2004 gmc envoy torque converter solenoid


You are searching repair manual in PDF format about 2004 gmc envoy torque converter solenoid use another keyword for search another post or files



  2004 gmc envoy torque converter solenoid Direct Download speed 5787 Kb/s

  2004 gmc envoy torque converter solenoid Full Version speed 6767 Kb/s




2007 Dodge Nitro R/T CONVERTER-TORQUE DESCRIPTION

0

Filed Under (Dodge) by admin on 17-03-2011

download
CAUTION: The torque converter must be replaced if a transmission failure resulted in large amounts of metal or fiber contamination in the fluid. The torque converter is a hydraulic device that couples the engine crankshaft to the transmission. The torque converter consists of an outer shell with an internal turbine (1), a stator (3), an overrunning clutch, an impeller (2), and an electronically applied converter clutch. The converter clutch provides reduced engine speed and greater fuel economy when engaged. Clutch engagement also provides reduced transmission fluid temperatures. The converter clutch engages in third through fifth gears. The torque converter hub drives the transmission oil (fluid) pump. See Fig. 267. A turbine damper (6) has been added for some applications to help improve vehicle noise, vibration, and harshness (NVH) characteristics. The torque converter is a sealed, welded unit that is not repairable and is serviced as an assembly. IMPELLER

Related entry:

01 silverado torque converter removal, 2000 neon Torque Converter Circuit Solenoid, 2008 COROLLA TORQUE CONVERTER CLUTCH SOLENOID PART, causes of a torque converter lock up malfunction on a 2001 chrysler concorde, find how to remove torque converter bolts from a 2001 ford explorer sport, HOW TO FILL TORQUE CONVERTER 2004 CROWN VIC, replace torque converter 4 6 crown vic, what else can cause a torque converter lock up malfunction on a 2001 chrysler concorde,

1994 Ford Mustang Dual Converter and Pipe 5.0L Engine Removal Installation

0

Filed Under (Ford) by admin on 07-02-2011

download
5.0L Engine Removal 1. Raise vehicle. Refer to Section 00-02. 2. Disconnect air inlet tube (5F235) from the dual converter and pipe. 3. Remove dual converter and pipe to exhaust manifold retaining nuts. 4. Remove muffler inlet flange to dual converter and pipe outlet flange retaining nuts. 5. Support dual converter and pipe with a suitable jackstand and remove exhaust converter frame bracket to dual converter and pipe retaining nuts. 6. Remove dual converter and pipe from vehicle. 7. Replace any damaged parts. Installation 1. Loosely install dual converter and pipe and support with a suitable jackstand. 2. Install dual converter and pipe onto exhaust converter frame bracket (5E269) and install retaining nuts. Tighten retaining nuts to 14.8-20.2 Nm (11-15 lb-ft). 3. Position dual converter and pipe to exhaust manifold studs and install retaining nuts. Do not tighten nuts. 4. Position muffler inlet flanges to dual converter and pipe outlet flanges and install retaining nuts. Do not tighten nuts. Remove jackstand. 5. Align exhaust system to specification, refer to appropriate illustration. 6. With exhaust system aligned: a. Tighten dual converter and pipe-to-exhaust manifold nuts to 34-46 Nm (25-34 lb-ft). b. Tighten muffler inlet flanges-to-dual converter and pipe outlet flanges retaining nuts to 29.7-40.3 Nm (22-30 lb-ft). 7. Attach air inlet tube to dual converter and pipe. Tighten clamp securely. 8. Check system for leaks and lower vehicle. 3.8L Engine Removal 1. Raise vehicle. Refer to Section 00-02. 2. Remove dual converter and pipe-to-exhaust manifold retaining nuts. 3. Remove dual converter and pipe outlet flange to muffler inlet flange retaining nuts. 4. Support dual converter and pipe with a suitable jackstand and remove exhaust converter frame bracket to dual converter Y pipe retaining nuts. 5. Remove dual converter and pipe from vehicle. 6. Replace any damaged parts. Installation 1. Loosely install dual converter and pipe and support with a suitable jackstand. 2. Install dual converter and pipe onto exhaust converter frame bracket and install retaining nuts. Tighten retaining nuts to 14.8-20.2 Nm (11-15 lb-ft). 3. Position dual converter and pipe to exhaust manifold studs and install retaining nuts. Do not tighten retaining nuts. 4. Position muffler inlet flange to dual converter and pipe outlet flange. Loosely install retaining nuts. 5. Align exhaust system to proper clearance specifications, as shown in the appropriate illustration. 6. With exhaust system aligned: a. Tighten dual converter and pipe to exhaust manifold nuts to 34-46 Nm (25-34 lb-ft). b. Tighten muffler inlet flange to dual converter and pipe flange retaining nuts to 29.7-40.3 Nm (22-30 lb-ft). 7. Check exhaust system for leaks.

