2004 AVEO CAMSHAFT SENSOR RELEARN


You are searching repair manual in PDF format about 2004 AVEO CAMSHAFT SENSOR RELEARN use another keyword for search another post or files



  2004 AVEO CAMSHAFT SENSOR RELEARN Direct Download speed 5787 Kb/s

  2004 AVEO CAMSHAFT SENSOR RELEARN Full Version speed 6767 Kb/s




1995 Ford Mustang Camshaft Position (CMP) Sensor Removal Installation

0

Filed Under (Ford) by admin on 08-02-2011

download
1. Disconnect battery ground cable (14301) . 2. Disconnect fuel charging wiring (9D930) from distributor stator (12A112) (camshaft position sensor). 3. Remove stator camshaft position sensor retaining screws and distributor stator (camshaft position sensor) from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the engine front cover (6019) , proceed with Removal Step 5. If camshaft position sensor housing is not being removed, proceed to Installation Step 6. 5. CAUTION: Before proceeding with this procedure, set cylinder No. 1 to 26 degrees After Top Dead Center (ATDC) of the compression stroke. Then note the position of the stator (camshaft position sensor) electrical connector. The installation procedure requires that the connector be located in the same position. Remove retaining bolt and hold-down clamp (12270) . 6. NOTE: The oil pump intermediate shaft (6A618) should be removed with the camshaft position sensor housing. Remove camshaft position sensor housing from engine front cover . Installation 1. CAUTION: If the replacement distributor stator (camshaft position sensor) does not contain a plastic locator cover tool, a special service tool such as Syncro Positioning Tool T89P-12200-A must be obtained prior to installation of the replacement distributor stator (camshaft position sensor). Failure to follow this procedure will result in improper stator (camshaft position sensor) alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. If the plastic locator cover tool is not attached to the replacement distributor stator (camshaft position sensor), attach Syncro Positioning Tool T89P-12200-A as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. The cover tool should be square and in contact with entire top surface of camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 30 degrees counterclockwise from the front face of the cylinder block (6010) . This step will locate stator (camshaft position sensor) electrical connector in the pre-removal position. 4. Install hold-down clamp and retaining bolt and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove Syncro Positioning Tool T89P-12200-A. 6. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install distributor stator (camshaft position sensor) and retaining screws. Tighten screws to 2.5-3.5 Nm (22-31 lb-in). 7. Connect fuel charging wiring connector to distributor stator (camshaft position sensor). 8. Connect battery ground cable .

Related entry:

2004 explorer tps install, 2006 ml350 left cam plug engine, replcing ect sensor on hyundai santa fe, reset throttle body 2005 Cobalt, how to replace a crankshaft sensor pigtail for a 2001 isuzu 2 2, HOW TO REPLACE CAM POSITION SENSOR 1993 300ZX?, twin cam peugeot 206 engine timing marks, inner fender removal to work on engine 2001 pt cruiser, cam gears for z18xer, lexus es 300 p0128,

1998 Ford Windstar Camshaft Position (CMP) Sensor REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 17-02-2011

download
CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126) , set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires the connector be located in the same position. Removal 1. Disconnect battery ground cable (14301). Refer to Section 14-01. 2. Disconnect fuel charging wiring connector from camshaft position sensor. 3. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to Step 6 of the installation procedures. 5. Remove hold-down clamp (12270) (bolt and washer assembly). 6. NOTE: Remove the oil pump intermediate shaft (6A618) with the camshaft position sensor housing. Remove camshaft position sensor housing from cylinder block. Installation 1. CAUTION: If the replacement camshaft position sensor housing does not contain a plastic locator cover tool, a special service tool must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the ignition fuel system being out of time with the engine, possibly causing engine damage. NOTE: For 3.0L engines, use Syncro Positioning Tool 303-589. For 3.8L engines, use Syncro Positioning Tool 303-562 (T96T-12200-A). If the plastic locator cover tool is not attached to the replacement camshaft position sensor housing, attach syncro positioning tool as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. Install camshaft position sensor housing so drive gear engagement occurs when arrow on syncro positioning tool is pointed approximately as shown in the illustrations. This step will locate camshaft position sensor electrical connector in the pre-removal position. 4. Install hold-down clamp (washer and bolt assembly) and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove syncro positioning tool. 6. CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor and retaining screws. On 3.0L engine, tighten screws to 2.5-3.5 Nm (23-30 lb-in). On 3.8L engine, tighten screws to 4.5-7 Nm (40-61 lb-in). 7. Connect fuel charging wiring connector to camshaft position sensor. 8. Connect battery ground cable. Refer to Section 14-01. Camshaft Position Sensor—3.0L Engine

