2004 chevy colorado change abs speed sensor


You are searching repair manual in PDF format about 2004 chevy colorado change abs speed sensor use another keyword for search another post or files



  2004 chevy colorado change abs speed sensor Direct Download speed 5787 Kb/s

  2004 chevy colorado change abs speed sensor Full Version speed 6767 Kb/s




2003-2006 Chevrolet Express Antilock Brake (ABS) Activation At Low Speeds (Clean Wheel Speed Sensor Mounting Surface)

0

Filed Under (Chevrolet) by admin on 25-01-2011

download
Condition Some customers may comment on ABS activation at low speeds, usually below 8 km/h (5 mph). Upon investigation, the technician will find no DTCs set. Cause The cause of this condition may be an increased air gap between the wheel speed sensor and the hub reluctor ring due to rust and debris built up on the sensor mounting surface. Correction Measure AC voltage and clean the wheel speed sensor mounting surfaces. 1. 2. 3. 4. Raise and support the vehicle. Disconnect both the front wheel speed sensor connectors at the frame and harness. Place a Digital Volt Meter (DVM) across the terminals of each wheel speed sensor connector. Rotate the wheel clockwise approximately one revolution per second. The minimum reading should be at least 350 ACmV’s. If the reading is less than 350 ACmV’s, remove the wheel speed sensor. 5. Plug the wheel speed sensor bore in order to prevent debris from falling into the hub during service. 6. Clean the wheel speed sensor mounting surface using a wire brush, sand paper, emery cloth, scotch brite, or other suitable material. Be sure to thoroughly clean the wheel speed sensor surface. There should be no rust or corrosion. 7. Check the sensor head to determine if it has been warped/distorted due to the corrosion build up or other causes. Check the mounting surface on the sensor head for flatness by placing it on the edge of a metal machinists scale or other suitable straight edge to measure the flatness. Check the sensor for flatness in multiple (minimum 3) positions/directions. If the sensor head is distorted, replace the sensor. 8. Apply (spray) two thin coats of the specified rust penetrating lubricant (corrosion inhibitor) to the complete sensor mounting surface on the bearing hub. Allow to dry for 3-5 minutes between coats. Use ONLY Rust Penetrating Lubricant, P/N 89022217 (in Canada, P/N 89022218). 9. When the corrosion inhibitor is dry to the touch (about 10 minutes), apply a thin layer of bearing grease to the hub surface and sensor O-ring prior to sensor installation. Use ONLY Wheel Bearing Lubricant, P/N 01051344 (in Canada, P/N 993037). 10.Install either the original sensor or a new one in the hub. Ensure that the sensor is seated flush against the hub. Refer to the applicable Wheel Speed Sensor Replacement procedure in the ABS sub-section of the Service Manual. 11.Place the DVM across the sensor terminals and recheck the voltage while rotating the wheel. The voltage should now read at least 350 ACmV’s.

Related entry:

2005 highlander rear wheel bearing and speed sensor harness, where is 2005 Buick Lesabre Speed Sensor located, 2007colorado frunt abs sensers, 07 ford edge turbine sensor, location of turbine sensors on 07 ford edge, speed sensor location 2002 gmc sonoma 4 wheel drive, locate abs sensor on 2003 ford f150, changing a speed sensor on a 2004 kia spectra, www 2003 camry intermediate shaft speed sensor A location, where is transmission speed sensor on 1999 ford f250,

2006 Honda Civic Rear ABS Wheel Speed Sensor and O-Ring Inspection

0

Filed Under (Honda) by admin on 10-01-2011

download
During assembly, some wheel speed sensors may have been improperly installed and do not seal the hub assembly. Water may enter the hub assembly and damage the wheel bearing. In areas where road salt is used, the wheel bearings may corrode, which may cause the wheel to separate and fall off, increasing the risk of a crash. CORRECTIVE ACTION Inspect both rear ABS wheel speed sensors and their O-rings. If an ABS wheel speed sensor or O-ring is damaged, replace the damaged part and the hub bearing unit on that wheel. REPAIR PROCEDURE 1. 2. 3. 4. Raise the vehicle on a lift. Remove the rear wheels. Remove both rear ABS wheel speed sensors. Inspect the rear ABS wheel speed sensors and their O-rings. • If a rear ABS wheel speed sensor O-ring is damaged (cut, torn, pinched, or flattened), replace the O-ring and the corresponding rear hub bearing unit, then go to step 5. DAMAGED O-RINGS: O-ring is pinched. • If the rear ABS wheel speed sensor tip has any physical damage, remove the original sensor assembly, replace the corresponding rear hub bearing unit(s), and connect the new sensor’s wire harness. Then go to step 5. – Refer to page 18-34 (with disc brakes) or 18-36 (with drum brakes) of the 2006–07 Civic Service Manual, or – Online, enter keyword HUB, then select Rear Knuckle/Hub Bearing Unit Replacement from the list. O-ring is rolled out of the groove and flattened. -Refer to page 18-34 (with disc brakes) or 18-36 (with drum brakes) of the 2006–07 Civic Service Manual, or – Online, enter keyword HUB, then select Rear Knuckle/Hub Bearing Unit Replacement from the list. • If the rear ABS wheel speed sensors and their O-rings are OK, go to step 5. 5. Lubricate the ABS wheel speed sensor O-ring and the sensor hole in the knuckle with multi-purpose grease.

