2003 INFINITI G35 FUSE BOX DIGRAM
You are searching repair manual in PDF format about 2003 INFINITI G35 FUSE BOX DIGRAM use another keyword for search another post or files
2003 INFINITI G35 FUSE BOX DIGRAM Direct Download speed 5787 Kb/s
2003 INFINITI G35 FUSE BOX DIGRAM Full Version speed 6767 Kb/s
Filed Under (Honda) by admin on 27-05-2010
UNDER-DASH FUSE/RELAY BOX NOTE: Under-dash fuse/relay box is located under driver’s side of instrument panel. See Fig. 1 or Fig. 2 . Fig. 2: Locating Under-Dash Fuse/Relay Box (1998-2000) Fig. 3: Identifying Under-Dash Fuse/Relay Box Components (1996-2000) Fig. 4: Under-Dash Fuse/Relay Box Legend (1996-2000 – 1 Of 2) UNDER-HOOD ABS FUSE/RELAY BOX NOTE: Under-hood ABS fuse/relay box is located in passenger’s side of engine compartment, on strut tower. See Fig. 6 . Fig. 6: Locating Engine Compartment Fuse/Relay Boxes (1996-2000) Fig. 7: Identifying Under-Hood ABS Fuse/Relay Box Components & Legend (1996-2000)
Filed Under (Ford) by admin on 11-05-2010
Some 1999-2004 Navigator, 2002-2003 Blackwood, 2003-2005 Aviator, 2003-2004 Marauder and 2003-2004 Mustang vehicles built before 12/19/2004 equipped with 4.6L 4V/5.4 4V engine may exhibit a runs rough, lacks power, and engine misfire, prompted by a MIL light and DTC codes P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, and P0316. ACTION Diagnose engine for engine misfire concern. If diagnostics determine an engine misfire which is characterized by leakage through exhaust valve(s), only replace the affected cylinder head(s). SERVICE PROCEDURE
Filed Under (Nissan) by admin on 08-09-2009
service, repair and maintenance information for 2003-2008 Nissan 350Z & Infiniti G35 cars.Includes:
General Information, Routine Maintenance & Tune-Up, Engine & Engine Overhaul, Driveability & Emission Controls, Trouble Codes & Diagnostics, Fuel System, Chassis Electrical, Drive, Suspension & Steering, Brakes, Body and full Glossary.
Filed Under (Infiniti) by admin on 18-05-2010
CAUTION: ^ Clean dust on caliper and brake pad with a vacuum dust collector. Do not blow with compressed air. ^ While brake pad and cylinder body are separated, piston may suddenly jump out, so do not depress brake pedal. ^ It is not necessary to remove bolts on torque member and brake hose except for disassembly or replacement of caliper assembly. In this case, hang cylinder body with a wire so that brake hose is not under tension. ^ Do not damage piston boot. ^ If any shim is subject to serious corrosion, replace it with a new one. ^ Always replace shims and shim covers as a set when replacing brake pads. ^ Keep rotor clean of brake fluid.
Filed Under (Infiniti) by admin on 04-07-2010
REMOVAL 1. Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. 2. Remove engine cover. Refer to “INTAKE MANIFOLD COLLECTOR”. 3. Remove air cleaner assembly, air hose and air duct. Refer to “AIR CLEANER AND AIR DUCT”. 4. Remove mounting bolt from high-pressure flexible hose bracket. 5. Disconnect one-touch joint between high-pressure flexible hose and condenser. a. Set a disconnector (92530-89912) on A/C piping. b. Slide a disconnector upward until it clicks. c. Slide A/C piping upward and disconnect it. CAUTION: Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air. 6. Remove mounting nuts from high-pressure flexible hose, and then remove high-pressure flexible hose. CAUTION: Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air. INSTALLATION Installation is basically the reverse order of removal. CAUTION: Replace O-ring of high-pressure flexible hose with a new one, then apply compressor oil to it when installing it.