2004 Silverado torque spec for front brake caliper


You are searching repair manual in PDF format about 2004 Silverado torque spec for front brake caliper use another keyword for search another post or files



  2004 Silverado torque spec for front brake caliper Direct Download speed 5787 Kb/s

  2004 Silverado torque spec for front brake caliper Full Version speed 6767 Kb/s




2004 Chrysler Pacifica DISC BRAKE SHOES Removal (Front)

0

Filed Under (Chrysler) by admin on 01-12-2010

download
1. Remove master cylinder fluid reservoir cap. 2. Raise and support vehicle. 3. Remove tire and wheel assembly. CAUTION: DO NOT overtighten C-clamp. 4. Place appropriately sized C-clamp over brake caliper, placing screw-drive head against outboard shoe and hook against rear of caliper. Slowly tighten screw-drive retracting caliper pistons into bores and brake outboard brake shoe free from caliper fingers. See Fig. 22 . Remove C-clamp. 5. Once outboard shoe is free from caliper fingers, slide caliper inboard on guides providing clearance between the rotor and inboard brake shoe. 6. Slide an appropriate prying tool through center opening in top of caliper behind brake shoe between 2 caliper pistons. Use care not to come in contact with pistons or dust boots potentially damaging them. Pry against rear of inboard brake shoe braking it free from caliper pistons. 7. Remove the 2 brake caliper guide pin bolts. See Fig. 23 . 8. Remove disc brake caliper from brake adapter and hang out of way using wire or a bungee cord. Use care not to overextend brake hose when doing this. 9. Remove brake shoes from disc brake caliper adapter. See Fig. 27 . 10. Install master cylinder fluid reservoir cap. Installation (Front) 1. Place brake shoes in anti-rattle clips on adapter. See Fig. 27 . Make sure clips are properly installed. See Fig. 26 . 2. Install disc brake caliper over brake shoes on brake caliper adapter. See CALIPER . 3. Align guide pin bolt holes with guide pins and install caliper guide pin bolts. See TORQUE SPECIFICATIONS . 4. Install tire and wheel assembly. See TORQUE SPECIFICATIONS . 5. Lower vehicle. 6. Pump brake pedal several times to seat shoes to caliper and brake rotor. 7. Check and fill brake fluid level as necessary. See CHECKING & FILLING under BRAKE FLUID in SERVICE. 8. Road test vehicle making several stops to wear off any foreign material on brakes and to seat brake shoes.

Related entry:

citroen dispatch brake disc removal, how to replace rear brake shoes on 1996 saturn sl, how do you push the rear caliper back in on a 2008-2014 acadia,

2004 Ford Expedition Brake Pads REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 28-02-2011

download
Removal 1. CAUTION: Install a new lining if worn to or past the specified thickness above the metal backing plate or rivets. Install new pads in complete axle sets. If necessary, using a suitable suction device, remove the brake fluid in the master cylinder reservoir until it is half filled. 2. Remove the wheel and tire assembly. For additional information, refer to Section 204-04. 3. Inspect the brake pads for wear or contamination. 4. CAUTION: If the anchor housing spring is to be reused, do not force the anchor housing spring off the brake caliper. Do not install a damaged anchor housing spring. Remove the anchor housing spring. 5. NOTE: Verify if the anchor housing spring has 1 end with 2 tabs. If yes, the LH side anchor housing spring must be installed with the 2-tabbed end in the upper brake caliper cavity. For the LH brake caliper, release the lower portion of the anchor housing spring. Apply force at the center of the anchor housing spring and pull outward at the bottom of the anchor housing spring to remove it from the lower brake caliper cavity. 6. Rotate the spring upward then remove it from the brake caliper. 7. NOTE: On the RH side, the anchor housing spring must be installed with the 2-tabbed end in the lower brake caliper cavity. The illustration below shows the anchor housing spring end with 2 tabs. For RH brake caliper, release the upper portion of the anchor housing spring. Apply force at the center of the anchor housing spring and pull outward at the top of the anchor housing spring to remove it from the upper brake caliper cavity. 8. Rotate the spring downward then remove it from the brake caliper. 9. NOTE: Do not allow the brake caliper to hang from the brake hose. Remove the brake caliper. 1. Remove the zero-drag spring. 2. Remove and discard the brake caliper-to-anchor plate bolts, guide pins and boots. 10. Remove the brake pads from the brake caliper. 11. NOTE: Use a wood block or used brake pad to protect the brake caliper piston boots. Compress the brake caliper pistons. 12. Measure the brake disc thickness. Install a new brake disc if it is not within specification. For additional information, refer to Brake Disc in this section.

Related entry:

