2002 ford ranger slave cylinder


You are searching repair manual in PDF format about 2002 ford ranger slave cylinder use another keyword for search another post or files



  2002 ford ranger slave cylinder Direct Download speed 5787 Kb/s

  2002 ford ranger slave cylinder Full Version speed 6767 Kb/s




2000 Ford F-Super Duty 250-550 Clutch Master Cylinder and Reservoir REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 08-03-2011

download
Removal CAUTION: Remove the entire clutch hydraulic system from the vehicle as an assembly when installing a new clutch master cylinder assembly (7C522). 1. Disconnect the clutch hydraulic tube from the dash clip. 2. Raise and support the vehicle. For additional information, refer to Section 100-02. 3. Unlock and remove the slave cylinder (7A564) from the transmission. Compress and twist the slave cylinder to unlock it from the transmission. 4. Disconnect the clutch hydraulic tube from the floor pan clip. Position the slave cylinder and hydraulic tube forward below the left engine bank. This will make it easier to unlock the clutch master cylinder from the clutch pedal and support bracket (7B633) by reducing tension on the hydraulic tube. 5. Lower the vehicle. 6. WARNING: The clutch pedal is under spring tension. Unlock the push rod bushing retaining clips and separate the clutch master cylinder push rod from the clutch pedal. 7. Remove and discard the push rod bushing (7526). 8. Remove the switch cover, and remove the clutch pedal position switch (7C534) from the clutch master cylinder push rod. 9. Separate the power distribution box from the bracket to gain access to the clutch master cylinder. 10. Unlock and remove the clutch master cylinder from the clutch pedal and support bracket. Compress and twist the clutch master cylinder clockwise 45 degrees to unlock it from the clutch pedal and support bracket. 11. Remove the clutch hydraulic reservoir from the wiring tray and separate the clutch hydraulic tube from the brake master cylinder assembly. Position the clutch hydraulic reservoir aside. 12. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, wash the surface with water immediately. Remove the clutch hydraulic system from the vehicle. 13. Clean the clutch hydraulic system components to prevent contaminants from entering the hydraulic system. 14. CAUTION: Place a suitable container under the clutch master cylinder. Disconnect the hydraulic tube from the clutch master cylinder. 1. Using a 3/32-inch punch and a hammer, drive out the roll pin, and discard it. 2. Disconnect the hydraulic tube from the clutch master cylinder.

Related entry:

1984 F350 Clutch Cable Install, 2000 ford f750 clutch slave cylinder, 2008 Masda b2300 transmisson clutch slave clylinder how to bleed system, how to install slave cylinder in 1984 ford truck, how to replace clutch master cylinder on 06 jetta, how to replace clutch slave cylinder on a 650 ford, how to replace clutch slave cylinder on a 650 ford truck, location of bleeder on 1990 f250 manual transmission, on a 1998 cavalierz24 how do you remove the master cylnder assembly, procedure replacing a master cylinder on 1999 ford escort,

1999 Kia Sportage Clutch Slave Cylinder: Service and Repair

0

Filed Under (KIA) by admin on 15-09-2010

download
RELEASE CYLINDER Removal To prevent loss of brake fluid during clutch slave cylinder removal, the disconnected steel hydraulic line must be plugged or directed into a suitable container. 1. Disconnect flexible hose from steel hydraulic line. NOTICE: Twisting may damage the flex hose. 2. Remove hydraulic line retainer clip. 3. Remove two bolts. Disassembly 1. Remove flexible hose, boot, and push rod. 2. Remove piston and cap assembly and return spring. 3. Remove bleeder cap, bleeder screw, and steel ball. 4. Use brake fluid to clean inner parts. Inspection After cleaning, inspect the following parts: 1. Release cylinder bore and piston for wear. 2. Weak return spring. Assembly 1. Coat the piston and cups with clean brake fluid. 2. Insert steel ball in cylinder bleeder hole and secure with bleeder screw. 3. Push bleeder cap over bleeder screw end. 4. Insert return spring and piston and cup assembly into cylinder bore. 5. With boot installed on push rod, insert rod into cylinder bore and snap boot in place. 6. Connect flexible hose to the cylinder body. Tighten flexible hose nut to 16 ft. lbs. (22 Nm). Installation 1. With cylinder push rod in clutch arm detent, attach cylinder to the transmission case with two bolts. Tighten bolts to 17 ft. lbs. (23 Nm).

