2002 mitsubishi lancer rear brakes


You are searching repair manual in PDF format about 2002 mitsubishi lancer rear brakes use another keyword for search another post or files



  2002 mitsubishi lancer rear brakes Direct Download speed 5787 Kb/s

  2002 mitsubishi lancer rear brakes Full Version speed 6767 Kb/s




2002 Ford Ranger Brakes – Rear Brakes Grabbing Condition

0

Filed Under (Ford) by admin on 08-11-2010

download
Some vehicles may exhibit a grabbing condition from the rear brakes during the first few brake applications. The condition only occurs after the vehicle has been parked for several hours. ACTION Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE To service, reduce/minimize moisture intrusion into the rear drum brake assemblies by applying Motorcraft® Silicone Gasket and Sealant to the brake backing plate. 1. Place vehicle on hoist and remove the rear wheels. 2. Remove the rear brake drums and replace the rear linings. Refer to Workshop Manual (WSM), Section 206-02. WARNING Do not breathe dust or use compressed air to blow dust from storage containers or friction components. Remove dust using government-approved techniques. Friction component dust may be a cancer and lung disease hazard. Exposure to potentially hazardous components may occur if dusts are created during repair of friction components, such as brake pads and clutch discs. Exposure may also cause irritation to skin, eyes and respiratory tract, and may cause allergic reactions and/or may lead to other chronic health effects. If irritation persists, seek medical attention or advice. Failure to follow these instructions may result in serious personal injury. 3. Inspect the rear brake assemblies for damaged, missing and/or improperly seated adjuster plug or parking brake cable. 4. Inspect and clean the lining contact area of the brake drum; machine if necessary. 5. Reinstall the rear brake drums and adjust the lining to drum clearance per WSM, Section 206-02. 6. Thoroughly clean the backside of the rear drum brake backing plate to promote proper adhesion of sealant. 7. Apply Motorcraft(R) Silicone Gasket and Sealant to the backside of the rear drum brake backing plate at the following inter[ace areas (Figure 1): ^ Axle Flange ^ Wheel Cylinder ^ Parking Brake Cable ^ Hold Down Pins NOTE AVOID GETTING SEALANT ON THE BRAKE BLEED SCREW AND BRAKE TUBE NUT. 8. Reinstall the rear wheels and torque lug nuts per Workshop Manual, Section 204-04.

Related entry:

2006 ford escape rear caliper brake adjustmen which way to adjusters tur?, replacing rear drum drakes 2000 chrysler town an country, youtube 2005 chevy 2005 chevy colorado rear brakes replacement, bleeding brakes kia sportage, left brake drum in 2005 chevy equinox diagram, g20 van rear brake inspection and replacement, exploded view of ba fairmont ghia rear brakes, e250 brakes repair, instructions for putting rear brakes on a 1990 silverado 2 wheel drive, exploded view 1957 rear drum brakes,

Mitsubishi Lancer Short Throw Shifter Installation Manual

0

Filed Under (Mitsubishi) by admin on 24-12-2010

download
Mitsubishi Lancer Evolution IV, V, VI, VII, VIII Mitsubishi Lancer FWD 2001 and up Mitsubishi Eclipse 2000 and up Estimated Installation Time: 30-45 Minutes Tools Required: -Philips head screwdriver -8mm wrench -10mm wrench -12mm wrench -8mm, 10mm, and 12mm sockets and ratchet -Bench vise -Grinder 1. Carefully unscrew the stock shift knob. 2. Remove ashtray and screw beneath it. 3. Remove two screws from inside the center console storage compartment. 4. Lift up on the rear section of the center console and unclip it from the front section. 5. Remove plastic screw from the driver’s side of the center console (near the gas pedal). Remove the plastic cover and the pop rivet beneath it. Then remove the two screws at the rear of the console (were hidden by the rearward part of the center console that was removed). 6. Unclip plastic connector at the rear of the console. Remove entire center console. 7. Loosen and remove the bolts at the front and rear of the plastic assembly. Note the order these parts are in as they must be replaced in the same order later in the installation. The front bolt does not need to be completely removed from the plastic assembly, only pulled out enough to allow the top part of the plastic assembly to be lifted off. Now remove the top of the assembly exposing the top of the shifter main pivot ball. 8. Remove the clip on the bottom of the shifter, which connects it to the lower shifter cable. Remove the plastic pivot cup from the lower shifter cable. Also remove the clip attaching the left side shifter cable to the shifter arm. The stock shifter can now be removed. 9. For an Evolution 8 follow this step: using a grinder, shave down the sides of the counterweight / boot support in order to remove the white plastic cup. This in no way damages the stock shifter and it is still usable after the procedure. This enables you to remove the white plastic retaining ring without any cutting.