2003 ford expedition brake caliper clip,

2008 Ford Expedition Brake Pads REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 04-03-2011

download
WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. WARNING: Always install new brake shoes or pads at both ends of an axle to reduce the possibility of brakes pulling vehicle to one side. Failure to follow this instruction may result in uneven braking and serious personal injury. NOTICE: Do not spill brake fluid onto painted or plastic surfaces or damage to surface may occur. If brake fluid is spilled onto a painted or plastic surface, immediately wash the surface with water. 1. Check the brake fluid level in the brake master cylinder reservoir. If required, remove the fluid until the brake master cylinder reservoir is half full. 2. Remove the wheel and tire. For additional information, refer to Section 204-04. 3. NOTICE: Do not allow the brake caliper to hang by the flexible brake hose or damage to the hose may occur. Remove the 2 brake caliper guide pin caps and bolts and position the caliper and brake pad assembly aside. Support the caliper using mechanic’s wire. Remove and discard the guide pin bushings. Inspect the guide pin threads for damage, install new guide pin(s) as necessary. 4. Remove the brake pads from the caliper. 5. Inspect the brake pads for wear or contamination and install new pads as necessary. For additional information, refer to General Procedures in Section 206-00. 6. Using a C-clamp and a worn brake pad, press the piston into the caliper. 7. Inspect the brake disc and resurface or install a new brake disc as necessary. For additional information, refer to General Procedures in Section 206-00. Installation 1. Clean, dry and inspect the brake caliper anchor plate. Apply equal amounts of the supplied yellow lubricant to the 4 brake pad contact points on the anchor plate as shown. 2. NOTICE: Do not apply lubricant to guide pin threads or incorrect tightening of the guide pins may result. Install new brake hardware as follows: Apply equal amounts of the supplied white lubricant to the inside of the guide pin bushings. Install the guide pin bushings into the caliper bores. Install the guide pins into the bushings. 3. Install the brake pads to the caliper. 4. Position the caliper onto the anchor plate and install the 2 brake caliper guide pin bolts. To install, tighten to 38 Nm (28 lb-ft). Clean and dry guide pin threads as necessary. 5. Fill the master cylinder with clean, specified brake fluid. 6. Install the wheel and tire. For additional information, refer to Section 204-04. 7. Apply the brake several times to verify correct brake operation.

Related entry:

1975 chev c65 brake system, 2008 buick emergency brake not engaging, 2008 dodge caliber drum brake repair, 2008 expedition brake pad instructions, 2009 chrysler town and country brakes are soft after repalcing rear caliper, changing brake disks on a 2008 dodge caliber, DIAGRAM FOR BRAKE LIGHT FUSE ON 2008 FORD CRWON VICTORIA, how to change rear brake pads 2009 town & country,

2007 Volkswagen Rabbit Brake pads removing and installing

0

Filed Under (volkswagen) by admin on 02-12-2010

download
Brake pads, removing When removing, mark brake pads that will be used again. Install in the same position, otherwise braking effect will be uneven! Remove wheels. Disconnect connector – 1 – for brake pad wear indicator. Remove caps – arrows -. Loosen both guide pins – arrows – and remove from brake caliper. Remove brake caliper and secure with wire so that the weight of the brake caliper does not burden or damage the brake hose. Remove brake pads from brake caliper. Cleaning: CAUTION: Do not blow brake system using compressed air, the dust produced is harmful to health! Thoroughly clean contact surfaces for brake pads at brake carrier, remove corrosion. Clean brake caliper. Use only appropriate solvents for cleaning brake caliper. Brake pads, installing Before pressing piston into cylinder using piston resetting tool, brake fluid must be extracted from brake fluid reservoir. Otherwise, especially if reservoir has been topped off, fluid will overflow and cause damage. Insert inner brake pad (piston side) – 1 – and outer brake pad – 2 – with retaining springs into brake caliper. Inner brake pad (piston side) with large three-finger clip – 1 -. Outer brake pad with small three-finger clip – 2 – (colored black). Place brake caliper with brake pads on brake carrier first at bottom – arrow -.

Related entry:

what is the minimum thickness for a brake rotor 2005 caravan, how to replace rear brake shoes on a 2001 mazda tribute, how to replace front brake pads on 2007 VW EOS, how to replace brake shoes on 2011 jetta, how to install rear brake pads in a 2007 hyundai tucson, how to change the back brakes on a 2010 mercury milan, how to change parting brake on 2004 gx470, how to change front brakes 2010 mazda 6, how to change brake pads rotors 2002 tracker, how to change brake pads on honda st1300,

2010 Toyota Prius Rear Brake Squeak

0

Filed Under (Toyota) by admin on 09-05-2011

download
Introduction Some 2010 Prius vehicles may experience rear brake squeak when backing up or moving forward during the ?rst few brake applications when the brakes are cold. An updated rear brake shim kit is available to reduce the likelihood of this condition occurring. Repair Procedure 1. Test drive the vehicle to con?rm the squeak is coming from the rear brakes. The condition occurs more frequently when backing up during light brake pedal application after cold soak. 2. Remove rear brake shims. Refer to the Technical Information System (TIS) 2010 Prius Repair Manual: Brake – Brake (Rear) Brake: Rear Brake: Removal 3. Clean the rear brake pad backing plates with a clean shop towel and apply a small amount of black disc brake grease to the backing plate of each rear brake pad. NOTE Make sure disc brake grease is not applied to the lining of the rear brake pads. 4. Install the No. 1 Anti-squeal shims. Install the No. 2 Anti-squeal shims. Figure 3. 5. Using the Variable Pin Wrench (SST 09960-10010), slowly rotate the caliper piston until the piston groove is positioned as shown in the illustration below. 6. Install new rear brake anti-squeal shims with brake pads into the rear caliper assemblies brackets. Refer to (TIS), 2010 Prius Repair Manual: Brake – Brake (Rear) Brake: Rear Brake: Installation NOTE • When installing the rear disc brake caliper assembly on the rear disc brake caliper mounting bracket, ensure the protrusion on the brake pad is centered in the caliper piston groove. • It is important to ensure the protrusion is not contacting the outer edges of the caliper piston groove. (both sides) 7. Road test the vehicle to con?rm the condition has been reduced.

Related entry:

2012 ml350 electronic brake service trear brake tool, replacing prius drum brakes, 2004 silverado rear brake assy parts view, 2002 suzuki xl-7 drum brake diagram, 2002 cavalier rear brake diagram, 2000 plymouth breeze drum back break digram, 1998 z24 cavlier rear brake line that mounts to rear axle part #, 1998 cavlier rear brake line that mount to rear axle, YouTube 2006 Chevy cobalt remove rear drum, 1994 ford ranger rear brake assembly diagram,