2004 chevy suburban trouble code p0174


You are searching repair manual in PDF format about 2004 chevy suburban trouble code p0174 use another keyword for search another post or files



  2004 chevy suburban trouble code p0174 Direct Download speed 5787 Kb/s

  2004 chevy suburban trouble code p0174 Full Version speed 6767 Kb/s




1995 Ford Thunderbird Antilock Brakes / Traction Control Systems: Testing and Inspection Displaying and Reading Trouble Codes

0

Filed Under (Ford) by admin on 14-08-2010

download
NOTE: Ford DOES NOT provide procedures to retrieve or clear trouble codes without the Super Star II tester. The anti-lock brake/traction assist system has on-board diagnostic capabilities. However, the module as received from manufacturing is equipped with a stored error code (61). This will affect the service procedure. The error codes can be retrieved from the ABS module in the following manner. 1. 2. 3. 4. Connect Super STAR II tester to connector located in engine compartment on the power distribution box. Turn on Super STAR II tester and latch button down in TEST position. Turn ignition switch to RUN position. Read first code output. After approximately 15 seconds, the next code will be output. Leave button latched until all codes are output. NOTE: Make sure that all codes are written down. 5. The diagnostic procedure should be as follows provided that the CHECK ANTI-LOCK BRAKE indicator stays on all the time or flashes intermittently. NOTE: If the BRAKE warning indicator is on or intermittently comes on, refer to the Warning Indicator Symptom Chart. NOTE: If there are more codes stored in the anti-lock brake control module memory, no codes will erase until all codes have been output by the Super STAR II tester, all malfunctions have been serviced and the vehicle is driven about 40 km/h (25 mph). This means that if a 20s code originally existed and was serviced, it can be ignored when running the on-board diagnostic the second time. If the first code received is 18, 19 or in the 20s and no other code is received, service the indicated component. No other codes can be output if a 20s code exists. After servicing the indicated 18, 19, or 20s code, repeat the procedure for retrieving error codes. 6. If a code 61 is received with any other code, ignore the code 61 and service the other indicated components. If, after correcting all other indicated malfunctions, the CHECK ANTI-LOCK BRAKE indicator is still on, service the Fluid Level Switch (FLS) circuit. 7. If a code 61 is received and no other codes are received, service the FLS circuit. 8. If no code, or only a code 10 is received, use the Anti-Lock Quick Check Sheet since some possibilities are not recognized and retained in the anti-lock brake control module memory. See: Trouble Code Descriptions/Quick Check Sheet 9. When dealing with intermittent ABS warning light ON concern, make certain to visually inspect all wiring related to the component associated with the code received.

Related entry:

International Trouble Code Chart, 02 liconl town car code b 1681, 2010 Sprinter Trouble Codes, international code 3981 2 33 1, pcode 2440 trailblazer 2006, 2000 mercedes e55 srs code b1865, 1994 ford ranger codes, international esc codes, spn 524285 fmi 14, 1995 cadillac error messages,

2001 Nissan Pathfinder The check engine light is on with a trouble code P1140

0

Filed Under (Nissan) by admin on 21-12-2010

download
Customer Concern: Tests/Procedures: Potential Causes: Tech Tips: Diagnostic Codes: The check engine light is on with a trouble code P1140. 1. Check the right side (passenger side) Intake Valve Timing Control Position (IVTCP) sensor for 12 volts on the Black/White wire. 2. Check the IVTCP sensor for a good ground on the Black wire. 3. Scope the Yellow/Green signal wire and look for a square wave signal of around 8 volts. Check the pattern of the right side sensor and if unsure of the pattern, compare it to the left bank sensor. IVTCP Sensor Wiring — IVTCP sensor wiring/connection. This code is for the right (passenger) bank IVTCP Sensor or sensor circuit. The right and left bank sensors can be swapped from side to side to see if the code will follow the sensor. The sensor is on top of the timing cover. P1140