Related entry:

(22666636) DRAIN TUBE - 2004 Saturn L300, cobalt flex pipe repair kit, 1988 L 9000 ford truck muffler, 2000 cavalier flex pipe 2 2, 2001 hyundai accent catalytic converter install, 2001 Mazda Dual Sport, how many catalytic converters on a 2010 buick lacrosse v6, how much to replace flex pipe in cars, mazda tribute exhaust manifold removal,

2008-2009 GMC Canyon, GMC Envoy 2008-2009 Saab 9-7X Engine Runs Rough (Inspect for Water Intrusion in Spark Plug Recess Area, Replace Spark Plug and Ignition Coil, Seal Ignition Coil Bolt Hole Vents and Seal Hood Air Grille)

0

Filed Under (GM) by admin on 04-06-2010

download
Models: 2008-2009 Chevrolet Colorado, TrailBlazer 2008-2009 GMC Canyon, Envoy 2008-2009 HUMMER H3, H3T 2008-2009 Saab 9-7X All Equipped With Engine RPOs LLR, LLV, LL8 Please Refer to GMVIS Condition Some customers may comment that the malfunction indicator lamp (MIL) is illuminated. Some customers may also comment that the engine runs rough. The technician may find DTCs P0300, P0301, P0302, P0303, P0304, P0305, or P0306 set as current or in history, depending on which engine the vehicle is equipped with. Upon further examination, the technician may observe evidence of water intrusion into the spark plug recess area. Cause This condition may be caused by an engine being exposed to a large quantity of water, which may result in some of the water seeping down past the vented threads of an ignition coil bolt, then flowing through the vent opening that is located in the bottom of the related ignition coil bolt hole, and collecting in the spark plug recess area. Correction Important: DO NOT reprogram or replace the engine control module (ECM) for this condition. If evidence of water intrusion in the spark plug recess area/s is not observed, then refer to the appropriate DTC procedures in SI.

Related entry:

2008 ford fusion ac drain, 2008 GMC acadia ac drain location, 2009 gmc acadia firing order diagram, 2004 envoy charging system, 2003 gmc envoy low side port, 04 gmc envoy hesitation during acceleration, 2008 envoy ac service port location, 2009 chevy traverse cilindros order checks, 2005 gmc envoy xl obd port, 2009 Acadia Firing Order,

2003–2004 Acura MDX Torque Converter Shudder or Vibration Between 35 and 40 MPH

0

Filed Under (Acura) by admin on 29-12-2010

download
PROBABLE CAUSE The torque converter is faulty. CORRECTIVE ACTION Replace the torque converter, or the torque converter and the transmission, and update the PCM with the HDS. NOTE: You must update the PCM to complete the repair.REPAIR PROCEDURE B Follow the IN-WARRANTY EXCHANGE steps in service bulletin 90-009, Automatic Transmission In- Warranty Exchange Program, to order a remanufactured A/T, replace the failed A/T, and return the failed A/T core. 1. Remove the transmission: • Refer to page 14-203 of the 2003–04 MDX Service Manual, or • Online, enter keyword A/T REM, and select A/T Removal from the list. 2. Clean the transmission cooler. Refer to service bulletin 89-015, ATF Cooler Cleaner. 3. Install a remanufactured transmission: • Refer to page 14-215 of the 2003–04 MDX Service Manual, or • Online, enter keyword A/T INSTALL, and select A/T Installation from the list. 4. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION). Refer to service bulletin 01-026, Updating the ECM/PCM. 5. Do the idle learn procedure: • Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off. • Start the engine and let it run until it reaches its normal operating temperature (cooling fan cycles twice). • Let the engine idle with the throttle fully closed for 10 minutes.

Related entry:

how much to torque acura legend headgasket, how to replace torque convertor 2004 acura mdx,

2003-2005 Chevrolet TrailBlazer Automatic Transmission/Torque Converter Clutch (TCC) Shudder

0

Filed Under (Chevrolet) by admin on 30-12-2010

download
Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. Correction First, repair the transmission and second, replace the transmission fill tube, seal and level indicator to prevent repeat water contamination of the ATF. Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: If water or coolant is found in the transmission, the following components MUST be replaced. • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow . Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube.

Related entry:

U241E Transmission Diagram, Toyota K 310 CVT transmission repair manual, pontiac torrent transmission fill plug socket, 1998 crv automatic transmission diagram, how to change automatic transmission oil on a 1999 mazda demio, 2005 mazda mpv transmission filter change instructions diagram, how change oricfice in 2004 chevy impala, 2002 saturn sl1 transmission diagram, exploded view of 2003 windstar transmission, buick rendezvous trans pan bolts torque,