2004 envoy xuv midgate


You are searching repair manual in PDF format about 2004 envoy xuv midgate use another keyword for search another post or files



  2004 envoy xuv midgate Direct Download speed 5787 Kb/s

  2004 envoy xuv midgate Full Version speed 6767 Kb/s




Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool

0

Filed Under (Uncategorized) by on 15-09-2009

Check the following wire connection for open circuit according to wiring diagram:Relay carrier in E-box, plenum chamber, position 3Terminal Harness connector atignition coils Terminal 8 1 Specified value: Wire resistance max 1.5 – If necessary, repair wire connection. Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool, Engi…Page 5 24-158 If no malfunctions are found in wires: – Check voltage supply of Motronic Engine Control Module (ECM) voltage supply relay – J271 – Page 24-158 . – Check activation of Motronic Engine Control
Module (ECM) voltage supply relay – J271 – Page 24-159 . Checking voltage supply If specified value is not obtained:
- Connect multimeter for voltage measurement as follows. Relay carrier in E-box, plenum chamber, position 3
Terminal

ENGINE MISFIRE 2003-2004 Mustang, 1999-2004 Navigator 2002-2003 Blackwood 2003-2005 Aviator 2003-2004 Marauder

0

Filed Under (Uncategorized) by on 11-05-2010

download
Some 1999-2004 Navigator, 2002-2003 Blackwood, 2003-2005 Aviator, 2003-2004 Marauder and 2003-2004 Mustang vehicles built before 12/19/2004 equipped with 4.6L 4V/5.4 4V engine may exhibit a runs rough, lacks power, and engine misfire, prompted by a MIL light and DTC codes P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, and P0316. ACTION Diagnose engine for engine misfire concern. If diagnostics determine an engine misfire which is characterized by leakage through exhaust valve(s), only replace the affected cylinder head(s). SERVICE PROCEDURE

2004 Hyundai Sonata 2003-2004 Hyundai Santa FE 2004 Kia Optima no spark Problem and Repair

0

Filed Under (Uncategorized) by on 25-04-2010

download
1. At the crank position sensor, check for battery voltage to be present on the Red wire with the key on and cranking. The Black wire should be a good ground and the Blue wire should have 5 volts on it from the computer. One may have to disconnect the crank sensor to check for the 5 volt reference. 2. During crank look for a good 5 volt square wave signal on the Blue wire. 3. Check at the ignition coils for good battery voltage key on and cranking. If there is a loss of voltage during crank check the ignition failsafe relay. 4. Check for any stored engine codes. Crankshaft Position (CKP) Sensor Ignition Failsafe Sensor The ignition failsafe sensor supplies battery voltage to the ignition coils. The ignition coils can look like they have good battery voltage key on but during crank the ignition failsafe relay can stop sending voltage to the ignition coils.

2004-2005 Ford Thunderbird DELAYED OR HARSH REVERSE ENGAGEMENTS— 5R55S TRANSMISSION

0

Filed Under (Uncategorized) by on 16-12-2010

download
FORD: 2004-2005 Thunderbird, Explorer LINCOLN: 2004-2005 LS, Aviator MERCURY: 2004-2005 Mountaineer This article supersedes TSB 05-15-4 to correct the Service Procedure. ISSUE Some 2004-2005 vehicles built prior to 09/23/2004 and equipped with the 5R55S transmission, may exhibit a delayed or harsh reverse engagement. This condition may be due to improper pressure control. ACTION It may be necessary to replace the solenoid body assembly. Refer to the following Service Procedure. SERVICE PROCEDURE NOTE INSTALLING TRANSMISSION ADDITIVE WILL PREVENT THE SYMPTOM ON SOLENOIDS THAT DO NOT YET EXHIBIT THE CONDITION BUT WILL NOT RESOLVE THE CONDITION IF IT ALREADY EXISTS. LINCOLN LS AND THUNDERBIRD ONLY 1. Lower the transmission cross member and transmission to gain access to the pressure control solenoid-C (PCC) port. DO NOT disconnect the drive shaft. 2. Install pressure gauge per Step 2 of “DIAGNOSTICS”, below. 3. Reinstall cross member and snug the fasteners for diagnostic purposes only. 4. Proceed with the “DIAGNOSTICS” section of this TSB. 5. After the TSB repair is completed, torque the cross member fasteners to 41 lb-ft (55 N•m). DIAGNOSTICS – ALL VEHICLES 1. Remove pressure tap plug at PCC port (Figure 1).

COLD AIR SYSTEM Installation Instructions 2003-2004 Toyota Corolla 2002-2004 Toyota Matrix XR

0

Filed Under (Uncategorized) by on 16-04-2010

download
Removing the stock air inlet system
a) Before removing any of the O.E. components, label each individual part so that no components become mixed up during the installation process. There are two Vacuum Switching Valves (VSV), and one air flow meter that have electrical and/or vacuum connections going to them. Be sure to label these connections before disconnecting them.
Remove b) Remove the two nuts and two plastic rivets that hold the plastic engine cover on. The
plastic rivets may be gently lifted with a small screwdriver. Remove the cover. c) Remove the bolt in the radiator support that holds the battery bracket. Unhook the rod at the rear of the battery bracket. Remove the battery from the vehicle