2003 mercury sable fuse panel diagram
You are searching repair manual in PDF format about 2003 mercury sable fuse panel diagram use another keyword for search another post or files
Filed Under (Dodge) by admin on 17-08-2010
NOTE: Before starting this procedure, be certain to turn the steering wheel until the front wheels are in the straight-ahead position. 1. 2. 3. 4. 5. Disconnect and isolate the battery negative cable. Remove the trim from the right and left front door sills. Remove the trim from the left and right cowl side inner panels. Remove the steering column opening cover from the instrument panel. See: Steering Column Opening Cover and Knee Blocker Replacement Remove the two screws that secure the inside hood latch release handle to the instrument panel lower reinforcement and lower the release handle to the floor. Disconnect the driver side airbag module wire harness connector from the instrument panel wire harness at the instrument panel lower reinforcement. If the vehicle is so equipped, disconnect the overdrive lockout switch wire harness connector from the instrument panel wire harness near the instrument panel lower reinforcement. Remove the steering column from the vehicle, but do not remove the driver side airbag module, the steering wheel, or the switches from the steering column. Be certain that the steering wheel is locked and secured from rotation to prevent the loss of clockspring centering. Refer to Steering and Suspension/Steering/Steering Column/Service and Repair. See: Steering and Suspension/Steering/Steering Column/Service and Repair From under the driver side of the instrument panel, perform the following: a. Remove the screw from the center of the headlamp and dash to instrument panel bulkhead wire harness connector and disconnect the connector. b. Disconnect the two body wire harness connectors from the two instrument panel wire harness connectors that are secured to the outboard side of the instrument panel bulkhead connector. c. Disconnect the three wire harness connectors (one from the body wire harness, and two from the headlamp and dash wire harness) from the three junction block connector receptacles located closest to the dash panel. d. Unsnap the plastic retainer clip that secures the park brake release linkage rod to the lever on the back side of the park brake release handle and disengage the linkage rod end from the lever on the handle. e. Disconnect the instrument panel wire harness connector from the stop lamp switch connector receptacle. f. Disconnect the vacuum harness connector located near the left end of the heater-A/C housing. Remove the center support bracket from the instrument panel. See: Instrument Panel Center Support Bracket Replacement Remove the screw that secures the instrument panel wire harness ground eyelets to the left side of the Airbag Control Module (ACM) mount on the floor panel transmission tunnel. Disconnect the instrument panel wire harness connector from the ACM connector receptacle. Remove the glove box from the instrument panel. Refer to Body and Frame/Interior Trim/Glove Compartment/Service and Repair. See: Glove Compartment/Service and Repair Reaching through the instrument panel glove box opening, perform the following: a. Disconnect the two halves of the radio antenna coaxial cable connector near the center of the lower instrument panel glove box opening. b. Disengage the antenna half of the radio antenna coaxial cable from the retainer clip near the outboard side of the lower instrument panel glove box opening. c. Disconnect the blower motor wire harness connector located near the heater-A/C housing support brace on the inboard side of the instrument panel glove box opening. From under the passenger side of the instrument panel, perform the following: a. If the vehicle is so equipped, disconnect the two instrument panel wire harness connectors from the Infinity speaker amplifier connector receptacles on the right cowl side inner panel. b. Remove the nut that secures the instrument panel wire harness radio ground eyelet to the stud on the right cowl side inner panel. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
Filed Under (Dodge) by admin on 20-09-2010
Trim Panel: Service and Repair REMOVAL 1. Using a trim stick (C-4755), pry courtesy lamp from door trim. 2. Disconnect wire connector from courtesy lamp. 3. If equipped, remove screws attaching door assist handle to inner door panel. 4. If equipped, remove screw attaching door pull cup to inner door panel. 5. If equipped, remove screws attaching trim panel to door from below map pocket. 6. If equipped, remove window crank. 7. Using a trim stick, remove screw cover from switch panel. 8. Remove screws attaching switch panel to door trim. 9. Remove power accessary switch from door trim. 10. Disconnect power switch from wire connector. 11. If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector. 12. If equipped, remove screw holding door trim to door panel from behind inside latch release handle. 13. Disengage clips attaching door trim to door frame around perimeter of panel. 14. Lift trim panel upward to disengage flange from inner belt molding at top of door. 15. Tilt top of trim panel away from door to gain access to latch linkage. 16. Disengage clip attaching linkage rod to inside latch release handle. 17. Separate linkage rod from latch handle. 18. Remove front door trim panel from vehicle. INSTALLATION 1. Hold top of trim panel away from door to gain access to latch linkage. 2. Place linkage rod in position on latch handle. 3. Engage clip to hold linkage rod to inside latch release handle. 4. Place front door trim panel in position on door. 5. Install trim panel into inner belt molding at top of door. 6. Install clips to attach door trim to door frame around perimeter of panel. 7. If equipped, install screw to attach door trim to door panel behind inside latch release handle. 8. If equipped, connect power switch into wire connector. 9. Place power accessary switch in position on door trim. 10. Connect wire connector into memory seat/mirror switch and install switch into trim panel. 11. Install screws to attach accessary switch panel to door trim. 12. Install screw cover into switch panel. 13. If equipped, install window crank. 14. If equipped, install screws to attach trim panel to door inside map pocket. 15. If equipped, install screw to attach door pull cup to inner door panel. 16. If equipped, install screws to attach door assist handle to inner door panel. 17. Connect wire connector into courtesy lamp. 18. Install lamp in door trim.
Filed Under (Mercury) by admin on 10-06-2010
On all models, the fuse panel is located under the instrument panel, left of the steering column. Fig. 4: Interior Fuse Panel Identification (1994-95 Models) 1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid
Filed Under (Ford) by admin on 31-08-2009
repair and service manual covers Ford Taurus and Mercury Sable, 1996 through 2005. Note: this manual does not include information specific to SHO or variable fuel models.
Table of Contents
About this manual | Introduction to the Taurus, Sable | Vehicle identification numbers | Buying parts | Maintenance techniques, tools and working facilities | Jacking and towing | Booster battery (jump) starting | Automotive chemicals and lubricants | Conversion factors | Fraction/decimal/millimeter equivalents | Safety first! | Troubleshooting
Filed Under (Ford) by admin on 11-05-2010
Some 1999-2004 Navigator, 2002-2003 Blackwood, 2003-2005 Aviator, 2003-2004 Marauder and 2003-2004 Mustang vehicles built before 12/19/2004 equipped with 4.6L 4V/5.4 4V engine may exhibit a runs rough, lacks power, and engine misfire, prompted by a MIL light and DTC codes P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, and P0316. ACTION Diagnose engine for engine misfire concern. If diagnostics determine an engine misfire which is characterized by leakage through exhaust valve(s), only replace the affected cylinder head(s). SERVICE PROCEDURE