2002 isuzu trooper 3.2l timing marks


You are searching repair manual in PDF format about 2002 isuzu trooper 3.2l timing marks use another keyword for search another post or files



  2002 isuzu trooper 3.2l timing marks Direct Download speed 5787 Kb/s

  2002 isuzu trooper 3.2l timing marks Full Version speed 6767 Kb/s




2003 TOYOTA TACOMA TIMING BELT INSTALLATION REMOVAL

0

Filed Under (Toyota) by admin on 13-01-2011

download
NOTICE: Always turn the crankshaft clockwise. (c) Check that the timing marks of the camshaft timing pul- leys and No.3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°). (d) Remove the crankshaft pulley bolt. IF REUSING TIMING BELT, CHECK INSTALLATION MARKS ON TIMING BELT Check that there are 3 installation marks and front mark on the timing belt. If the installation and front marks have disappeared, before re- moving the timing belt, place 3 new installation marks on the timing belt to match the timing marks of the timing pulleys, and place a new front mark on the timing belt. 18. 19. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt ten- sioner and dust boot. 20. REMOVE TIMING BELT 21. (a) REMOVE RH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 22. (a) REMOVE LH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 23. REMOVE NO.2 IDLER PULLEY Remove the bolt and idler pulley. 24. REMOVE NO.1 IDLER PULLEY Using a 10 mm hexagon wrench, remove the pivot bolt, idler pulley and plate washer. 25. REMOVE CRANKSHAFT TIMING PULLEY Remove the timing pulley. HINT: If the pulley cannot be removed by hand, use SST and a service bolt to remove the timing pulley. SST 09950–50011 (09951–05010, 09952–05010, 09953–05020, 09954–05011)

Related entry:

2003 opel vivaro 1 9 dci service manual pdf, 1azfe removing crank pulley, nissan navara 3lt timming marks 1996 v6, 2005 mazda 6 2 3l engine timing marks, 2004 Chrysler Pacifica Timing Marks, 2007 Suzuki Forenza Timing Marks, YouTube 07 mazda cx 7 setting timing chain, youtube setting timing chain on 07 mazda cx 7, timming belt diagrame for a toyota 1kz te, cx7 mazda 07 timing on variable pic,

1995 Isuzu Trooper LS REMOVAL & INSTALLATION TIMING BELT

0

Filed Under (Isuzu) by admin on 05-05-2010

download
Aligning Timing Belt Sprockets (DOHC) Aligning Camshaft Timing Marks (DOHC) Exploded View Of Cylinder Head Components (SOHC
Shown; DOHC Is Similar) 1. Ensure all timing marks are aligned. Install belt over one pulley at a time starting at crankshaft sprocket
and working counterclockwise. Belt should go over tensioner last. Secure belt at each pulley during
installation with pinch clips. See Fig. 5 . 2. Compress timing belt tensioner pusher and insert pin to retain pusher. Apply pressure to tensioner against belt, and install tensioner pusher. Tighten bolts to specification. See TORQUE SPECIFICATIONS . 3. Loosen tensioner pulley bolt. Apply pressure on belt by rotating tensioner. Tighten tensioner pulley bolt to specification.. See TORQUE SPECIFICATIONS . Remove pin from timing belt tensioner pusher. 4. Remove pinch clips from timing belt (if used). Install crankshaft pulley, tightening center bolt finger tight. Rotate crankshaft 2 turns clockwise. Ensure timing belt tensioner pusher rod protrudes proper

Related entry:

Free Car Manuals Isuzu Trooper 1993, 1993 isuzu trooper ls 4wd, 96 isuzu trooper rotor change instructions with diagram,

1996 Chevrolet Monte Carlo Camshaft Timing COMPLETE CAM TIMING PROCEDURE

0

Filed Under (Chevrolet) by admin on 10-08-2010

download
T] EXHAUST CAMSHAFT (RIGHT) T| INTAKE CAMSHAFT (RIGHT) T] SECONDARY TIMING BELT IDLER PULLEYS T) INTAKE CAMSHAFT (LEFT) 7] EXHAUST CAMSHAFT (LEFT) T] COOLANT PUMP T] INTERMEDIATE SHAFT BELT SPROCKET T] SERPENTINE BELT TENSIONER T| SECONDARY TIMING BELT TENSIONER PULLEY ??] GENERATOR ??] SECONDARY TIMING BELT TENSIONER ?2? SECONDARY TIMING BELT NOTE: START AT #7 AND INSTALL COUNTERCLOCIOMBE A LOCATION OF TIMING MARKS WITH CAM HOLD DOWN TOOLS J 38813 INSTALLED B FRONT COVER TIMING MARK C LOCATION OF TIMINS MARKS WITH DRIVE BELT IN- STALLED D LOCATION WHERE CAM HOLD DOWN TOOLS ARE INSTALLED RH EXHAUST CAMSHAFT SPROCKET RH INTAKE CAMSHAFT SPROCKET LH INTAKE CAMSHAFT SPROCKET LH EXHAUST CAMSHAFT SPROCKET PERMANENT MARKS PAINTED DOTS REMOVE PREVIOUS MARKS IF TIMING IS BEINS CHANGED AND MARK AGAIN IN THESE LOCATIONS TORSIONAL DAMPER INTERMEDIATE SHAFT SPROCKET NOTE: THIS TDC #1 EXHAUST. INTtRMEDlATE »HAFT BELT sprocket twno mark» at » o’clock (powtmo towards drain notch) NOTE : GM does not provide a timing mark diagram for belt installation without using the special tool(s) listed below. TOOLS REQUIRED: A J 38613 CamHold Down Tool A J 38614 Cam Sprocket Holding Tool NOTICE: If only one (1) bank is to be timed, make sure bank to bank earn timing relationship is one (1) revolution apart. Timing flats should be 180 degrees opposite (right bank versus left bank) when finally timed. 1. Remove all spark plugs. 2. Remove all camshaft sprockets. IMPORTANT: Remove oil from cam hold down tool bolt hole in carrier before installing and tightening bolt. 3. Rotate camshaft flats “up” and install J 38613. Tighten cam hold down tool bolt to 30 Nm (22 lb. ft). 4. Install all camshaft sprockets. 5. Timing belt by routing it around the idlers and sprockets. DO NOT bend, kink, or pry on belt as damage may occur. A. Start at intermediate cam sprocket and work counterclockwise. B. Make sure the belt is installed in direction of rotation. C. Engage teeth into all sprockets, place rubber hose behind belt at intermediate sprocket and accumulate slack at tensioner location. 6. Tensioner pulley to mounting base. A Use flat magnet, tape or cup plug to hold pivot tube in pulley during this step. Otherwise, pivot tube may fall out. A After starting pivot bolt, rotate arm counterclockwise to position square lug at 6 o’clock

