2003 hyundai tiburon clutch fork diagram


You are searching repair manual in PDF format about 2003 hyundai tiburon clutch fork diagram use another keyword for search another post or files



  2003 hyundai tiburon clutch fork diagram Direct Download speed 5787 Kb/s

  2003 hyundai tiburon clutch fork diagram Full Version speed 6767 Kb/s




2005–2006 Toyota Tacoma CLUTCH PEDAL SQUEAK NOISE

0

Filed Under (Toyota) by admin on 04-06-2011

download
Some customers may complain about a “squeak” or “creak” noise when depressing or releasing the clutch pedal. The clutch master cylinder clevis assembly has been improved to eliminate this condition. Repair Procedure 1. Record all radio presets before starting. 2. Disconnect the negative (–) battery terminal cable. 3. Remove the clutch pedal sub–assembly. A. Remove the front door opening trim LH (scuff plate). B. Remove the cowl side trim board. C. Remove the instrument panel finish panel lower No. 1. D. Remove the driver’s side Junction Block. E. Remove the turnover (compression) spring. F. Remove the bolt attached to the instrument panel reinforcement assembly. G. Remove the clutch pedal sub–assembly. a. Remove the bolt and nut. b. Remove the clutch pedal from the clutch pedal support. 4. Remove the clutch pedal spring holder from the clutch pedal support. 5. Remove the clutch pedal pad. 6. Remove the two (2) clutch pedal bushes from the clutch pedal. 7. Remove the clutch pedal shaft collar. 8. Using needle–nose pliers, remove the No. 1 cushion from the clutch pedal. 9. Install the clutch pedal No. 1 cushion on the NEW clutch pedal sub–assembly. NOTE: Install parts on the NEW clutch pedal sub–assembly BEFORE installing in the vehicle. 10. Install the clutch pedal shaft collar. A. Apply MP grease to the clutch pedal shaft collar. B. Install the clutch pedal shaft collar onto the clutch pedal. 11. Install the clutch pedal bushes. A. Apply MP grease to the two (2) NEW bushes. B. Install the two (2) bushes onto the clutch pedal. 12. Install the clutch pedal pad. 13. Install the clutch pedal spring holder. A. Apply MP grease to the contact surface of the clutch pedal spring holder. B. Install the clutch pedal spring holder. 14. Remove the clevis sub–assembly. A. Measure length “A” of the clutch master cylinder. a. Measure length “A” between the lock nut and the thread end with a ruler. b. Record length “A”. B. Remove the clevis sub–assembly from the master cylinder. a. Loosen the lock nut. b. Rotate and remove the clevis sub–assembly. 15. Install the NEW clevis sub–assembly. A. Rotate the lock nut to match length “A”. B. Rotate and install the NEW clevis sub–assembly to contact the lock nut. C. Tighten the lock nut and torque to specification. Torque: 11.8 NSm (120 kgfScm, 8.7 ftSlbf) D. Apply MP grease to the ball end of the clevis sub–assembly where it will contact the clutch pedal. 16. Install the NEW clutch pedal sub–assembly. A. Install the clutch pedal onto the clutch support with the bolt and nut. Torque: 34 NSm (347 kgfScm, 25 ftSlbf) HINT: Install the bolt from the left side of the vehicle. B. Apply MP grease to the clutch pedal sub–assembly where the clevis sub–assembly contacts the clutch pedal. NOTE: Failure to apply grease to the clevis and clutch pedal sub–assemblies could cause the noise to return. C. Tighten the bolt to the instrument panel reinforcement assembly. Torque: 8 NSm (82 kgfScm, 6 ftSlbf) 17. Install the turnover (compression) spring. A. Apply MP grease to the contact surface of the spring holder, clutch pedal, and spring. B. Install the spring onto the clutch pedal and spring holder.

