2002 toyota rav4 oxygen sensor diagram


You are searching repair manual in PDF format about 2002 toyota rav4 oxygen sensor diagram use another keyword for search another post or files



  2002 toyota rav4 oxygen sensor diagram Direct Download speed 5787 Kb/s

  2002 toyota rav4 oxygen sensor diagram Full Version speed 6767 Kb/s




1995 Ford Mustang Camshaft Position (CMP) Sensor Removal Installation

0

Filed Under (Ford) by admin on 08-02-2011

download
1. Disconnect battery ground cable (14301) . 2. Disconnect fuel charging wiring (9D930) from distributor stator (12A112) (camshaft position sensor). 3. Remove stator camshaft position sensor retaining screws and distributor stator (camshaft position sensor) from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the engine front cover (6019) , proceed with Removal Step 5. If camshaft position sensor housing is not being removed, proceed to Installation Step 6. 5. CAUTION: Before proceeding with this procedure, set cylinder No. 1 to 26 degrees After Top Dead Center (ATDC) of the compression stroke. Then note the position of the stator (camshaft position sensor) electrical connector. The installation procedure requires that the connector be located in the same position. Remove retaining bolt and hold-down clamp (12270) . 6. NOTE: The oil pump intermediate shaft (6A618) should be removed with the camshaft position sensor housing. Remove camshaft position sensor housing from engine front cover . Installation 1. CAUTION: If the replacement distributor stator (camshaft position sensor) does not contain a plastic locator cover tool, a special service tool such as Syncro Positioning Tool T89P-12200-A must be obtained prior to installation of the replacement distributor stator (camshaft position sensor). Failure to follow this procedure will result in improper stator (camshaft position sensor) alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. If the plastic locator cover tool is not attached to the replacement distributor stator (camshaft position sensor), attach Syncro Positioning Tool T89P-12200-A as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. The cover tool should be square and in contact with entire top surface of camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 30 degrees counterclockwise from the front face of the cylinder block (6010) . This step will locate stator (camshaft position sensor) electrical connector in the pre-removal position. 4. Install hold-down clamp and retaining bolt and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove Syncro Positioning Tool T89P-12200-A. 6. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install distributor stator (camshaft position sensor) and retaining screws. Tighten screws to 2.5-3.5 Nm (22-31 lb-in). 7. Connect fuel charging wiring connector to distributor stator (camshaft position sensor). 8. Connect battery ground cable .

Related entry:

2003 Envoywiring connector to alternator pigtail, torque procedure of the bearing caps on saab 2 5 v6, locate camshaft sensor on dodge grand caravan 2003, toyota townace 1997 7k eng set timing, replacing the knock sensor on 2004 ford freestar, how do you fix speedometer on a 1999 vw cabrio, sonata 2 5 cam shaft sensor replacement, BMW X5 HEIGHT SENSOR, speedosensor isuzu 2 4 KB, step by step camshaft removal and rebuild on a vauxhall z18 xer,

1998 Ford Windstar Camshaft Position (CMP) Sensor REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 17-02-2011

download
CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126) , set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires the connector be located in the same position. Removal 1. Disconnect battery ground cable (14301). Refer to Section 14-01. 2. Disconnect fuel charging wiring connector from camshaft position sensor. 3. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to Step 6 of the installation procedures. 5. Remove hold-down clamp (12270) (bolt and washer assembly). 6. NOTE: Remove the oil pump intermediate shaft (6A618) with the camshaft position sensor housing. Remove camshaft position sensor housing from cylinder block. Installation 1. CAUTION: If the replacement camshaft position sensor housing does not contain a plastic locator cover tool, a special service tool must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the ignition fuel system being out of time with the engine, possibly causing engine damage. NOTE: For 3.0L engines, use Syncro Positioning Tool 303-589. For 3.8L engines, use Syncro Positioning Tool 303-562 (T96T-12200-A). If the plastic locator cover tool is not attached to the replacement camshaft position sensor housing, attach syncro positioning tool as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. Install camshaft position sensor housing so drive gear engagement occurs when arrow on syncro positioning tool is pointed approximately as shown in the illustrations. This step will locate camshaft position sensor electrical connector in the pre-removal position. 4. Install hold-down clamp (washer and bolt assembly) and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove syncro positioning tool. 6. CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor and retaining screws. On 3.0L engine, tighten screws to 2.5-3.5 Nm (23-30 lb-in). On 3.8L engine, tighten screws to 4.5-7 Nm (40-61 lb-in). 7. Connect fuel charging wiring connector to camshaft position sensor. 8. Connect battery ground cable. Refer to Section 14-01. Camshaft Position Sensor—3.0L Engine

Related entry:

6a12 mivecmd temperature coolant sensor max temp degrees, where is the torque sensor located on a 2009 chevy malibu, 1998 gmc safari coolant thermostat, 2009 chevy malibu torque sensor assembly, 2012 sonic o2 sensor removal man, cost of repairing torque sensor assembly on 2009 cheverolet malibu, GM Tool - J 38491, sonic o2 sensor removal,

2003-2006 Chevrolet Express Antilock Brake (ABS) Activation At Low Speeds (Clean Wheel Speed Sensor Mounting Surface)