Related entry:

1998 saturn sl2 transmission range switch adjustment,

1996 Ford Aerostar/Ranger/Explorer Camshaft Position (CMP) Sensor REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 30-03-2011

download
CAUTION: Syncro Positioning Tool T95T-12200-A (3.0L, 4.0L) or T96T-12200-A (5.0L) must be obtained prior to installation of the replacement synchronizer assembly. Failure to follow this procedure will result in the fuel system being out of time with the engine (6007), possibly causing engine damage. CAUTION: Prior to the removal of the camshaft position sensor (CMP sensor) (12A112), set No. 1 cylinder to 0 degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires that the electrical connector be located in the same position. Removal 1. Disconnect battery ground cable (14301). 2. Disconnect fuel charging wiring electrical connector from camshaft position sensor. 3. Remove the CMP sensor screws and camshaft position sensor from camshaft synchronizer. CAUTION: Do not move crankshaft (6303) until entire installation procedure is complete. Doing so will result in the fuel system being out of time with the engine resulting in possible emissions fault. NOTE: If camshaft synchronizer is to be removed from the cylinder block (6010), proceed with Step 4. If the camshaft synchronizer is not being removed, proceed to installation Step 8. 4. Remove hold-down clamp (12270). 5. Remove camshaft synchronizer from cylinder block. Installation 1. Attach Syncro Positioning Tool T95T-12200-A (3.0L, 4.0L) or T96T-12200-A (5.0L). Camshaft Synchronizer — 3.0L, 4.0L Camshaft Synchronizer — 5.0L 2. Align the synchronizer vane with the radial slot of the Syncro Positioning Tool T95T-12200-A (3.0L) or T96T-12200A (5.0L). 3. Rotate the tool on the synchronizer base until the tool’s boss engages the base notch. 4. Dip gear end into ESE-M2C123-A oil or equivalent to coat gear, thrust washer and lower bearing. Syncro Positioning Tool — 3.0L, 4.0L 5. CAUTION: Do not rotate crankshaft when syncro positioning tool is on the camshaft synchronizer. Armature tab will be damaged and synchronizer timing may be shifted. On 3.0L engines, install camshaft synchronizer so that drive gear engagement occurs when arrow on Syncro Positioning Tool T95T-12200-A is pointed approximately 75 degrees (3.0L), 60 degrees (4.0L) counterclockwise off the centerline of the engine. This step will locate camshaft position sensor electrical connector to the original position. Syncro Positioning Tool — 5.0L On 5.0L engines, install camshaft synchronizer into cylinder block making sure that arrow on Syncro Positioning Tool T96T-12200-A is pointing forward parallel to center line of crankshaft. This step will locate camshaft position sensor electrical connector to the pre-removal position. 6. CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the synchronizer assembly. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the synchronizer assembly and repeat Step 5. Install hold-down clamp and tighten to 19-30 Nm (14-22 lb-ft) on 3.0L, 4.0L and 23-34 Nm (17-25 lb-ft) on 5.0L. 7. Remove Syncro Positioning Tool. 8. Install CMP sensor and CMP sensor screws. Tighten to 2.5-3.5 Nm (23-30 lb-in). 9. Connect fuel charging wiring electrical connector to camshaft position sensor (CMP sensor). 10. NOTE: When battery voltage is removed from the powertrain control module (PCM) (12A650), all learned values will be cleared and reset to predetermined values. When battery voltage is restored to the PCM, the vehicle may exhibit certain driveability concerns. It will be necessary to drive the vehicle to allow the PCM to relearn values for optimum driveability and performance. Connect battery ground cable. Camshaft Position (CMP) Sensor — 3.0L Shown, 4.0L, 5.0L Similar

Related entry:

02 fordwindstar cam synchronizer 3 8 how to change, 4 2 ford cam syn adj, camshaft ford 4 2 you tube, how is the cam sensor timed on a ford windstar 3 8 engine, how to chang cam cencronizer e250 v6, lincoln aviator bank 1 sensor 2 location, video on how to change a camshaft synchronizer on a 2004 ford freestar with a 4 2, video on how to change a camshaft synkronizer on a 2004 ford freestar with a 4 2,

