2003 hyundai sonata timing marks diagram


You are searching repair manual in PDF format about 2003 hyundai sonata timing marks diagram use another keyword for search another post or files



  2003 hyundai sonata timing marks diagram Direct Download speed 5787 Kb/s

  2003 hyundai sonata timing marks diagram Full Version speed 6767 Kb/s




2003 TOYOTA TACOMA TIMING BELT INSTALLATION REMOVAL

0

Filed Under (Toyota) by admin on 13-01-2011

download
NOTICE: Always turn the crankshaft clockwise. (c) Check that the timing marks of the camshaft timing pul- leys and No.3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°). (d) Remove the crankshaft pulley bolt. IF REUSING TIMING BELT, CHECK INSTALLATION MARKS ON TIMING BELT Check that there are 3 installation marks and front mark on the timing belt. If the installation and front marks have disappeared, before re- moving the timing belt, place 3 new installation marks on the timing belt to match the timing marks of the timing pulleys, and place a new front mark on the timing belt. 18. 19. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt ten- sioner and dust boot. 20. REMOVE TIMING BELT 21. (a) REMOVE RH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 22. (a) REMOVE LH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 23. REMOVE NO.2 IDLER PULLEY Remove the bolt and idler pulley. 24. REMOVE NO.1 IDLER PULLEY Using a 10 mm hexagon wrench, remove the pivot bolt, idler pulley and plate washer. 25. REMOVE CRANKSHAFT TIMING PULLEY Remove the timing pulley. HINT: If the pulley cannot be removed by hand, use SST and a service bolt to remove the timing pulley. SST 09950–50011 (09951–05010, 09952–05010, 09953–05020, 09954–05011)

Related entry:

2003 opel vivaro 1 9 dci service manual pdf, 2005 mazda 6 2 3l engine timing marks, 1azfe removing crank pulley, pdf file on how to do timing on a kj2 laser, YouTube 07 mazda cx 7 setting timing chain, 2004 Chrysler Pacifica Timing Marks, 2007 Suzuki Forenza Timing Marks, youtube setting timing chain on 07 mazda cx 7, timing marks 2 7 dodge strstus 2001/, mazda wl timing gears,

1999 Hyundai Tiburon HYUNDAI’ ’1.8L & 2.0L 4-Cylinder – 1996-04 (Except Sonata & 2004 Elantra) TIMING BELT REMOVAL & INSTALLATION

0

Filed Under (Hyundai) by admin on 06-04-2010

download
TIMING BELT Removal
1. Remove all drive belts and drive pulleys from crankshaft and water pump. Remove generator bolt, if necessary. Remove crankshaft pulley and water pump pulley. 2. Remove timing belt covers and gaskets, noting bolt lengths and locations. DO NOT rotate engine counterclockwise, as viewed from timing belt side of engine. Remove timing belt tensioner pulley. 3. Rotate engine clockwise to align all timing marks so No. 1 cylinder is at TDC of compression stroke. See Fig. 1 . If reusing belt, place mark on timing belt to indicate direction of belt rotation. Remove belt. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.

Related entry:

a/c tensioner 2002 hyandai elantra, how to replace the a/c tenision Pulley on 2001 hyundia elantra, 2002 hyundai elantra new tensioner, hyundai atos timing marks, how to replace 2003 tiburon ac compressor, how many belts in a 2002 hyundai elantra, haynes 1999 hyundai tiburon manual free download, 06 elantra ac tencion pully, 2002 hyundai elantra fixing ac where is ac, 2002 hyandai elantra a/c tensioner diagram,

