download
Trim Panels, Mouldings And Fasteners NOTE: Floor console with navigation shown, floor console without navigation similar. Trim Panels And Fasteners NOTE: Floor console with navigation shown, floor console without navigation similar. Removal and Installation 1. Place the selector lever in the NEUTRAL position. 2. Position the front seats to the full rearward and downward positions. 3. Pull the middle and rear of the floor console LH and RH lower trim panels outward to release the retaining clips. 4. NOTICE: Damage to the floor console upper trim panels may occur if cardboard is not used to remove the floor console lower trim panels. NOTE: Floor console LH lower trim panel shown, floor console RH lower trim panel similar. Position a piece of cardboard between the floor console LH and RH lower trim panels and floor console. 5. Remove the floor console LH lower trim panel. Push the floor console LH lower trim panel toward the front of the vehicle to detach the trim panel from the pin-type retainer. 6. Remove the floor console RH lower trim panel. Pull the floor console RH lower trim panel down toward the floor of the vehicle to detach the trim panel from the pin-type retainer. 7. Position the front seats forward. 8. Remove the 2 floor console lower rear screws. 9. Position the front seats rearward. 10. Remove the steering column opening trim panel in the following sequence. 1. Remove the 2 steering column opening trim panel screws. 2. Pull the steering column opening trim panel down toward the floor of the vehicle to release the retaining clips. 11. Remove the floor console LH and RH finish mouldings in the following sequence. 1. Lift up the rear of the floor console finish mouldings to release the retaining clips from the floor console. 2. Pull the floor console finish mouldings toward the rear of the vehicle to release the retaining clips from the center instrument finish panel. 3. Disconnect the trunk release switch and start/stop button electrical connector, if equipped. NOTICE: Damage to the floor console may occur if cardboard is not used to remove the floor console upper trim panel. NOTE: Floor console LH upper trim panel shown, floor console RH upper trim panel similar. 12. Remove the floor console LH upper trim panel in the following sequence. 1. Pull the rear of the floor console LH upper trim panel away from the floor console, releasing the retaining clips. 2. Position a piece of cardboard between the floor console LH upper trim panel and floor console. 3. Pull the floor console LH upper trim panel toward the rear of the vehicle to release the retaining clips from the instrument panel. 13. Remove the 2 pushpin carpet retainers, 4 floor console lower front and middle screws. 14. Remove the selector lever bezel. For additional information, refer to Section 307-05. 15. Remove the media bin/storage compartment in the following sequence. 1. Remove the 4 screws and lift up the media bin/storage compartment. 2. Disconnect the electrical connector(s). 16. Disconnect the floor console bulkhead electrical connector. 17. Detach the wire harness pin-type retainer from the floor console. 18. Remove the 2 floor console upper bolts. 19. Disconnect the selector lever cable from the selector lever.

download
Special Tools Required KTC trim tool set SOJATP2014 * * Available through the American Honda Tool and Equipment Program. NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage when removing components. Take care not to scratch the front seat, dashboard, and related parts. 1. Detach the clips (A, B), and release the hooks (C) by pulling the center console trim (D) from both sides. 2. Open the console box lid (A) then remove the console mat (B) and screws (C, D). 3. Slide the rear section of the center console (A) rearward to release the hooks (B). 4. Lift up the rear of the console (A). Release the harness retainer clip (B) from the air duct, and disconnect the console accessory power socket connector (C), the light bulb socket connector (D), and the AUX connector (E), then remove the rear section of the center console. 5. Install the console in the reverse order of removal, and note these items: Check if the clips are damaged or stress-whitened, and if necessary, replace them with new ones. Push the clips into place securely. Make sure the console accessory power socket connector and the AUX connector are plugged in properly, and the light bulb socket is connected securely.

download
AR68.20-P-2020GI Remove/Install Rear Center Console – Models 163.154/174 #A as of 289565 – Models 163.157/175 (all) Remove/Install 1 Remove armrest lid (1) 2 Remove stowage box in the center console NOTE: Press the center pin approx. 4 mm downwards, then remove the rivet upwards 3 Remove screws (2) on the cup holder 4 Remove inner part of ashtray 5 Remove ashtray trim (3) CAUTION: Risk of breaking the clips (4) NOTE: Loosen clips (4) and pull back the lower edge of the cover and remove upwards 6 Remove screws (5) 7 Unclip rear center console (6) above (arrows) Long wedge: See Special Tools below. 8 Remove rear center console (6) from the center console 9 Disconnect plug from control module of rear control panel and ashtray NOTE: Disconnect plug of the rear ashtray from ashtray housing 10 Install in the reverse order Special Tools Long Wedge P/N # 115 589 03 59 00

download
1. Remove the screws that hold storage bin in place. 2. Remove the storage bin from the center console. Fig. 108: Console Storage Bin 1. Install the storage bin. 2. Install the storage bin screws. Tighten: Tighten the screws to 2 N.m (18 lb in). TRIM PLATE REPLACEMENT – CONSOLE UPPER Removal Procedure Fig. 109: Console Upper Trim Panel 1. Remove the shift handle. Refer to Floor Shift Control Knob Replacement in Automatic Transmission. 2. Remove the console storage bin. Refer to Console Storage Bin Replacement . 3. Remove the cup holder/PRNDL assembly. Refer to Cupholder Replacement . 4. Remove the center console end panel. Refer to Center Console End Panel Replacement . 5. Pull upwards on the upper console trim panel to release the trim panel clips. 6. Remove the upper console trim panel.

download
Special Tools Required KTC trim tool set SOJATP2014 Without Console Armrest NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. Take care not to scratch the front seat, dashboard, and related parts. 1. Detach the clips (A, B) by pulling the center console box (C) up, and removing it from the center console (D). 2. M/T model: Remove the shift knob (A). 3. Remove the screws (A, B) and clips (C), and remove the center console (D). 4. Install the console in the reverse order of removal, and note these items: Replace any damaged clips. Push the clips into place securely. With Console Armrest NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. Take care not to scratch the front seat, dashboard, and related parts. 1. M/T model: Remove the shift knob (A).