fan blade. 5. Install the J 46406 and the J 41240-5A to the fan clutch. ^ Tighten the fan clutch nut clockwise to 56 Nm (41 ft. lbs.). 6. Install the upper fan shroud.

2003 Chevy TrailBlazer Radiator Cooling Fan: Description and Operation

0

Filed Under (Chevrolet) by admin on 29-08-2010

download
Cooling Fan Control The purpose of the Electro-Viscous (EV) fan clutch is to maintain powertrain cooling requirements. The Powertrain Control Module (PCM) monitors the following sensors to regulate the fan speed; – Engine coolant temperature sensor – A/C refrigerant pressure sensor – Vehicle speed sensor – Intake air temperature sensor – Transmission fluid temperature sensor – Ambient air temperature sensor The PCM controls the electro-viscous fan clutch engagement. The PCM regulates a 12-volt pulse width modulated signal (PWM) to the cooling fan relay. The PWM signal determines the ON time of the relay. As the commanded state of the fan clutch increases, so does the ON time of the relay. This ON time directly effects the amount of time the solenoid, which is internal to the fan clutch, is energized. When the solenoid in the fan clutch is energized, it opens the spring loaded valve and allows fluid to flow from the storage chamber to the fluid coupling of the cooling fan clutch, increasing the fan speed. When the solenoid is de-energized, the spring loaded valve closes, and blocks the path of the fluid to the fluid coupling of the fan clutch, reducing fan speed. The fan has the ability to create a feedback signal, so the PCM has an actual fan speed input. This is done with a hall effect sensor internal to the fan clutch. The PCM supplies a 5-volt reference and a low reference to the hall effect sensor. The hall effect sensor returns a signal pulse through the cooling fan speed signal circuit in response to the reluctor track passing by the magnetic field of the hall effect sensor. The PCM commands the cooling fan to 100% under the following conditions: – Engine coolant temperature exceeds approximately 129°C (264°F). – The transmission oil temperature exceeds approximately 151°C (304°F). – A/C refrigerant pressure exceeds 1655 kPa (240 psi). – When certain DTC’s set. These include P0116, P0117, P0118, P0125, P1481, P1482, and P1484.