2003 ford 4.6 liter triton head gasket replacment
You are searching repair manual in PDF format about 2003 ford 4.6 liter triton head gasket replacment use another keyword for search another post or files
2003 ford 4.6 liter triton head gasket replacment Direct Download speed 5787 Kb/s
2003 ford 4.6 liter triton head gasket replacment Full Version speed 6767 Kb/s
Filed Under (Mitsubishi) by admin on 31-05-2010
Fig. 82: Removing/Installing Cylinder Head Gasket REMOVAL SERVICE POINT << A >> CYLINDER HEAD ASSEMBLY REMOVAL Use special tool MD998051 to loosen each bolt two or three steps in the order shown in the illustration. Fig. 83: Removing Cylinder Head Fig. 84: Identifying Cylinder Head Gasket On Cylinder Block With Identification Mark At Front Top INSTALLATION SERVICE POINTS >>A<< CYLINDER HEAD GASKET INSTALLATION 1. Degrease the cylinder head and cylinder block gasket mounting surfaces. 2. Make sure that the gasket has the proper identification mark for the engine.
Filed Under (Hyundai) by admin on 04-05-2011
1. 2. 3. 4. 5. Drain the coolant and disconnect the upper radiator hose. Remove the breather hose (between the air cleaner and the rocker cover). Remove the air-intake hose. Remove the vacuum hose, fuel hose and coolant hose. Remove the cables from the spark plugs. The cables should be removed by holding the boot portion. Remove the ignition coil. Remove the surge tank. Remove the intake manifold. Remove the heat protector and exhaust manifold assembly Remove the coolant pump pulley and the crankshaft pulley. Remove the timing belt cover. 6. 7. 8. 9. 10. 11. Zoom Sized for Print 12. Move the timing belt tensioner pulley toward the coolant pump and temporarily secure it. 13. Remove the timing belt. 14. Remove the rocker cover. 15. Remove the cylinder head assembly. The cylinder head bolts should be removed using Special Tool, Cylinder Head Bolt Wrench (09221-21000), in the sequence as shown in the illustration. 16. Remove the gasket pieces from the cylinder block top surface and cylinder head bottom surface. NOTE: 1. Make sure that the gasket pieces do not fall in to the engine. INSPECTION 1. Check the cylinder head for cracks, damage and coolant leakage. 2. Remove scale, sealing compound and carbon deposits completely. After cleaning oil passages, apply compressed air to make certain that the passages are not clogged. 3. Check the cylinder head surface for flatness using a straight edge in the direction of A, B, …as shown. If flatness exceeds service limit in any direction, replace the cylinder head, or lightly machine the cylinder head surface. Cylinder head flatness Standard value: Less than 0.03 mm (0.0012 inch) Limit: 0.08 mm (0.0031 inch) REASSEMBLY 1. Clean all gasket surfaces of the cylinder block and the cylinder head. 2. Install a new cylinder head gasket onto the cylinder head assembly. Do not apply sealant to the gasket and do not reuse the old cylinder head gasket.
Filed Under (Toyota) by admin on 05-08-2010
1. Install cylinder head. A. Place cylinder head on cylinder block. (a) Place a new cylinder head gasket on the cylinder block. CAUTION: Be careful of the installation direction. (b) Place the cylinder head on the cylinder head gasket. B. Install cylinder head bolts. NOTE: The cylinder head bolts are tightened in 2 progressive steps (steps (b) and (d)). If any cylinder head bolt is broken or deformed, replace it. (a) Apply a light coat of engine oil on the threads and under the heads of the cylinder head bolts. Cylinder Head Installation Install and uniformly tighten the 10 cylinder head bolts and plate washers in several passes, in the sequence shown. Torque: 49 Nm (36 ft. lbs.) If any one of the cylinder head bolts does not meet the torque specification, replace the cylinder head bolt. (c) Mark the front of the cylinder head bolt head with paint. (d) Retighten the cylinder head bolts 90° in the numerical order shown. (e) Check that the painted mark is now at a 90° angle to the front. Install the 2 bolts holding the water bypass pipe to the cylinder head. Torque to 19 Nm (14 ft. lbs.) (g) Connect the camshaft position sensor connector. 2. Install spark plug tubes. (a) Clean the cylinder head tube holes of any residual adhesive, oil or foreign particles. Remove any oil with kerosene or gasoline. (b) Screw the threads of the spark plug tube coated with adhesive into the cylinder head.
Filed Under (Ford) by admin on 11-05-2010
Some 1999-2004 Navigator, 2002-2003 Blackwood, 2003-2005 Aviator, 2003-2004 Marauder and 2003-2004 Mustang vehicles built before 12/19/2004 equipped with 4.6L 4V/5.4 4V engine may exhibit a runs rough, lacks power, and engine misfire, prompted by a MIL light and DTC codes P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, and P0316. ACTION Diagnose engine for engine misfire concern. If diagnostics determine an engine misfire which is characterized by leakage through exhaust valve(s), only replace the affected cylinder head(s). SERVICE PROCEDURE
Filed Under (Ford, Lincoln) by admin on 17-10-2009
The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford Escape / Mercury Mariner 2007-2009 Ford Expedition / Lincoln Navigator 2006-2009 Ford Explorer / Lincoln Aviator / Mercury Mountaineer 2007-2008 Ford F150, F250, and F350 / Lincoln Mark LT
2009 Ford Flex 2008-2009 Ford Focus 2006-2007 Ford Freestar / Mercury Monterey 2008-2009 Ford Fusion / Lincoln MKZ / Mercury Milan 2007-2009 Ford Mustang 2007-2009 Ford Ranger 2008-2009 Ford Taurus / Mercury Sable
1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard). 2. Turn the ignition switch to OFF then press and release the brake pedal. 3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds. 4. Press and release the brake pedal