Related entry:

1994 mazda b3000 how to replace clutch and slave free download, ford mondeo 2003 clutch cable, 2005 kia sorento bleed the cluch, 97 jetta clutch cable removal, how to change clutch disk in mazda 323, clutch adjustment on 1997 kia sephia, a/c clutch 2007 escape tests good has power, how to install ac clutch on 2002 ford f150 4 6, changing clutch on 2006 kia sorento, 2006 fiesta clutch removal,

2000 Ford F-Super Duty 250-550 Clutch Master Cylinder and Reservoir REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 08-03-2011

download
Removal CAUTION: Remove the entire clutch hydraulic system from the vehicle as an assembly when installing a new clutch master cylinder assembly (7C522). 1. Disconnect the clutch hydraulic tube from the dash clip. 2. Raise and support the vehicle. For additional information, refer to Section 100-02. 3. Unlock and remove the slave cylinder (7A564) from the transmission. Compress and twist the slave cylinder to unlock it from the transmission. 4. Disconnect the clutch hydraulic tube from the floor pan clip. Position the slave cylinder and hydraulic tube forward below the left engine bank. This will make it easier to unlock the clutch master cylinder from the clutch pedal and support bracket (7B633) by reducing tension on the hydraulic tube. 5. Lower the vehicle. 6. WARNING: The clutch pedal is under spring tension. Unlock the push rod bushing retaining clips and separate the clutch master cylinder push rod from the clutch pedal. 7. Remove and discard the push rod bushing (7526). 8. Remove the switch cover, and remove the clutch pedal position switch (7C534) from the clutch master cylinder push rod. 9. Separate the power distribution box from the bracket to gain access to the clutch master cylinder. 10. Unlock and remove the clutch master cylinder from the clutch pedal and support bracket. Compress and twist the clutch master cylinder clockwise 45 degrees to unlock it from the clutch pedal and support bracket. 11. Remove the clutch hydraulic reservoir from the wiring tray and separate the clutch hydraulic tube from the brake master cylinder assembly. Position the clutch hydraulic reservoir aside. 12. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, wash the surface with water immediately. Remove the clutch hydraulic system from the vehicle. 13. Clean the clutch hydraulic system components to prevent contaminants from entering the hydraulic system. 14. CAUTION: Place a suitable container under the clutch master cylinder. Disconnect the hydraulic tube from the clutch master cylinder. 1. Using a 3/32-inch punch and a hammer, drive out the roll pin, and discard it. 2. Disconnect the hydraulic tube from the clutch master cylinder.

Related entry:

1995 eclipse clutch slave cylinder diagram, 2000 ford f650 clutch slave master cylinder, 2002 chevy cavaleir slave cylinder step by step installation instructions, clutch slave cylinder repair on 2004 saturn vue, 2004 cavalier transmission bleed screw, youtube how to replace hydraulic line from clutch master cilider on 2002 honda civic, how to remove pin on slave cylinder on 92 chevy p/u 1500, HOW TO REMOVE CONCENTRIC SLAVE 3 8 2006 ECLIPSE, HOW TO GREASE CLUTCH ON 2004 KIA SORENTO, how to bleed slave cylinder on cavalier,