1998 Mercedes Benz SLK 230 DTCM – Diagnostic Trouble Code Memory

0

Filed Under (Mercedes-Benz) by admin on 14-08-2010

download
Do not connect battery trickle charger. Risk of Injurywhen performing diagnostic tests and repairs on components of the SRS system. Store both airbags and side airbags with opening surface pointing upward. Do not expose to temperatures above 100°C . Preliminary work: Diagnosis – Function Test. See: FT – Function Test Preparation for DTC Readout : 1. 2. 3. 4. 5. Review DTC Memory and Actual Values. Fuses OK. Battery voltage 11 – 14 V SRS MIL (A1e15) illuminates. Connect Hand-Held Tester (HHT) as per connection diagram and readout DTC memory. WARNING: Interrupt any electrical current from reaching the airbag unit. NOTE: As of 07/93, diagnostic trouble codes (DTC’s) can only be read out and erased using the Hand-Held Tester (HHT). Determine MB number of the SRS control module via HHT (See DTC Chart). The SRS control modules beginning with the number 000, the fault code 1 is valid. Those beginning with 001, the fault code 2 is valid. NOTE : When installing additional accessories, observe harness clearances near SRS sensor lines. Test equipment : Hand-Held Tester (HHT) (Available through the MBNA Standard Equipment Program.)

Related entry:

1996 mercedes srs fault, 2002 mercedes srs codes, 2002 slk 230 knock senser, mercedes srs code b1865 ignition circuit 6, mercedes srs codes, srs fault light,

VW MKIII Golf / Jetta Technical Bulletin Diagnostic Trouble Code (DTC)

0

Filed Under (volkswagen) by admin on 30-03-2010

download
Diagnostic Trouble Code (DTC) Memory, displaying blink codes Starting with 8.94 production (1995 m.y.), Golf///,
Jetta/// and Cabrio vehicles are equipped with a special OBD1 adapter for use with the On Board Diagnostic (OBD) system. The adapter is used to check Diagnostic Trouble Code (DTC) Memory when the VAG 1551 Scan Tool
(ST) is not available. Stored malfunctions are displayed as blink codes by the Malfunction Indicator Lamp (MIL) in the vehicle.
play is activated by using the adapter in conjunction with the vehicle’s Data Link Connector (DLC). The adapter makes connection between connector sockets 15 (L-wire) and 4 (Battery Ground)

Related entry:

03 honda accord 2 4lt hvac dtc retreival, 2023-14A, stored diagnostics code, p2110 ford explorer, p0300 p0306 saturn vue, obm 2 code 0496 and 0496p, navistar l fault code 639-14p, international 2023-14a, international 2006 diagnostic charts, ih code 2023-14a,

2003-2004 FORD Mustang ENGINE MISFIRE WITH DIAGNOSTIC TROUBLE CODE (DTC) P0301

0

Filed Under (Ford) by admin on 13-01-2011

download
Some 1999-2004 Navigator, 2002-2003 Blackwood, 2003-2005 Aviator, 2003-2004 Marauder and 2003-2004 Mustang vehicles built before 12/19/2004 equipped with 4.6L 4V/5.4 4V engine may exhibit a runs rough, lacks power, and engine misfire, prompted by a MIL light and DTC codes P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, and P0316. ACTION Diagnose engine for engine misfire concern. If diagnostics determine an engine misfire which is characterized by leakage through exhaust valve(s), only replace the affected cylinder head(s). SERVICE PROCEDURE FOR VEHICLES WITH RUNS ROUGH/MISFIRE CONDITION: 1. Perform relative compression check on all cylinders. If abnormal, check cylinder leakage and actual compression for “low” cylinders refer to Workshop Manual (WSM), Section 303-00. 2. If leakage/compression check indicates a valve train concern, per valve train diagnostics in WSM, Section 303-00, replace cylinder head and cam assembly, pipe plugs and timing chain tensioner, per procedure outlined in WSM, Section 303-01. 3. If cylinder leakage and compression tests are inconclusive, perform misfire diagnostic, per TSB 05-22-8.

Related entry:

codigo de error kia sorento 2005 p0304,