Related entry:

bushing that connects gear shift to transmission 2007 manual aveo, shift linkage diagram 2000 eclipse, engain diagram for mitsobishi lancer 92,

1995 Ford Thunderbird Spring REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 02-03-2011

download
Removal 1. Raise vehicle on hoist. Refer to Section 00-02. 2. Remove rear wheel and tire assembly. 3. Remove rear stabilizer bar link and bushing link nuts at both ends of rear stabilizer bar (5A772) . Rotate bar up and out of the way. 4. Disconnect parking brake rear cable and conduit (2A635) at rear disc brake caliper (2553) . 5. Install three Rotunda Spring Cages 086-00031 or equivalent to rear spring as follows: a. Install one spring cage without an adjuster link to the inboard side (the innermost “bend” of the rear spring (5560) ). b. Install two more spring cages, with adjusters, at 120 degree angles to the previously installed cage. Spring, Rear 6. Place a transmission jack or suitable stand under the rear suspension arm and bushing (5500) as far outboard as possible. 7. Support the rear wheel knuckle (5A969) assembly by wiring the rear suspension arm and bushing to the body. 8. Remove lower rear shock absorber mounting bolt, washer and nut. 9. NOTE: Rear suspension arm and bushing must not be lowered until pivot bolts are loose. Do not attempt to remove plastic cap on front pivot nut. Loosen both inboard pivot bolts on rear suspension arm and bushing . 10. Remove two bolts and nuts retaining rear suspension arm and bushing to rear wheel knuckle . 11. Lower the rear suspension arm and bushing by lowering jack. Ensure spring cages properly seat on rear spring as rear suspension arm and bushing is dropped. 12. Remove jack, lower rear suspension arm and bushing down fully by hand and remove rear spring with cages in place. 13. Remove rear spring center mounting insulators (5741) , if necessary. 14. If spring cages are to be removed for installation on rear spring , use Coil Spring Compressor D78P-5310-A or equivalent to compress rear spring and remove cages. Rear spring center mounting insulator should be installed on rear spring before installing rear spring in tool to prevent slipping of plates.

Related entry:

2004 Ford Explorer Differential Diagram, blow up diagrams of 2002 ford E150 rear axle, BMW X5 Rear Suspension Diagram, step by step instruction on how to change struts on 1995 740i BMW?, diagram of dodge hatch lock, diagram Caliper slider on vauxhall vectra, 2002 Tahoe rear AC Diagram, replace rear abs sensor 2007 jeep compass, 2008 jeep patriot rear drum breaks disassembly, install knuckle bushing buick,

2003 MITSUBISHI LANCER EVOLUTION VIII SERVICE MANUAL

0

Filed Under (Mitsubishi) by admin on 05-01-2011

download
This manual is designed for use with the 2003 LANCER EVOLUTION VIII Service Manual Volume 2, and Volume 3, and the 2003 LANCER EVOLUTION VIII Body Repair Manual to provide complete service information for the 2003 LANCER EVOLUTION VIII. Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized MITSUBISHI dealer. MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B, Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of the SRS or any SRS-related component. • •

Related entry:

what type of ac is in a 2004 mitsubishi lancer, mitsubishi 4m50 repair manual pdf, 4g13 carb boost, mitsubishi lancer glxi 1996 owners manual pdf, mitsubishi lancer oz rallye 2004 service manual, mitsubishi space star manual free download, p1590on mistibshi, mitsubishi lancer 2007 valve body manual, recharge ac 2008 lancer, mitsubishi 4d32 repair manual,

2004 Ford F-150 Rear Axle Differential Cover Axle Shaft Oil Seal and Rear Wheel Bearing REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 28-02-2011

download
1. With the vehicle in NEUTRAL, position on a hoist. For additional information, refer to Section 100-00. 2. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-00. 3. Remove the parts in the order indicated in the following illustration and table. 4. To install, reverse the removal procedure. 5. Fill the axle with the specified quantity of the specified lubricant. For additional information, refer to the Specifications in this section. Item 2: Rear Disc Brake Caliper Removal Note 1. CAUTION: Do not allow the caliper to hang from the brake hose. Provide a suitable support. Position the rear disc brake caliper aside. For additional information, refer to Section 206-00. Item 7: Differential Pinion Shaft Removal Note 1. Move the differential pinion shaft out far enough to remove the U-washers. Replace the shaft and install the lock bolt finger tight when U-washers are removed. Item 8: U-washer Removal Note 1. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers. 1. Push the axle shafts inboard. 2. Remove the U-washers. Item 10 and 11: Wheel Bearing Oil Seal and Axle Shaft Bearing Removal Note 1. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 8.8 inch rear axle, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. 2. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 9.75 inch and the 10.25 inch rear axles, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. Item 11: Axle Shaft Bearing Installation Note 1. For the 8.8 inch and the 9.75 inch rear axles, use the special tools to install the rear axle wheel bearing. 2. For the 10.25 inch rear axle, use the special tools shown to install the rear axle wheel bearing. Item 10: Wheel Bearing Oil Seal Installation Note 1. Use the special tools shown to install the rear wheel bearing oil seal. Item 8: U-washer Installation Note 1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers. 1. Position the two U-washers on the button end of the axle shafts. 2. Pull the axle shafts outward.

Related entry:

2004 ford explorer rear differential diagram, tourch on rear wheel bearing on a 2010 chevy impala, 2004 expedition right axle tube seals, 2004 ford escape rear gears, balance shaft seal for 2004 honda acccord 4 cylinder schematic, how to remove rear axle shaft of mitsubishi strada triton, 2008 chevy silverado cv axle nut size, 2006 suzuki forenza front wheel drive axle diagram, 2007 acadia rear blower removal, back axle ford transit,