FORD LIGHT TRUCK: 1993 AEROSTAR, BRONCO, EXPLORER, F-150-350 SERIES, F-47, RANGER UNRESPONSIVE CLUTCH: AIR ENTRAPPED IN HYDRAULIC SYS

0

Filed Under (Ford) by admin on 07-01-2011

download
ISSUE A “soft” unresponsive clutch pedal may be felt or the driver may be unable to release the clutch. This is caused by air entrapped in the clutch hydraulic system. ACTION Use the information in this TSB article in addition to the appropriate bleeding procedure. This article includes detail as well as extra service tips for easier hydraulic clutch bleeding. The clutch hydraulic system for the 1993 model year is new and more difficult to bleed than the previous hydraulic system. Therefore, a different bleeding procedure is required for these vehicles. RANGER, EXPLORER, AEROSTAR The most difficult systems to bleed are on the Ranger, Explorer, Aerostars. NOTE: When installing dry clutch cylinder or tube service parts, do the bench bleed procedure first. BENCH BLEED The compact vehicles are more difficult to bleed because the downward angle of the master cylinder makes it difficult for air to escape up into the reservoir. Therefore, if the master cylinder is removed from the vehicle and bled while held in a vertical orientation (a bench bleed) air can escape much more efficiently. Refer to Fig. 1 . BENCH BLEEDING PROCEDURE (CONCENTRIC SLAVE CYLINDER) 1. Remove master cylinder, line and reservoir from vehicle and assemble with replacement parts required based on initial concern. 2. Hold the master cylinder vertically with the reservoir feed hose in the highest position on the body. See Fig. 1 . 3. Fill the reservoir and extend above the master cylinder and assure the quick connect on the clutch line is below the master cylinder. (Lightly clamp reservoir in a vise). 4. Using a small screwdriver, depress the internal mechanism of the male quick connect coupling to open the valve. See Fig. 1 . 5. Stroke and hold master cylinder pushrod. 6. Close quick connect valve. 7. Release master cylinder pushrod. 8. Fill reservoir. 9. Repeat Steps 4 through 8 four more times. 10. With the master cylinder still being held with the outlet tube and reservoir feed tube ends high, quick connect closed and the reservoir full, proceed as follows: a. Push the pushrod into the body several times quickly to expel any remaining air. b. If it is a remote reservoir, pinch the supply hose with your fingers two or three times to help move air into reservoir. 11. When the movement of the pushrod is .130″ (4mm) or less when stroked in Step 10, reinstall the master cylinder into the vehicle and couple it to the slave cylinder.

Related entry:

how to bleed the hydraulic pump of slk 230,

Ford Ranger upper ball joint replacement 1998-2002 Ford Ranger 2 wheel drive

0

Filed Under (Ford) by admin on 18-04-2010

download
Repair Procedure:
1. Raise vehicle on hoist, and support lower control arm. 2. Remove wheel and tire assembly. 3. Mark position of upper eccentric camber bolts. 4. Remove upper ball joint spindle nut and pinch bolt, 5. Separate upper ball joint from spindle. 6. Remove nuts and camber bolts attaching upper control arm-to-frame, 7. Remove upper control arm. 8. Place control arm in vise, press ball joint out with ball joint press. See Fig. 1. 9. After ball joint has been pressed out install new ball joint (500-1109) with the words “install inboard” facing toward the inboard side of control arm. See Fig. 2. Incorrect installation may cause damage to the ball joint 10. Install ball joint boot with words “install inboard” towards the inboard side of control arm. See Fig. 3. 11. Install upper control arm. 12. Align upper eccentric camber bolts with marks made during removal. 13. To complete installation, reverse removal procedure. Tighten bolts and nuts to specification. Then check wheel alignment

Related entry:

2001 ford ranger clock spring, 2003 Ford Ranger Alternator Replacement, installing upper control arms on a 1998 ford ranger, remove truck bed 1997 ford ranger, how to replace timing belt ford ranger 2 5 td, 1997 ford ranger bed removal, 1989 ford ranger repair manual download, 2003 ranger firing order, ford ranger tdci 2010 injector no power whts the problem, ford ranger troubleshooting symbols,

2004 Suzuki Forenza Concentric Slave Cylinder Removal and Installation Removal

0

Filed Under (Suzuki) by admin on 30-10-2010

download
1. Remove the transaxle from the vehicle. 2. Remove the concentric slave cylinder retaining bolts. 3. Disconnect the concentric slave cylinder pipe from the concentric slave cylinder. 4. Remove the bushing from the concentric slave cylinder pipe in the transaxle housing. 5. Remove the concentric slave cylinder pipe. 6. Remove the O-ring and the concentric slave cylinder. Installation 1. Install the concentric slave cylinder and the pipe. 2. After installing the pipe screw provisionally, tighten the concentric slave cylinder retaining bolts. Tighten the concentric slave cylinder retaining bolts to 7 Nm (62 inch lbs.) . 3. Tighten the pipe screw. Tighten the pipe screw to 15 Nm (11 ft. lbs.) . 4. Install the bushing onto the transaxle housing. 5. Connect the pipe with bushing. 6. Install the transaxle into the vehicle.