1996 Chevrolet Monte Carlo Camshaft Timing COMPLETE CAM TIMING PROCEDURE

0

Filed Under (Chevrolet) by admin on 10-08-2010

download
T] EXHAUST CAMSHAFT (RIGHT) T| INTAKE CAMSHAFT (RIGHT) T] SECONDARY TIMING BELT IDLER PULLEYS T) INTAKE CAMSHAFT (LEFT) 7] EXHAUST CAMSHAFT (LEFT) T] COOLANT PUMP T] INTERMEDIATE SHAFT BELT SPROCKET T] SERPENTINE BELT TENSIONER T| SECONDARY TIMING BELT TENSIONER PULLEY ??] GENERATOR ??] SECONDARY TIMING BELT TENSIONER ?2? SECONDARY TIMING BELT NOTE: START AT #7 AND INSTALL COUNTERCLOCIOMBE A LOCATION OF TIMING MARKS WITH CAM HOLD DOWN TOOLS J 38813 INSTALLED B FRONT COVER TIMING MARK C LOCATION OF TIMINS MARKS WITH DRIVE BELT IN- STALLED D LOCATION WHERE CAM HOLD DOWN TOOLS ARE INSTALLED RH EXHAUST CAMSHAFT SPROCKET RH INTAKE CAMSHAFT SPROCKET LH INTAKE CAMSHAFT SPROCKET LH EXHAUST CAMSHAFT SPROCKET PERMANENT MARKS PAINTED DOTS REMOVE PREVIOUS MARKS IF TIMING IS BEINS CHANGED AND MARK AGAIN IN THESE LOCATIONS TORSIONAL DAMPER INTERMEDIATE SHAFT SPROCKET NOTE: THIS TDC #1 EXHAUST. INTtRMEDlATE »HAFT BELT sprocket twno mark» at » o’clock (powtmo towards drain notch) NOTE : GM does not provide a timing mark diagram for belt installation without using the special tool(s) listed below. TOOLS REQUIRED: A J 38613 CamHold Down Tool A J 38614 Cam Sprocket Holding Tool NOTICE: If only one (1) bank is to be timed, make sure bank to bank earn timing relationship is one (1) revolution apart. Timing flats should be 180 degrees opposite (right bank versus left bank) when finally timed. 1. Remove all spark plugs. 2. Remove all camshaft sprockets. IMPORTANT: Remove oil from cam hold down tool bolt hole in carrier before installing and tightening bolt. 3. Rotate camshaft flats “up” and install J 38613. Tighten cam hold down tool bolt to 30 Nm (22 lb. ft). 4. Install all camshaft sprockets. 5. Timing belt by routing it around the idlers and sprockets. DO NOT bend, kink, or pry on belt as damage may occur. A. Start at intermediate cam sprocket and work counterclockwise. B. Make sure the belt is installed in direction of rotation. C. Engage teeth into all sprockets, place rubber hose behind belt at intermediate sprocket and accumulate slack at tensioner location. 6. Tensioner pulley to mounting base. A Use flat magnet, tape or cup plug to hold pivot tube in pulley during this step. Otherwise, pivot tube may fall out. A After starting pivot bolt, rotate arm counterclockwise to position square lug at 6 o’clock

Related entry:

4 3 Vortec Timing Procedure, bmw n63 timing procedure, diagram gor camshalf setting on 1995 corolla, 4zze engine timing marks, how to fix timing chain on mercedes benz c220, pic of cam lobe top dead center on a 2004 suzuki forienza, 1azfe cam timing, The senses in the transmission of a Lincoln MK ex 08, how to replace camshaft on ford expedition 2005, how to reset the tdc on a 2000 audi quattro v6 2 4 30 valve engine,

2002 Hyundai Sonata GLS TIMING & COUNTERBALANCE SHAFT BELTS REMOVAL & INSTALLATION

0

Filed Under (Hyundai) by admin on 21-11-2010

download
MANUFACTURER’S SUGGESTED SCHEDULED MAINTENANCE The manufacturer recommends the belt be replaced every 60,000 miles, except in California. In California, inspect timing belt at 60,000 miles, and replace as necessary. REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING & COUNTERBALANCE SHAFT BELTS Removal CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate direction of rotation before removing. 1. Remove drive belts and drive pulleys from crankshaft and water pump. Remove timing belt covers. To align timing marks, rotate engine clockwise so No. 1 cylinder is at TDC of compression stroke. Ensure camshaft sprocket timing marks align with upper surface of rocker cover. Dowel pin of camshaft sprocket should be pointing upward. See Fig. 1 and Fig. 2 . 2. Remove timing belt auto tensioner. If reusing timing belt, place mark on timing belt to indicate direction of belt rotation. Remove timing belt. Remove camshaft sprockets. 3. Remove plug at left side of block and insert a screwdriver to hold left counterbalance shaft in position. Screwdriver will have to be inserted at least 2.36″ (60 mm). Remove oil pump sprocket nut and sprocket. See Fig. 2 . 4. Loosen right counterbalance shaft sprocket mounting bolt. Remove tensioner “B” and timing belt “B”. See Fig. 2 . Remove crankshaft sprocket “B” from crankshaft.

1996 Mitsubishi Eclipse GS-T TIMING BELT & BALANCE SHAFT BELT Removal

0

Filed Under (Mitsubishi) by admin on 18-01-2011

download
1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. CAUTION: DO NOT rotate crankshaft counterclockwise. Ensure timing marks are aligned. If reusing timing belts, mark timing belts for direction of rotation. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. NOTE: Camshaft sprocket dowel pins will be in 12 o’clock position when timing marks are correctly aligned. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B”.

Related entry:

04 optra 2 0 l dtec timing marks, ecotec balance shaft timing marks, 03 p/t crucer valance shaft marks, how to set correct timing for mitsubishi lancer 4G15A, how to set timing marks using obx timing sprockets on mitsubishi eclipse 2 0 dohc, mitsubishi 4d56 balance shaft belt timing, mitsubishi 4d56 turning engine counterclockwise, mitsubishi triton timing belt interval, qg16 timing marks, remove Ford xh longreach ute Timing Chain,