Related entry:

Rear Hub Assembly Diagram, 2008 lincoln mkx abs sensor ring, avalanche rear speed sensor, bj5p crank sensor, 2006 escape wheel sensor ring replace, Diagram of the speed sensor on a 2007 chevy equinox, HOW TO REPLACE WIREHARNESS BUICK RENDEZVOUS ABS SPEED SENSOR, how to replace a rear hub on a chevy equinox, how to change front wheelhub assassembly on 07 hyundai santa fe all wheel drive, lincoln mkx abs ring,

2007 Chevrolet Colorado WHEEL HUB/ SPEED SENSOR REPLACEMENT

0

Filed Under (Chevrolet) by admin on 25-05-2010

download
Removal Procedure CAUTION: Refer to Brake Dust Caution . CAUTION: Refer to ABS Component Handling Caution . IMPORTANT: The wheel hub and speed sensor are serviced as an assembly. The are not service as individual items. 1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle . 2. Remove the front brake caliper. Refer to Brake Caliper Replacement . Fig. 20: View Of ABS Speed Sensor Wiring Harness Remove the front retaining bolt for the speed sensor bracket at the upper control arm. Fig. 21: View Of Speed Sensor Bracket Front Retaining Bolt

1995 Ford Mustang Camshaft Position (CMP) Sensor Removal Installation

0

Filed Under (Ford) by admin on 08-02-2011

download
1. Disconnect battery ground cable (14301) . 2. Disconnect fuel charging wiring (9D930) from distributor stator (12A112) (camshaft position sensor). 3. Remove stator camshaft position sensor retaining screws and distributor stator (camshaft position sensor) from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the engine front cover (6019) , proceed with Removal Step 5. If camshaft position sensor housing is not being removed, proceed to Installation Step 6. 5. CAUTION: Before proceeding with this procedure, set cylinder No. 1 to 26 degrees After Top Dead Center (ATDC) of the compression stroke. Then note the position of the stator (camshaft position sensor) electrical connector. The installation procedure requires that the connector be located in the same position. Remove retaining bolt and hold-down clamp (12270) . 6. NOTE: The oil pump intermediate shaft (6A618) should be removed with the camshaft position sensor housing. Remove camshaft position sensor housing from engine front cover . Installation 1. CAUTION: If the replacement distributor stator (camshaft position sensor) does not contain a plastic locator cover tool, a special service tool such as Syncro Positioning Tool T89P-12200-A must be obtained prior to installation of the replacement distributor stator (camshaft position sensor). Failure to follow this procedure will result in improper stator (camshaft position sensor) alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. If the plastic locator cover tool is not attached to the replacement distributor stator (camshaft position sensor), attach Syncro Positioning Tool T89P-12200-A as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. The cover tool should be square and in contact with entire top surface of camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 30 degrees counterclockwise from the front face of the cylinder block (6010) . This step will locate stator (camshaft position sensor) electrical connector in the pre-removal position. 4. Install hold-down clamp and retaining bolt and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove Syncro Positioning Tool T89P-12200-A. 6. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install distributor stator (camshaft position sensor) and retaining screws. Tighten screws to 2.5-3.5 Nm (22-31 lb-in). 7. Connect fuel charging wiring connector to distributor stator (camshaft position sensor). 8. Connect battery ground cable .

Related entry:

shematic diagram oxygen sensor chrysler pacifica, 2005 freestyle brake sensor disconection, how to repair a camshaft sensor on a 2000 Suzuki vitara, ml320 ambient sensor diagram, cam sensor 1991 cadillac seville, cam positioning tool for 2002 landrover freelander 2 5 liter, 2002 cavalier replace throttle positiong sensor, were is the crank shaft located on the engine of a golf, cam bolt torque specs 2002 nissan 2 5, removing 300zx cam position sensor,

1998 Ford Windstar Camshaft Position (CMP) Sensor REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 17-02-2011

download
CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126) , set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires the connector be located in the same position. Removal 1. Disconnect battery ground cable (14301). Refer to Section 14-01. 2. Disconnect fuel charging wiring connector from camshaft position sensor. 3. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to Step 6 of the installation procedures. 5. Remove hold-down clamp (12270) (bolt and washer assembly). 6. NOTE: Remove the oil pump intermediate shaft (6A618) with the camshaft position sensor housing. Remove camshaft position sensor housing from cylinder block. Installation 1. CAUTION: If the replacement camshaft position sensor housing does not contain a plastic locator cover tool, a special service tool must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the ignition fuel system being out of time with the engine, possibly causing engine damage. NOTE: For 3.0L engines, use Syncro Positioning Tool 303-589. For 3.8L engines, use Syncro Positioning Tool 303-562 (T96T-12200-A). If the plastic locator cover tool is not attached to the replacement camshaft position sensor housing, attach syncro positioning tool as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. Install camshaft position sensor housing so drive gear engagement occurs when arrow on syncro positioning tool is pointed approximately as shown in the illustrations. This step will locate camshaft position sensor electrical connector in the pre-removal position. 4. Install hold-down clamp (washer and bolt assembly) and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove syncro positioning tool. 6. CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor and retaining screws. On 3.0L engine, tighten screws to 2.5-3.5 Nm (23-30 lb-in). On 3.8L engine, tighten screws to 4.5-7 Nm (40-61 lb-in). 7. Connect fuel charging wiring connector to camshaft position sensor. 8. Connect battery ground cable. Refer to Section 14-01. Camshaft Position Sensor—3.0L Engine

Related entry:

como checar crankshaft posicion sensor rodeo isuzu 1998, what sensors on back of block 5 3, how to remove the wiring harness 2008 pt cruiser ect sensor, 2003 kia optima crank sensor removal, 2004 F250 ICP Sensor location, diagram of where low coolant sensor is on Northstar 4 0, how to adjust throttle position sensor 2002 escort, location tps 2000 windstar, locations of crankshaft position sensors 2008 camry four cylinder, ohm reading on a tps 97 ford escort,