Related entry:

4 3 Vortec Timing Procedure, colt 2 8 tdi manuel, 2003 lexus 3 0camshaft timing marks, 1az fe engine timing marks, timing mark on hino, pic of cam lobe top dead center on a 2004 suzuki forienza, timing marks for toyota twin cam 1600, diagram gor camshalf setting on 1995 corolla, Toyotatwincamtiming marks com, how to test a distributor cam sensor on a 1996 toyota camry,

1996 Mitsubishi Eclipse GS-T TIMING BELT & BALANCE SHAFT BELT Removal

0

Filed Under (Mitsubishi) by admin on 18-01-2011

download
1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. CAUTION: DO NOT rotate crankshaft counterclockwise. Ensure timing marks are aligned. If reusing timing belts, mark timing belts for direction of rotation. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. NOTE: Camshaft sprocket dowel pins will be in 12 o’clock position when timing marks are correctly aligned. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B”.

Related entry:

04 optra 2 0 l dtec timing marks, 1996 montero belt manual, ecotec balance shaft timing marks, how to tighten drive belts on mitsubishi triton03, 2004 lexus rx 330 timing belt failure, 03 p/t crucer valance shaft marks, how to set correct timing for mitsubishi lancer 4G15A, how to set timing marks using obx timing sprockets on mitsubishi eclipse 2 0 dohc, hyundai tucsan 2005 timing belt diagram, jhow tighting tenshon timing 2004 endeavor 3 8 engine,

2000 Isuzu VehiCROSS Timing Belt: Service and Repair Removal Installation

0

Filed Under (Isuzu) by admin on 21-09-2010

download
Removal 1. Disconnect battery ground cable. 2. Remove air cleaner assembly. 3. Remove radiator upper fan shroud from radiator. 4. Move drive belt tensioner to loose side using wrench then remove drive belt. 5. 6. 7. 8. 9. 10. 11. 12. Remove cooling fan assembly four nuts, then the cooling fan assembly. Remove cooling fan drive pulley assembly. Remove idle pulley assembly. Remove serpentine belt tensioner assembly. Remove power steering pump assembly. Remove crankshaft pulley assembly using J-8614-01 crankshaft holder, hold crankshaft pulley remove center bolt, then the pulley. Remove right side timing belt cover then left side timing belt cover. Remove lower timing belt cover 2000 Isuzu Truck VehiCROSS (4WD) V6-3.5L  13. Remove pusher. Caution: The pusher prevents air from entering the oil chamber. Its rod must always be facing upward. 14. Remove timing belt. Caution: 1. Do not bend or twist the belt. otherwise its core could be damaged. The belt should not be bent at a radius less than 30 mm. 2. Do not allow oil or other chemical substances to come in contact with the belt. They will shorten the life. 3. Do not attempt pry or stretch the belt with a screw driver or any other tool during installation. 4. Store timing belt in a cool and dark place. Never expose the belt to direct sunlight or heat. Installation Note: For correct belt installation, the leper on the belt must be able to be read as viewed from the front of the vehicle. 2000 Isuzu Truck VehiCROSS (4WD) V6-3.5L  1. Install timing belt. 1. Align groove of crankshaft timing pulley with mark on oil pump. Align the mark on the crankshaft timing pulley with alignment mark (white dots line) on the timing belt. Secure the belt with a double clip. Note: When timing marks are aligned, No.2 piston will be on top Dead Center.

Related entry:

2000 izsu ftr wirin diagram, repair on isuzu 320 frontier 1998 front suspension, 1989 Isuzu NPR truck service manuals, isuzu rodeo 95 alternator belt diagram, ISUZU NPR CODE 17, isuzu 6HE1 shopmanual, isuzu 4ze1 oil pump install, front crank pulley torque isuzu 4JJ1, 89 isuzu pick up can the clutch release lever come off the ball stud?, timing 4be1 isuzu,