2001 Ford F-150 Clutch Master Cylinder/ Reservoir REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 08-03-2011

download
Removal NOTE: When replacing clutch master cylinder (7A543), remove tubing from vehicle for bench bleeding procedure. 1. Disconnect the clutch master cylinder push rod from the clutch and brake pedal pivot shaft lever. 2. Disconnect the clutch pedal position switch (CPP) (11A152). 3. Remove the pushpins. 4. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking, or towing an air suspension vehicle. This can be accomplished by turning off the rh kick panel area. Failure to inflation of deflation of the air springs which may result in shifting of the vehicle during these operations. Raise and support the vehicle. For additional information, refer to Section 100-02. 5. Disconnect the clutch hydraulic line from the slave cylinder. 6. Lower the vehicle. 7. Remove the clutch master cylinder reservoir and clutch master cylinder. Rotate the clutch master cylinder 45 degrees clockwise. 8. CAUTION: Clean all rubber clutch master cylinder parts with Ford High Performance DOT 3 Motor Vehicle Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A. Removal NOTE: When replacing clutch master cylinder (7A543), remove tubing from vehicle for bench bleeding procedure. 1. Disconnect the clutch master cylinder push rod from the clutch and brake pedal pivot shaft lever. 2. Disconnect the clutch pedal position switch (CPP) (11A152). 3. Remove the pushpins. 4. WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking, or towing an air suspension vehicle. This can be accomplished by turning off the rh kick panel area. Failure to inflation of deflation of the air springs which may result in shifting of the vehicle during these operations. Raise and support the vehicle. For additional information, refer to Section 100-02. 5. Disconnect the clutch hydraulic line from the slave cylinder. 6. Lower the vehicle. 7. Remove the clutch master cylinder reservoir and clutch master cylinder. Rotate the clutch master cylinder 45 degrees clockwise. 8. CAUTION: Clean all rubber clutch master cylinder parts with Ford High Performance DOT 3 Motor Vehicle Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.

Related entry:

99 chevy silverado clutch master cylinder line retainer pin, 2002 chevy Master Cylinder Diagram, 2002 chevy silverado 3500 master cylinder rebuild,

1999 Hyundai Tiburon HYUNDAI’ ’1.8L & 2.0L 4-Cylinder – 1996-04 (Except Sonata & 2004 Elantra) TIMING BELT REMOVAL & INSTALLATION

0

Filed Under (Hyundai) by admin on 06-04-2010

download
TIMING BELT Removal
1. Remove all drive belts and drive pulleys from crankshaft and water pump. Remove generator bolt, if necessary. Remove crankshaft pulley and water pump pulley. 2. Remove timing belt covers and gaskets, noting bolt lengths and locations. DO NOT rotate engine counterclockwise, as viewed from timing belt side of engine. Remove timing belt tensioner pulley. 3. Rotate engine clockwise to align all timing marks so No. 1 cylinder is at TDC of compression stroke. See Fig. 1 . If reusing belt, place mark on timing belt to indicate direction of belt rotation. Remove belt. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.

Related entry:

a/c tensioner 2002 hyandai elantra, how to replace the a/c tenision Pulley on 2001 hyundia elantra, 2002 hyundai elantra new tensioner, 1999 hyundai tiburon 16v DOHC ECT diagram location under hood, hyundai atos timing marks, how to replace 2003 tiburon ac compressor, how many belts in a 2002 hyundai elantra, how do yuo do replace on accent 2001 gear speedometer driven, haynes 1999 hyundai tiburon manual free download, 2002 hyundai elantra fixing ac where is ac,

Installation Manual TWM Performance Shifter Cable Bushing Kit 2001-2006 Hyundai Elantra 2003+ Hyundai Tiburon

0

Filed Under (Hyundai) by admin on 06-04-2010

download
1. Working in the engine bay, use a Phillips head screwdriver to remove the 2 screws over the driver’s side headlight and a 10mm
socket with a ratchet and an extension to remove the 10mm bolt holding the splash guard. Remove the splash guard from the engine bay. Loosen the 10mm bolt (shown by the top arrow) holding the top part of the air box to the throttle body inlet and unclip
the 2 clips holding this part of the air box to the bottom part (also shown by two arrows). Remove the top part of the air box and the
air filter as well. 2. Remove the three 10mm bolts at the bottom of the air box using the socket and ratchet with extension. Remove the bottom part of the air box from the engine bay.

Related entry:

schematics for automatic transmission for 1999 hyundai atos, 1999 hyundai tiburon manual, atos 2004 user manual, hyudai atoz ecu diagram wiring pdf download, Hyundai Bluetooth Manual, hyundai matrixworkshopmanual, hyundai veracruz bluetooth manual, naza ria kia sedona under carriage diagram,