0

Filed Under (Chevrolet) by admin on 25-01-2011

download
Condition Some customers may comment on ABS activation at low speeds, usually below 8 km/h (5 mph). Upon investigation, the technician will find no DTCs set. Cause The cause of this condition may be an increased air gap between the wheel speed sensor and the hub reluctor ring due to rust and debris built up on the sensor mounting surface. Correction Measure AC voltage and clean the wheel speed sensor mounting surfaces. 1. 2. 3. 4. Raise and support the vehicle. Disconnect both the front wheel speed sensor connectors at the frame and harness. Place a Digital Volt Meter (DVM) across the terminals of each wheel speed sensor connector. Rotate the wheel clockwise approximately one revolution per second. The minimum reading should be at least 350 ACmV’s. If the reading is less than 350 ACmV’s, remove the wheel speed sensor. 5. Plug the wheel speed sensor bore in order to prevent debris from falling into the hub during service. 6. Clean the wheel speed sensor mounting surface using a wire brush, sand paper, emery cloth, scotch brite, or other suitable material. Be sure to thoroughly clean the wheel speed sensor surface. There should be no rust or corrosion. 7. Check the sensor head to determine if it has been warped/distorted due to the corrosion build up or other causes. Check the mounting surface on the sensor head for flatness by placing it on the edge of a metal machinists scale or other suitable straight edge to measure the flatness. Check the sensor for flatness in multiple (minimum 3) positions/directions. If the sensor head is distorted, replace the sensor. 8. Apply (spray) two thin coats of the specified rust penetrating lubricant (corrosion inhibitor) to the complete sensor mounting surface on the bearing hub. Allow to dry for 3-5 minutes between coats. Use ONLY Rust Penetrating Lubricant, P/N 89022217 (in Canada, P/N 89022218). 9. When the corrosion inhibitor is dry to the touch (about 10 minutes), apply a thin layer of bearing grease to the hub surface and sensor O-ring prior to sensor installation. Use ONLY Wheel Bearing Lubricant, P/N 01051344 (in Canada, P/N 993037). 10.Install either the original sensor or a new one in the hub. Ensure that the sensor is seated flush against the hub. Refer to the applicable Wheel Speed Sensor Replacement procedure in the ABS sub-section of the Service Manual. 11.Place the DVM across the sensor terminals and recheck the voltage while rotating the wheel. The voltage should now read at least 350 ACmV’s.

Related entry:

mazda 3 speed sensor turbine, remove wiring clip on 2002 RAV 4 Speed sensor, replace o2 sensor on 2007 linconl mkx, replacing crank sensor in 2004 express, replacing wheel speed sensor 2006 uplander, speed sensor corlla 05, unhook abs sensor from rotor 2006 colorado, vehicle speed sensor location on a corsa b light, wher is speed sensor located at on a 2010 cobalt/ diagram, where is the vehicle speed sensor for a 2005 kia sorento rear wheel drive located,

2002 Buick Rendezvous Heated Oxygen Sensor (HO2S) 1 Replacement

0

Filed Under (Buick) by admin on 01-11-2010

download
REMOVAL PROCEDURE NOTE: The Heated Oxygen Sensor (HO2S) and the Oxygen Sensor use a permanently attached pigtail and connector. Do not remove this pigtail from the Heated Oxygen Sensor. Damage or the removal of the pigtail or the connector could affect the proper operation of the sensor. Take care when handling the HO2S and the O2S. keep the in-line electrical connector and the louvered end free of grease, dirt, or other contaminants. Also avoid using cleaning solvents of any type. Do not drop the HO2S or the O2S. Do not roughly handle the HO2S or the O2S. 1. Disconnect the electrical connector. 2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle. NOTE: The use of excessive force may damage the threads in the exhaust manifold/pipe. IMPORTANT: If the engine temperature is not above 48° (120° ), the C F oxygen sensor will be difficult to remove. 3. Use the J 39194-B in order to remove the heated oxygen sensor (HO2S). INSTALLATION PROCEDURE NOTE: Refer to Fastener Notice in Service Precautions. A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

Related entry:

2007 rav4 oxygen sensor locations,

TOYOTA RAV4 ELECTRICAL WIRING DIAGRAM

0

Filed Under (Toyota) by admin on 28-09-2009

ELECTRICAL WIRING DIAGRAM
This Service Bulletin is to inform you of the Electrical Wiring Diagram for RAV4 equipped with 1CD-
FTV engine.RELAY LOCATIONS ELECTRICAL WIRING ROUTING OVERALL ELECTRICAL WIRING DIAGRAM CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS

download

Related entry:

manual book suzuki apv, download free service manual velociti 1 6i 2007, 2010 town&country window wiring diagram, 1996 riviera interval wiper wiring diagram, wiring diagram for 1971 jeepster commando, underbody pictures of 2002 chevy trailblazer diagrams, 1987 chevy camaro power steering wiring diagram free dowload, 2006 chevrolet silverado blower motor wiring diagram, suzuki alto rear wiper diagram, 69 chevy c10 truck horn relay wiring diagram,