Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
1. With the vehicle in NEUTRAL, position on a hoist. For additional information, refer to Section 100-00. 2. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-00. 3. Remove the parts in the order indicated in the following illustration and table. 4. To install, reverse the removal procedure. 5. Fill the axle with the specified quantity of the specified lubricant. For additional information, refer to the Specifications in this section. Item 2: Rear Disc Brake Caliper Removal Note 1. CAUTION: Do not allow the caliper to hang from the brake hose. Provide a suitable support. Position the rear disc brake caliper aside. For additional information, refer to Section 206-00. Item 7: Differential Pinion Shaft Removal Note 1. Move the differential pinion shaft out far enough to remove the U-washers. Replace the shaft and install the lock bolt finger tight when U-washers are removed. Item 8: U-washer Removal Note 1. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers. 1. Push the axle shafts inboard. 2. Remove the U-washers. Item 10 and 11: Wheel Bearing Oil Seal and Axle Shaft Bearing Removal Note 1. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 8.8 inch rear axle, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. 2. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 9.75 inch and the 10.25 inch rear axles, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. Item 11: Axle Shaft Bearing Installation Note 1. For the 8.8 inch and the 9.75 inch rear axles, use the special tools to install the rear axle wheel bearing. 2. For the 10.25 inch rear axle, use the special tools shown to install the rear axle wheel bearing. Item 10: Wheel Bearing Oil Seal Installation Note 1. Use the special tools shown to install the rear wheel bearing oil seal. Item 8: U-washer Installation Note 1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers. 1. Position the two U-washers on the button end of the axle shafts. 2. Pull the axle shafts outward.

download
Caution: Refer to Brake Dust Caution in Service Precautions. Removal Procedure Tools Required J41013 Rotor Resurfacing Kit J42450-A Wheel Hub Resurfacing Kit 1. Release the park brake. 2. Raise and suitably support the vehicle. Refer to Vehicle Lifting.. 3. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 4. Mark the relationship of the rotor to the axle flange.5. Install a C-clamp over the body of the brake caliper, with the C-clamp ends against the rear of the caliper body and the outboard disc brake pad. 6. Slowly tighten the C-clamp until the pistons are pushed into the caliper bores enough to remove the caliper from the pads. 7. Remove the C-clamp from the caliper. 8. Remove the brake caliper bracket mounting bolts.

download
WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in personal injury. CAUTION: Do not spill brake fluid onto painted or plastic surfaces. If spilled, wipe up immediately before damage to the plastic or painted surfaces occurs. 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-00. 2. Remove the parts in the order indicated in the following illustration and table. To remove individual parts, only carry out the listed steps: 3. To install, reverse the removal procedure. 4. If the hydraulic system was opened, bleed the brake system. For additional information, refer to Brake System Bleeding in this section. Item 2: Brake Caliper Removal Note 1. CAUTION: Do not allow the brake caliper to hang by the flexible brake hose. Support the caliper to the vehicle. Item 11: Brake Disc Removal Note 1. If removing the brake disc, only remove the caliper bracket bolts and position the caliper and bracket aside. Item 10: Spindle Nut Installation Note 1. Tighten the spindle nut to the specified torque. Rotate the hub counter-clockwise 5 rotations and then recheck the torque. Item 3: Brake Disc Pads Installation Note 1. CAUTION: Install a new lining if worn to or past the specified thickness above the metal backing plate or if the pad is damaged. Install new pads in complete axle sets. If replacing the brake pads, use a suitable suction device, remove the brake fluid in the master cylinder reservoir until it is half filled. 2. If replacing the brake pads, use a suitable tool to push the brake caliper pistons into the caliper bore. 3. One brake disc pad kit contains the pads required for both the RH and LH side. Item 1: Caliper Bolt Installation Note 1. Tighten the bottom caliper bolt and then the top caliper bolt. Item 11: Brake Disc Inspection Note 1. NOTE: If machining is necessary use a hub-mount brake lathe to machine the front brake disc. For additional information, refer to section Section 100-04. Measure the front brake disc, and resurface as necessary. Install a new front brake disc if beyond specification.

download
Removal NOTE: If, for any reason, the rear hub (1109) is removed from the spindle, the old hub seal must be removed and a new hub seal installed. 1. Set the parking brake and loosen the eight axle shaft retaining bolts. 2. Raise the vehicle to the desired working height, keeping the axle parallel with the floor. 3. Release parking brake and back off the rear brake adjustment, if necessary. 4. Remove the wheel (1007). 5. Remove brake drum (1126). Push-on (sheet metal) drum retainer nuts may be discarded. Push-on retainer nuts are used for shipping purposes only and have no vehicle function. If retainers are not flush against the drum, the retainers can prevent the wheel from being flat against the drum, which could contribute to vibration. 6. Place a drain pan under the axle shaft (4234) and rear hub. Remove the eight 7/16-inch axle shaft bolts and remove the axle shaft. Axle Shaft Removal 7. CAUTION: The right hub nuts are right-hand thread; the left hub nuts are left-hand thread. Each hub nut is stamped RH for the right hub nut or LH for the left hub nut. Install Locknut Wrench T85T-4252-AH so that the drive tangs of the tool engage the four slots in the hub nut. 8. CAUTION: A new hub nut must be installed if used hub nut comes apart during removal or installation. CAUTION: Under no circumstances are power impact tools to be used when performing these operations. NOTE: The hub nut will ratchet during this operation. Remove hub nut (counterclockwise for right-hand thread; clockwise for left-hand thread). 9. Install Step Plate Adapter D80L-630-7 (Part of Step Plate Adapter Set D80L-630-A) or equivalent. 10. Install 2-Jaw Puller D80L-1002-L or equivalent and loosen rear hub to the point of removal. 11. CAUTION: Do not drop outer hub bearing when removing. Remove rear hub assembly.

download
CAUTION: Refer to Brake Dust Caution in Cautions and Notices. 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, then no brake fluid needs to be removed from the reservoir before proceeding. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, then remove brake fluid to the midway point before proceeding. 3. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 4. Remove the rear tire and the wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 5. Install a hand tightened lug nut to retain the rotor to the hub. 6. Compress the caliper piston enough for clearance. Use a C-clamp (3). NOTE: NOTE: Use care to avoid damaging pin boot when rotating caliper. Support the brake caliper with heavy mechanic’s wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.