1999 Ford Taurus Camshaft Position (CMP) Sensor SHO Removal Installation

0

Filed Under (Ford) by admin on 11-02-2011

download
Camshaft Position (CMP) Sensor SHO Removal 1. Disconnect battery ground cable (14301) . Refer to Section 14-01. 2. Remove the engine appearance cover. For additional information, refer to Section 03-01C. 3. Disconnect engine control sensor wiring (12A581) from camshaft position sensor (CMP sensor) (6B288) . 4. Remove camshaft position sensor retaining bolt and remove camshaft position sensor from engine. Installation 1. Make sure camshaft position mounting sensor surface is clean and that camshaft position sensor O-ring is in proper location on camshaft position sensor . 2. CAUTION: Do not overtighten camshaft position sensor retaining bolt or damage to camshaft position sensor or engine mounting surface may occur. Position camshaft position sensor onto engine and install retaining bolt. Tighten retaining bolt to 8-12 Nm (71-106 lb-in). 3. Connect engine control sensor wiring to camshaft position sensor . 4. Install the engine appearance cover. For additional information, refer to Section 03-01C. 5. Connect battery ground cable . Camshaft Position Sensor

2003-2006 Chevrolet Express Antilock Brake (ABS) Activation At Low Speeds (Clean Wheel Speed Sensor Mounting Surface)

0

Filed Under (Chevrolet) by admin on 25-01-2011

download
Condition Some customers may comment on ABS activation at low speeds, usually below 8 km/h (5 mph). Upon investigation, the technician will find no DTCs set. Cause The cause of this condition may be an increased air gap between the wheel speed sensor and the hub reluctor ring due to rust and debris built up on the sensor mounting surface. Correction Measure AC voltage and clean the wheel speed sensor mounting surfaces. 1. 2. 3. 4. Raise and support the vehicle. Disconnect both the front wheel speed sensor connectors at the frame and harness. Place a Digital Volt Meter (DVM) across the terminals of each wheel speed sensor connector. Rotate the wheel clockwise approximately one revolution per second. The minimum reading should be at least 350 ACmV’s. If the reading is less than 350 ACmV’s, remove the wheel speed sensor. 5. Plug the wheel speed sensor bore in order to prevent debris from falling into the hub during service. 6. Clean the wheel speed sensor mounting surface using a wire brush, sand paper, emery cloth, scotch brite, or other suitable material. Be sure to thoroughly clean the wheel speed sensor surface. There should be no rust or corrosion. 7. Check the sensor head to determine if it has been warped/distorted due to the corrosion build up or other causes. Check the mounting surface on the sensor head for flatness by placing it on the edge of a metal machinists scale or other suitable straight edge to measure the flatness. Check the sensor for flatness in multiple (minimum 3) positions/directions. If the sensor head is distorted, replace the sensor. 8. Apply (spray) two thin coats of the specified rust penetrating lubricant (corrosion inhibitor) to the complete sensor mounting surface on the bearing hub. Allow to dry for 3-5 minutes between coats. Use ONLY Rust Penetrating Lubricant, P/N 89022217 (in Canada, P/N 89022218). 9. When the corrosion inhibitor is dry to the touch (about 10 minutes), apply a thin layer of bearing grease to the hub surface and sensor O-ring prior to sensor installation. Use ONLY Wheel Bearing Lubricant, P/N 01051344 (in Canada, P/N 993037). 10.Install either the original sensor or a new one in the hub. Ensure that the sensor is seated flush against the hub. Refer to the applicable Wheel Speed Sensor Replacement procedure in the ABS sub-section of the Service Manual. 11.Place the DVM across the sensor terminals and recheck the voltage while rotating the wheel. The voltage should now read at least 350 ACmV’s.

Related entry:

how replace 2011 kia sorento right wheel speed sensor, diagram of 2000 buick lesabre rear wheel speed sensor, how to replace abs sensor in 2002 sonoma, 2004 kia spectra speed sensor location, 2002 bmw 525i speed turbine sensor, where is the sensor for 2005 Buick LeSabre located on the transmission, how to replace rear wheel sensor on buick lacrosse, input speed sendor diagram for a 02 tracker, isuzi d max 2007 front right wheel speed sensor, kia sedona cuts out at speed,